Article
Free Journeyman Plumber Practice Test by State: 2026 Guide
Key Facts
- This directory contains 45 independent practice routes: 44 states and the District of Columbia. Route coverage is not a certification of every jurisdiction’s current licensing policy.
- The May 2025 BLS median for plumbers, pipefitters, and steamfitters is $63,800; the occupation’s projected employment growth is 7% from 2025 to 2035. These are combined occupational figures, not starting-pay promises.
- CSLB’s C-36 Plumbing study guide, publication 03-2026, describes a closed-book four-choice examination and lists the 2025 California Plumbing Code among its references.
- The C-36 approximate published domain weights are 22%, 22%, 20%, 19%, and 17%. These apply to that classification, not all journeyman plumbing examinations.
- Minnesota DLI’s linked plumbing examination guide describes the journeyworker examination as 240 points, 5½ hours, and a 70% passing score: 168 points. Points are not an official question count.
- Florida Statutes 489.1455 includes examination, apprenticeship-or-12,000-hour, and coursework conditions for its local journeyman licensing and recognition route. Confirm the exact local application and examination.
- The 2018 IPC distinguishes building drains and their branches in Table 710.1(1) from horizontal fixture branches and stacks in Table 710.1(2); a familiar pipe diameter does not identify the correct table.
- For 2018 IFGC study calculations, minimum test pressure is the greater of 1.5 times proposed maximum working pressure and 3 psig, subject to the section’s additional constraints.
- A personal 80% target on fresh, appropriately matched practice sets is an editorial study goal. It is not a universal official passing score or a guarantee of examination success.
Checking video availability…
A free journeyman plumber practice test is most useful when it matches the credential you will actually sit. Start with the 45 practice routes below: 44 states and the District of Columbia . Then confirm the licensing authority, examination name, approved references, and rules in your own candidate bulletin. A state name on a practice page does not establish a statewide journeyman licence or certify every question against your current examination.
This guide combines the directory with three official examples, a code-lookup method, ten worked practice questions, and a six-week study plan. The examples deliberately name their source and edition. Independent practice develops reasoning; it does not reproduce live examination questions or guarantee a passing score.
For career context, the U.S. Bureau of Labor Statistics reports a May 2025 median annual wage of $63,800 for plumbers, pipefitters, and steamfitters, with the highest tenth earning more than $108,420 . Its current projection is 7% employment growth from 2025 to 2035 . These figures describe the combined occupation, not a guaranteed journeyman starting salary.
Choose the credential before choosing the book
Write an “exam identity card” before paying an application fee or buying references:
- Confirm with the owner Record the exact answer
- Credential and authority Full licence/classification name; state board or local jurisdiction
- Eligibility Accepted experience, apprenticeship, education credits, and required documentation
- Examination Exam title/code, approved vendor, and the bulletin applicable to your appointment
- References Exact edition, state amendments, permitted tabs/annotations, and supplied materials
- Format and scoring Time, question or point count, sections, practical components, and passing rule
- Logistics Application and testing fees separately; ID, calculator, cancellation, and retake rules
Distinguish the code used on the examination from the code governing a new installation. A jurisdiction can adopt a newer construction code while its examination still specifies an older reference. Also distinguish a journeyworker credential from a contractor classification, a master licence, and a local registration. Passing one examination does not automatically confer another credential or authorize independent contracting.
If the authority and testing company appear to disagree, ask which bulletin applies to your examination date and save the written answer. Record the page, issue date, and date checked. An undated preparation website is not a substitute for that confirmation.
Free plumber practice directory: 44 states plus DC
These links are practice-resource navigation , not a verified catalogue of every jurisdiction’s licensing policy. The table preserves the available routes without assigning unverified code editions, fees, vendors, or experience requirements. Use the identity card above for the credential you need. A missing state is not evidence that no licence or examination exists there.
