Cheat sheet

Red Seal Millwright Cheat Sheet

Practice this exam

Common Occupational Skills

  • 19% of exam
  • Exam Breakdown Question Types Formulas Provided Exam Acronyms Safety and Tools

Rigging, Hoisting, Moving

  • 13% of exam
  • Rigging Numbers Rigging Hardware Rigging Decision Picker Plan Every Lift

Mechanical Power Transmission

  • 23% of exam
  • Bearings and Seals Shaft Alignment Drives, Gears, Couplings Alignment Method Picker

Material Handling, Process Systems

  • 18% of exam
  • Pumps and Compressors Conveying and Process Pump and Compressor Picker Centrifugal vs Positive

Fluid Power Systems

  • 15% of exam
  • Fluid Power Basics Pressure and Flow Units Hydraulic vs Pneumatic Fluid Power Three

Maintenance and Commissioning

  • 12% of exam
  • Maintenance Methods NDT and Vibration Monitoring Method Picker Preventive vs Predictive

Quick Facts

  • Exam Industrial Mechanic (Millwright)
  • Questions 135 multiple-choice
  • Time 4 hours
  • Pass 70%
  • Options Four, one correct
  • Sections Six major work activities
  • Blueprint 2017 standard, current exams
  • Fee Set by province
  • Delivered by Provincial apprenticeship authority
  • Provided Formulas and acronyms

Six Exam Sections CO

  • Common, Rigging, Power, Material, Fluid, Maintenance
  • A: 25 questions B: 17 questions C: 32 questions D: 24 questions E: 21 questions F: 16 questions

Common Core vs Not CO

Common core

  • 70% of jurisdictions perform
  • Testable on exam
  • Study every sub-task

Not common core

  • Under 70% of jurisdictions
  • Never tested
  • GTAW welding here
  • Tested vs not tested

Exam Breakdown CO

  • A Common occupational skills 25 questions, 19% MWA A
  • B Rigging and hoisting 17 questions, 13% MWA B
  • C Power transmission 32 questions, 23% MWA C
  • D Material handling, process 24 questions, 18% MWA D
  • E Fluid power 21 questions, 15% MWA E
  • F Maintenance, commissioning 16 questions, 12% MWA F

Question Types CO

  • Knowledge and recall 30-40% of questions
  • Procedural and application 40-50% of questions
  • Critical thinking 20-30% of questions
  • Answer options Four, one correct
  • Trick questions None on Red Seal
  • Question value One mark each
  • Guessing Answer every question

Formulas Provided CO

  • Force Pressure x area
  • Area of circle pi x radius squared
  • Volume of cylinder height x pi x radius squared
  • Surface speed rpm x pi x diameter
  • Gear pass frequency rpm x number of teeth
  • Thermal expansion temp change x length x coefficient
  • Shim at point X G x A/B
  • Steel weight 490 lb per cubic foot
  • Steel weight, metric 7 849 kg per cubic metre
  • Pythagorean theorem Right triangle side lengths

Exam Acronyms CO

  • CMMS Computerized maintenance management system
  • FLRA Field level risk assessment
  • FMEA Failure modes and effects analysis
  • NLGI National Lubricating Grease Institute
  • NDT Non-destructive testing
  • SCBA Self-contained breathing apparatus
  • SDS Safety data sheet
  • WHMIS Workplace hazardous materials information system
  • SWP Safe work procedure
  • SMAW Shielded metal arc welding
  • sfpm Surface feet per minute
  • tpi Teeth per inch
  • TDC, BDC Top, bottom dead centre
  • OEM Original equipment manufacturer

Safety and Tools CO

  • PPE Personal protective equipment
  • LOTO Lock-out/tag-out, zero energy
  • Stored energy Accumulators, springs, suspended loads
  • Hand tools Wrenches, hammers, pry bars
  • Portable power tools Grinders, saws, drills
  • Precision measuring tools Micrometers, calipers, dial indicators
  • Lubricant types Oil, grease, dry solid
  • Lubricant properties Viscosity, flash point, additives
  • Cutting and welding Oxy-fuel, plasma arc, SMAW
  • Safety devices Light curtains, e-stops, guards

Plan Every Lift RI

  • Weight, gear, area, signals
  • Weight: include hardware Gear: inspect and certify Area: secure it Signals: agree first

Working Load vs Breaking RI

Working load limit

  • Rated safe capacity
  • Design factor applied
  • Shown on sling tag

Breaking strength

  • Load at failure
  • Never a work rating
  • Testing value only
  • Rated vs failure

Rigging Decision Picker RI

  • Load weight unknown → Calculate before lifting ( Add hardware weight )
  • Long or flexible load → Spreader beam
  • Rope must change direction → Snatch block
  • Load may swing → Tag line
  • Crane out of sight → Radio or hand signals
  • Sling damaged or untagged → Remove from service ( Tag and report )
  • Unusual lift beyond practice → Engineered lift ( Engineer-approved design )
  • Wire rope clips needed → 3 x diameter + 1 ( Rope to 7/8 in. )

Rigging Numbers RI

  • Sling stress Length/height x weight per leg
  • Sling legs counted Maximum three legs
  • Clips, rope to 7/8 in. 3 x diameter + 1
  • Clips, rope 1 in. larger 3 x diameter + 2
  • Clip spacing 6 x rope diameter
  • 6x19 rope WLL diameter squared x 8

Rigging Hardware RI

  • Shackle Connects sling to load
  • Spreader beam Separates lift points
  • Snatch block Redirects wire rope
  • Tag line Controls load swing
  • Eye bolt Threaded lifting point
  • Safety latch Keeps sling in hook
  • Grip hoist, tirfor Manual wire rope puller
  • Lever chain hoist Manual lift and pull
  • IWRC Independent wire rope core

Alignment Order PO

  • Rough first, then dial or laser
  • Rough: straight edge Dial: rim-and-face Reverse: long spans Laser: fastest precise

Plain vs Rolling Bearings PO

Plain (friction)

  • Sliding surfaces
  • Babbitt lining common
  • Plasti-gauge checks clearance

Anti-friction

  • Rolling elements
  • Heat or press fit
  • Induction heater, oil bath
  • Slides vs rolls

Alignment Method Picker PO

  • Rough positioning only → Straight edge, feeler gauge ( Rough alignment )
  • Machine rocks on base → Correct soft foot first ( Before dialing )
  • Piping distorts the casing → Relieve pipe strain
  • Precision, short coupling → Rim-and-face dial ( One indicator set )
  • Long span or sag → Reverse dial method ( Two indicators )
  • Fast precise alignment → Laser alignment
  • Machine runs hot → Set cold offsets ( Thermal growth )
  • Shims must be calculated → G x A/B ( Provided formula )

Bearings and Seals PO

  • Bearing Lets parts rotate together
  • Bearing types Plain friction, anti-friction rolling
  • Babbitt Plain bearing lining material
  • Seal types Static, dynamic, mechanical, non-contacting
  • Non-contacting seal Labyrinth or annulus
  • Shaft types Drive, counter, jack, hollow
  • Shaft accessories Keys, pins, taper bushings
  • Plain bearing fit tools Plasti-gauge, lead wire, bluing
  • Rolling bearing mounting Induction heater, oil bath
  • Fit specifications Loads, temperature, pressure, rpm

Pre-Alignment Checks PO

  • Soft foot, pipe strain, run-out, float
  • Soft foot: rocking base Pipe strain: piping pulls Run-out: bent shaft End float: axial play

Rim-and-Face vs Reverse Dial PO

Rim-and-face

  • One indicator setup
  • Face reads angular
  • Short coupling spans

Reverse dial

  • Two indicators, both rims
  • Sag compensated
  • Long coupling spans
  • Face reading vs rims