- Jurisdiction Practice route
- Alabama Free Alabama plumber practice
- Alaska Free Alaska plumber practice
- Arizona Free Arizona plumber practice
- Arkansas Free Arkansas plumber practice
- California Free California plumber practice
- Colorado Free Colorado plumber practice
- Connecticut Free Connecticut plumber practice
- Delaware Free Delaware plumber practice
- District of Columbia Free District of Columbia plumber practice
- Florida Free Florida plumber practice
- Georgia Free Georgia plumber practice
- Hawaii Free Hawaii plumber practice
- Idaho Free Idaho plumber practice
- Illinois Free Illinois plumber practice
- Indiana Free Indiana plumber practice
- Iowa Free Iowa plumber practice
- Kentucky Free Kentucky plumber practice
- Louisiana Free Louisiana plumber practice
- Maine Free Maine plumber practice
- Maryland Free Maryland plumber practice
- Massachusetts Free Massachusetts plumber practice
- Michigan Free Michigan plumber practice
- Minnesota Free Minnesota plumber practice
- Mississippi Free Mississippi plumber practice
- Montana Free Montana plumber practice
- Nevada Free Nevada plumber practice
- New Hampshire Free New Hampshire plumber practice
- New Jersey Free New Jersey plumber practice
- New Mexico Free New Mexico plumber practice
- North Carolina Free North Carolina plumber practice
- North Dakota Free North Dakota plumber practice
- Ohio Free Ohio plumber practice
- Oklahoma Free Oklahoma plumber practice
- Oregon Free Oregon plumber practice
- Rhode Island Free Rhode Island plumber practice
- South Carolina Free South Carolina plumber practice
- South Dakota Free South Dakota plumber practice
- Tennessee Free Tennessee plumber practice
- Texas Free Texas plumber practice
- Utah Free Utah plumber practice
- Vermont Free Vermont plumber practice
- Virginia Free Virginia plumber practice
- Washington Free Washington plumber practice
- West Virginia Free West Virginia plumber practice
- Wisconsin Free Wisconsin plumber practice
For broader exercises, use national IPC-focused plumber practice , UPC-focused practice , or master-plumber practice . Choose by the named reference and your learning objective. A larger collection is not automatically a closer match to your examination. Do not add counts from overlapping collections to estimate unique questions.
- Three official examples that change how you prepare
- California: study the C-36 contractor classification
The CSLB C-36 study guide , publication 03-2026 , identifies a closed-book Plumbing examination with four-choice, one-best-answer questions and a supplied calculator. Its reference list includes the 2025 California Plumbing Code . An older copy of the guide can list different editions; check the publication footer as well as the title.
The approximate C-36 outline is Planning and Estimating 22% , Underground and Rough Systems 22% , Finish Plumbing Installations 20% , Service/Repair/Remodel 19% , and Safety 17% . Those five values total 100%; they are C-36 weights , not a national journeyman blueprint. Planning includes estimating and drawings, while rough systems include fuel gas and testing. A preparation plan that consists only of drainage-table memorization misses substantial published content. Use the CSLB examination FAQ for appointment-specific procedures and timing.
Minnesota: distinguish points from questions
Minnesota DLI’s plumbing examination guide , labelled April 2022 in the supplied guide, states 240 points , 5½ hours , and a 70% passing score for the journeyworker examination. Therefore 168 points reaches 70%. Do not turn “240 points” into “240 questions,” or replace the owner’s scoring description with an assumed all-MCQ format. Its preparation material includes drawing interpretation; practise tracing an entire drainage or vent path rather than isolated numbers alone. Check DLI’s current instructions and the references supplied for your appointment.
Florida: identify the local credential and statutory route
Florida Statutes 489.1455 addresses local journeyman licensing and recognition. Its conditions include an approved proctored examination, at least 75% for an examination taken after October 1, 1997 , a registered state-approved apprenticeship or at least 12,000 hours of trade training, and the specified coursework condition. The authorized six-month proof option belongs to that coursework provision; it is not a general waiver of experience.
The statute also requires recognition of a qualifying local journeyman licence by other Florida counties and municipalities. It does not establish one universal Florida journeyman test length, vendor, fee, or reference list. Obtain the exact local application and examination bulletin. Do not confuse this route with a statewide plumbing-contractor licence.
Learn the lookup method, not an unlabelled number
The following are 2018 IPC model-code study examples , not statements that every directory jurisdiction currently tests that edition. Start a lookup by naming the system component: a horizontal fixture branch, building drain, stack, fixture supply, and vent can require different tables.
Slope: IPC Table 704.1 groups drainage piping by size. For ordinary 3–6-inch drainage piping its listed minimum is 1/8 inch per foot; piping upstream of a grease interceptor instead needs at least 1/4 inch per foot under Section 704.1. Identify that condition before using the general table.
Drainage capacity: Table 710.1(1) covers building drains and sewers, including branches of the building drain, and uses slope columns. Table 710.1(2) covers horizontal fixture branches and stacks; its footnote excludes branches of the building drain. Its 3-inch horizontal-branch limit is 20 drainage fixture units (dfu). The building-drain table’s water-closet footnote requires a minimum 3-inch drain; it does not impose a blanket two-water-closet maximum. Total load, slope, layout, and other applicable rules still matter.
Water supply: Table 604.3 specifies flow pressure at fixture supply outlets under peak demand. It lists 8 psi for a residential sink but 20 psi for a close-coupled tank water closet. A single “all fixtures need 8 psi” memory rule gives the wrong answer. Static service pressure is a different measurement.
Venting: Table 909.1 lists a 6-foot maximum trap-to-vent distance for a 1½-inch trap at 1/4 inch per foot. Read Sections 909.1–909.3 too: table distances do not waive limits on fall, the vent connection, or crown venting. The self-siphoning-fixture exception must not be applied to every sink.
Water heating and traps: IPC 607.3 locates thermal-expansion control on the heater’s cold supply downstream of the listed check/reducing/backflow devices. IPC 1002.4 gives the ordinary trap liquid-seal range as 2–4 inches, with a special accessible-fixture design exception. Distinguish a trap’s seal depth from its pipe diameter.
Read the actual IPC drainage chapter , water-supply chapter , vent chapter , and trap chapter . A table heading, footnote, exception, and adjacent section form one lookup. Record all four in your error log. Do not transfer an IPC result into a UPC or state-amended question without checking that reference.
Fuel-gas questions need their own conditions
Study gas only where it belongs in your specified outline. For a 2018 IFGC calculation, Sections 406.4.1–406.4.2 require a test pressure of at least 1.5 times the proposed maximum working pressure and at least 3 psig . Select the larger value, rather than treating these as interchangeable choices. A 4-psig proposed working pressure therefore requires at least 6 psig under this rule. Above a 125-psig test pressure, the additional hoop-stress restriction also matters.
The general duration is at least half an hour for each 500 cubic feet of pipe volume or fraction thereof . The shorter provision applies to a system with volume less than 10 cubic feet OR a system in a single-family dwelling : at least ten minutes. It does not require both conditions. A non-single-family system of exactly 10 cubic feet does not meet the “less than 10” condition. The section does not require a duration exceeding 24 hours. These are examination lookups, not a complete field testing procedure; isolation, equipment, test medium, approvals, and local amendments remain separate requirements.
Trade math: show units before using a shortcut
Write the units beside each input. Fall in inches = run in feet × slope in inches per foot. Thus a 24-foot run at 1/8 inch per foot falls 3 inches. This is a calculation using a stated slope, not proof that the slope is permitted for every material or application.
For an ideal 45-degree offset, the centreline travel is offset × √2. An 18-inch offset gives about 25.46 inches of travel before fitting takeoffs. Do not subtract an assumed takeoff: use the actual fitting dimensions supplied in the problem.
Using the NIST US-gallon conversion , 1 US gallon equals exactly 231 cubic inches. For a full cylindrical pipe, volume is π × inside diameter² × length ÷ 4. With diameter and length both in feet , multiply cubic feet by approximately 7.48052 to obtain US gallons, giving approximately 5.87519 × diameter² × length . With diameter in inches and length in feet , the coefficient becomes approximately 0.04080 . Nominal pipe size is not necessarily inside diameter. For pressure-test duration, keep the final volume in cubic feet rather than silently substituting gallons.
Ten worked plumber practice questions
These original exercises use the stated reference or assumptions. Cover the answer before solving. A correct calculation alone does not establish that an entire installation complies.
1. Under 2018 IPC 704.1, what minimum slope applies to a 3-inch drain upstream of a grease interceptor?
- A) 1/16 inch per foot
- B) 1/8 inch per foot
- C) 1/4 inch per foot
- D) 1/2 inch per foot
Answer: C. The grease-interceptor condition requires at least 1/4 inch per foot. B is the ordinary 3–6-inch table value without this condition. A is another size band; D exceeds the specified minimum.