Shaft Alignment PO

  • Alignment methods Rough, dial, laser, optical
  • Dial methods Rim-and-face, reverse, cross
  • Rough alignment tools Straight edge, feeler gauge
  • Pre-alignment defects Soft foot, pipe strain
  • Soft foot Machine foot not seated
  • Pipe strain Piping pulls machine casing
  • Shaft run-out Bent or eccentric shaft
  • End float Axial shaft movement
  • Bar sag Bracket droop skews readings
  • Thermal growth Cold offset for heat
  • Shim formula G x A/B

Drives, Gears, Couplings PO

  • Chain drives Roller, silent, composite, lube-free
  • Belt drives V-belt, cog, timing, flat
  • Gear types Spur, bevel, spiral, herringbone, helical
  • Worm gear Right-angle, high reduction
  • Hypoid gear Shafts intersect different plane
  • Backlash Clearance between mating teeth
  • Tooth contact Engagement pattern of teeth
  • Couplings Rigid, elastomeric, grid, fluid
  • Clutches Overrunning, friction, positive, electromagnetic
  • Brakes Friction, wet disc, electromagnetic
  • Arc of contact Belt wrap on sheave
  • Lubricant systems Oil bath, drip, pressurized

Centrifugal vs Positive MA

Centrifugal

  • Non-positive displacement
  • Flow varies with head
  • Impeller adds velocity

Positive displacement

  • Fixed volume per cycle
  • Needs relief valve
  • Handles viscous fluid
  • Varying vs fixed flow

Pump and Compressor Picker MA

  • High flow, low head → Centrifugal pump ( Non-positive )
  • Constant volume required → Positive displacement pump
  • Viscous fluid to move → Positive displacement pump
  • Move air, low pressure → Fan or blower
  • High pressure compressed air → Reciprocating compressor ( Positive displacement )
  • Continuous large airflow → Centrifugal compressor ( Dynamic type )
  • Bulk solids to move → Belt or screw conveyor

Pumps and Compressors MA

  • Pump families Non-positive centrifugal, positive displacement
  • Positive displacement Fixed volume, no slip
  • Axial flow Flow along the axis
  • Centrifugal flow Flow 90 degrees outward
  • Compressor families Dynamic centrifugal, positive displacement
  • Displacement compressors Reciprocating, radial, screw, vane
  • Pump seals Packing, O-ring, mechanical, V-ring
  • Fan Creates air movement
  • Blower Moves air, higher pressure
  • Agitator Keeps tank material moving

Conveying and Process MA

  • Conveying system Moves solid material along
  • Conveyor types Belt, roller, chain, screw
  • More conveyor types Bucket, pneumatic, flume water
  • Dust filters Cyclones, bag shakers, screens
  • Process piping scope Piping, tanks, containers
  • Conditions monitored Temperature, vibration, pressure, flow
  • Robotics questions One of 135

Fluid Power Three FL

  • Hydraulic, pneumatic, vacuum
  • Hydraulic: 12 questions Pneumatic/vacuum: 9 questions Section total: 21 questions

Hydraulic vs Pneumatic FL

Hydraulic

  • Liquid, nearly incompressible
  • High force, precise control
  • 12 of 135 questions

Pneumatic and vacuum

  • Compressed air, compressible
  • Faster and cleaner
  • 9 of 135 questions
  • Force vs speed

Fluid Power Basics FL

  • Fluid power Hydraulic, pneumatic, vacuum
  • Fluid Liquid or gas that flows
  • Core components Pumps, motors, actuators, valves
  • More components Accumulators, filters, strainers, conductors
  • DCV Directional control valve
  • FRL Filter regulator lubricator
  • Cylinder force Pressure x area
  • Hydraulic questions 12 of 135
  • Pneumatic, vacuum questions 9 of 135

Pressure and Flow Units FL

  • psi Pounds per square inch
  • psig Pounds per square inch gauge
  • psia Pounds per square inch absolute
  • kPa Kilopascal, metric pressure
  • Hg Mercury, vacuum measurement
  • gpm Gallons per minute
  • N Newton, force unit
  • hp Horsepower
  • rpm Revolutions per minute