2. Which 2018 IPC table sizes a branch of the building drain?
- A) Table 710.1(1), using its applicable slope column
- B) Table 710.1(2), using the horizontal-fixture-branch column
- C) Table 909.1, using the trap-size row
- D) Table 604.3, using the fixture-supply row
Answer: A. The building-drain table expressly includes its branches. Table 710.1(2) excludes those branches; the other tables address vent distance and water supply. Identify the component before choosing a familiar diameter.
3. An ordinary fixture trap has no special accessible-fixture design. What liquid seal range does 2018 IPC 1002.4 specify?
- A) 1–2 inches
- B) 2–4 inches
- C) 3–6 inches
- D) 4–8 inches
Answer: B. The ordinary limits are 2 and 4 inches. The other ranges admit seal depths outside those limits. The stem excludes the section’s special-design exception.
4. Under 2018 IPC Table 604.3, which minimum flow pressure applies to a close-coupled tank water closet?
- A) 8 psi
- B) 15 psi
- C) 20 psi
- D) 35 psi
Answer: C. Read the exact fixture row: 20 psi. The 8-psi sink/lavatory value does not cover this closet. The 35-psi value belongs to the siphonic flushometer-valve row; 15 psi is not this row’s requirement.
5. A 1½-inch trap is being checked at the 1/4-inch-per-foot slope in 2018 IPC Table 909.1. What maximum trap-to-vent distance does that row give?
- A) 4 feet
- B) 5 feet
- C) 6 feet
- D) 8 feet
Answer: C. The row gives 6 feet. Five feet corresponds to the smaller 1¼-inch row; eight feet to the 2-inch row. Four feet is not the requested table value. Adjacent venting conditions must still be checked.
6. What is the calculated fall over a 24-foot run at a stated slope of 1/8 inch per foot?
- A) 1½ inches
- B) 3 inches
- C) 6 inches
- D) 12 inches
Answer: B. 24 × 1/8 = 3 inches. Six inches would use 1/4 inch per foot, and twelve would use 1/2. The problem asks for fall, not pipe diameter or a determination of permitted slope.
7. A 2018 IFGC study problem specifies a proposed maximum working pressure of 4 psig. Under 406.4.1, what minimum test pressure follows before considering any separate constraints?
- A) 3 psig
- B) 4 psig
- C) 6 psig
- D) 8 psig
Answer: C. 1.5 × 4 = 6 psig, which exceeds the 3-psig floor. Three fails the multiplier; four repeats working pressure; eight doubles it unnecessarily. This answer is not a complete testing procedure.
8. A non-single-family 2018 IFGC practice system has a pipe volume of 501 cubic feet. What minimum duration follows from 406.4.2’s general volume rule?
- A) 10 minutes
- B) 30 minutes
- C) 60 minutes
- D) 90 minutes
Answer: C. The fraction of the second 500-cubic-foot increment counts: two half-hours total 60 minutes. Thirty minutes covers only the first increment; ten minutes does not apply to these facts; ninety counts an extra increment.
9. For an ideal 45-degree offset of 18 inches, what is centreline travel to the nearest hundredth, before takeoffs?
- A) 12.73 inches
- B) 18.00 inches
- C) 25.46 inches
- D) 36.00 inches
Answer: C. 18 × √2 ≈ 25.46 inches. Dividing by √2 reverses the relationship; using 18 ignores travel; doubling is not the 45-degree relationship. Actual fitting dimensions determine any takeoff adjustment.
10. Under 2018 IPC 607.3, a storage heater’s cold supply passes through a check valve. Where does the required expansion-control connection belong?
- A) On the cold supply upstream of that check valve
- B) On the cold supply downstream of that check valve
- C) On the relief-valve discharge instead of the cold supply
- D) On an isolated branch beyond a closed shutoff valve
Answer: B. The control connection must be downstream of all the listed restricting devices on the heater’s cold supply. An upstream or isolated connection cannot serve the trapped supply as required. The relief discharge is a different safety component, not the location specified by 607.3.
A six-week study plan you can adapt
This is an editorial sequence, not an authority-mandated course or a promise of readiness in six weeks. Use your actual outline to allocate time and extend the schedule when a diagnostic reveals gaps.
Weeks 1–2: identify, organize, and diagnose. Complete the exam identity card. Obtain the exact references and amendment documents. For an open-book examination, practise with only permitted tabs and annotations; confirm the rules before marking books. For a closed-book examination, pair recall drills with explanations of why each rule applies. Complete a diagnostic, then classify each miss as wrong edition, wrong component/table, missed condition, arithmetic, or unfamiliar subject.
Weeks 3–4: solve systems, not isolated facts. Trace flow through drawings and mark the load added at each connection. Keep drainage fixture units separate from water-supply fixture units and actual flow rates. Work both a successful lookup and a near-miss version: a fixture branch versus a building-drain branch, ordinary drainage versus grease-interceptor drainage, or a sink versus a tank closet. Add fixture, water-heater, backflow, safety, estimating, and repair topics wherever your official outline requires them. There is no single nationwide percentage allocation for these subjects.
Weeks 5–6: apply the actual test constraints. Add gas, law, or drawing tasks when your named examination includes them. Use the official time and section rules for simulations; a short practice quiz is not automatically a full-length exam. Check every wrong answer against the named source and explain why the closest distractor fails. An 80% practice target can be a personal buffer for fresh sets, but it is neither a published universal passing score nor a guarantee. Repeating memorized questions until the percentage rises gives less evidence than solving unfamiliar, appropriately matched problems.
Before exam day, recheck the appointment notice, identification, permitted materials, calculator rules, and reporting time. Use the practice directory above to begin, the owner’s current instructions to define your target, and an error log to decide what to study next.
Frequently asked questions
Does a state practice page prove that I need a statewide journeyman licence?
No. The directory identifies practice routes, not a uniform licensing system. Confirm your full credential name and state or local authority. Contractor, journeyworker, master, and local registration pathways are different; a practice-page label does not decide which one applies to you.
Which code book should I use for my plumber examination?
Use the edition, amendments, and permitted-reference list in the bulletin that applies to your exact examination and appointment. The examination reference can differ from the construction code currently adopted for new work. The technical exercises here expressly identify the 2018 IPC or IFGC where used; they do not establish your local adoption.
What does the current California C-36 guide say?
The CSLB Plumbing study guide, publication 03-2026, describes a closed-book, four-choice, one-best-answer examination with a supplied calculator and lists the 2025 California Plumbing Code among its references. Its approximate weights are 22% planning/estimating, 22% underground/rough systems, 20% finish installations, 19% service/repair/remodel, and 17% safety. C-36 is a contractor classification, not a generic nationwide journeyman credential.
Does Minnesota’s 240-point journeyworker exam mean 240 questions?
No. The linked DLI plumbing examination guide describes 240 points, a 70% passing score, and 5½ hours for the journeyworker exam. Seventy percent of 240 is 168 points. Do not infer a question count or an all-multiple-choice format from the total points; check DLI’s current candidate instructions.
Is there one Florida journeyman plumber test format?
Do not assume one statewide format. Identify the local licensing authority and accepted examination. Florida Statutes 489.1455 addresses local journeyman licensing and recognition, including its examination-score, training, and coursework conditions. It does not provide one universal question count, duration, vendor, or fee for every local examination.
Are plumber exams all open book and passed at 70%?
No universal rule should be inferred. For example, CSLB’s C-36 guide expressly says closed book; Minnesota’s guide specifies 70% for its examination. Florida’s cited statutory route requires at least 75% on the specified approved proctored examination taken after October 1, 1997. Read the rule for your own credential rather than generalizing from these examples.
How should I choose practice questions?
Match the named credential, reference edition, subjects, and task types before looking at collection size. Read the full explanation, verify the cited condition, and log why each distractor fails. Use fresh questions to assess reasoning; overlapping state and national collections should not be summed as if every item were unique.
Will an 80% practice score guarantee that I pass?
No. Eighty percent can be a personal preparation target on fresh, relevant questions. It is not an official nationwide cut score, a conversion to a particular exam’s score, or proof that the practice set covers every tested subject. Use the owner’s published scoring rule and investigate remaining weaknesses.