Sensory Inspection MA

  • Look, listen, feel, smell
  • Look: leaks, wear Listen: noise Feel: heat, vibration Smell: burning

Preventive vs Predictive MA

Preventive

  • Scheduled, periodic
  • Based on past experience
  • Time or run hours

Predictive

  • Condition data driven
  • Proactive monitoring
  • Vibration, oil, thermography
  • Calendar vs condition

Monitoring Method Picker MA

  • Bearing wear suspected → Vibration analysis
  • Hot spots suspected → Thermography
  • Oil condition unknown → Fluid analysis ( Ferrography for wear )
  • Surface cracks suspected → Dye penetrant
  • Cracks in ferrous steel → Magnetic particle ( Ferrous only )
  • Internal weld flaws → Radiography or ultrasonic
  • Leak check needed → Air or water pressure
  • Nothing visible or audible → Condition-based monitoring

Maintenance Methods MA

  • Preventive maintenance Scheduled, periodic inspections
  • Predictive maintenance Uses performance data proactively
  • Condition-based monitoring Finds faults beyond senses
  • Monitoring methods Vibration, fluid analysis, thermography
  • More monitoring methods Ultrasonic, tribology, speed monitoring
  • Tribology Friction, wear, lubrication study
  • Ferrography Wear particles in oil
  • Sensory inspection Sight, sound, smell, touch
  • Baseline readings Vibration, temperature, fluid, ultrasound
  • Commissioning scope Bring equipment into service
  • Decommissioning scope Disassembly, removal of machines

Commission vs Decommission MA

Commissioning

  • Bring system into service
  • Verify against specification
  • Record baseline readings

Decommissioning

  • Take system out
  • Disassembly and removal
  • Decontamination and records
  • Start up vs remove

NDT and Vibration MA

  • NDT methods Dye penetrant, magnetic particle
  • More NDT methods Radiography, ultrasonic, visual, thermography
  • Pressure testing Air or water pressure
  • Eddy current Electromagnetic surface flaw check
  • Vibration analysis Monitors condition, diagnoses faults
  • Vibration causes Imbalance, misalignment, looseness, eccentricity
  • More vibration causes Shaft faults, natural frequencies
  • Vibration tools Data collector, probes, strobe
  • Multi-plane balancing Balancing over two planes
  • Thermographic equipment Shows temperature via infrared

Common Traps

Preventive vs predictive

  • Preventive follows schedule ≠ Predictive follows condition

Bearing families

  • Plain bearings slide ≠ Rolling bearings roll

Pump families

  • Centrifugal is non-positive ≠ Displacement pumps are fixed

Alignment sequence

  • Soft foot corrected first ≠ Dial readings come after

Section size

  • Power transmission is 32 ≠ Maintenance is only 16

Common core rule

  • Common core is tested ≠ Non-core is never tested

Standard versions

  • Current exams use 2017 ≠ New 2026 exams pending

Who sets what

  • Red Seal sets exam ≠ Provinces set fees

Sling angle

  • Flatter slings raise tension ≠ Vertical legs carry least

Last Minute

  • 1. 135 questions, 70% to pass
  • 2. Four hours, four options each
  • 3. Power transmission largest: 32 questions
  • 4. Common skills next: 25 questions
  • 5. Material handling: 24 questions
  • 6. Fluid power: hydraulic 12, pneumatic 9
  • 7. Rigging and hoisting: 17 questions
  • 8. Maintenance smallest: 16 questions
  • 9. Alignment order: rough, dial, laser
  • 10. Plain bearings slide, rolling roll
  • 11. Preventive scheduled, predictive condition-based
  • 12. Wire rope clip spacing: 6 diameters
  • 13. Add rigging hardware to load
  • 14. Calculator and formulas are provided
  • 15. Current exams follow 2017 standard

Red Seal Industrial Mechanic (Millwright) (Interprovincial Exam)

  • Practice Questions 126 questions Study Guide 65 topics Cheat Sheet 151 facts Flashcards 50 cards Shorts 1 short Podcast