Cheat sheet

Red Seal Truck and Transport Mechanic Cheat Sheet

Practice this exam

A: Common Occupational Skills

  • 6% of exam
  • Safe Work Service identity Hoisting Fasteners

B: Engines and Supporting Systems

  • 16% of exam
  • Engine Tests Aftertreatment Compression Rail service

C: Air Systems and Brake Systems

  • 13% of exam
  • Air and Brake Checks Governor Brake stroke Spring chamber

D: Electrical and Electronic Systems

  • 16% of exam
  • Electrical Relationships Electrical Diagnosis Loaded voltage drop No communication

E: Drive Trains

  • 12% of exam
  • Drivetrain Checks Clutch release AMT calibration Axle ratio

F: Steering, Chassis/Frames, Suspensions, Tires, Wheels, Hubs

  • 13% of exam
  • Chassis and Wheel Checks Kingpin play Multi-piece rim Wheel bearing

G: Cabs

  • 4% of exam
  • Cab Checks Seat drops Wiper stalls SRS service

H: Trailers

  • 6% of exam
  • Trailer Checks Landing gear Reefer service Defrost

I: Climate Control Systems

  • 5% of exam
  • Climate Checks Evaporator Condenser Heater airflow

J: Hydraulic Systems

  • 6% of exam
  • Hydraulic Checks Hydraulic force Slow actuator Injection injury

K: Hybrid and Electric Vehicles

  • 3% of exam
  • High-Voltage Safety Qualified HV technician Isolation Verification

Quick Facts

  • Official questions 135 multiple-choice questions
  • Writing time 4 hours
  • Passing mark 70%
  • Answer format Four options; one correct answer
  • Blueprint 11 blocks; A–K
  • Largest block Electrical/electronic systems; 22 questions
  • Weights Published percentages; counts shown below
  • Supplied references Trade formulas and acronyms
  • Ontario identity Truck and Coach Technician; 310T
  • Fees and rewrites Confirm provincial/territorial authority rules

Diagnostic Sequence CO

  • Confirm → Measure → Compare → Repair → Verify
  • Confirm: concern and conditions Measure: prescribed tests Compare: OEM expected values Verify: retest and document

Safe Test Picker CO

  • Before work beneath raised truck → Rated support; secure against movement ( OEM lift points and locks )
  • Before high-voltage component work → Qualified technician; OEM isolation procedure ( Discharge; verify with rated equipment )
  • Before pressurized fuel line service → OEM shutdown, isolation, depressurization ( Verify pressure safe before opening )
  • Before cooling pressure test → Safe temperature; OEM test pressure ( Correct tester and adapters )
  • Excess automatic-adjuster stroke → Adjuster and foundation-brake cause diagnosis ( Chamber-specific pressure and stroke limits )
  • Before reefer inspection/service → Qualified service; disable automatic start ( Isolate unit-specific energy sources )
  • Slow hydraulic actuator → Flow, restriction, leakage tests ( Specified load and operating conditions )
  • Hydraulic injection puncture → Seek immediate emergency medical treatment ( Identify injected fluid )
  • Before multi-piece rim inflation → Trained personnel; prescribed restraining device ( Stay outside possible component trajectory )

Safe Work CO

  • Lockout Isolate, restrain, dissipate, verify energy Block A: 8 questions
  • Raised truck Rated supports; lock lift; restrain vehicle
  • Hoisting Load, sling angle, anchor ratings
  • Service identity VIN, component ID, current bulletins
  • Fasteners OEM torque, sequence, replacement rules
  • Fluid selection Application, climate, OEM grade
  • Mentoring Demonstrate; learner practices; give feedback

Compression vs Leakage EN

Compression

  • Measures developed cylinder pressure
  • Specified cranking/test conditions

Leakage

  • Introduces regulated test air
  • Escape path helps locate leak
  • Measure sealing; then localize leakage

Engine Tests EN

  • Compression Measures cylinder sealing performance Block B: 21 questions
  • Leakage test Locates escaping test air
  • Low oil-pressure warning Stop safely; verify specified gauge pressure
  • CAC leaks OEM pressure-limited leak test
  • Rail service OEM shutdown; isolate; verify depressurization
  • Cooling test Safe temperature; OEM test pressure
  • Engine retarder Supplements service-brake deceleration

Soot vs Ash EN

Soot

  • Combustible trapped particulate
  • Regeneration oxidizes it

Ash

  • Noncombustible residue
  • Specified cleaning/removal
  • Regeneration does not remove ash

Aftertreatment EN

  • DPF Traps soot in porous filter
  • Regeneration Oxidizes soot; leaves ash
  • Ash Specified cleaning or filter replacement
  • SCR DEF-supported catalytic NOx reduction
  • Exhaust diagnosis Pressure, temperature, dosing; OEM tests

Relay Memory AI

  • Relay receives control; reservoir supplies chambers
  • Control line: foot-valve signal Supply line: local reservoir air

Service vs Spring Brake AI

Service chamber

  • Air pressure applies braking
  • Pedal-commanded brake demand

Spring chamber

  • Spring applies parking brake
  • Air releases powerful spring
  • No air still leaves spring energy

Air and Brake Checks AI

  • Governor cut-in Compressor resumes charging Block C: 17 questions
  • Governor cut-out Compressor unloads
  • Air dryer Removes moisture; reservoirs still checked
  • Relay valve Local reservoir supplies brake chambers
  • Spring chamber Stored spring energy; never disassemble
  • Brake stroke Chamber-specific limits and test pressure
  • Automatic slack adjuster Excess stroke requires cause diagnosis
  • ABS warning Codes and system tests required

Electrical Relationships EL

  • Voltage = current × resistance; DC power = voltage × current
  • V: volts I: amperes R: ohms P: DC power in watts

Series vs Parallel Batteries EL

Series

  • Compatible voltages add
  • Two 12 V → 24 V

Parallel

  • Voltage remains nominally equal
  • Compatible capacity increases
  • Follow OEM battery compatibility requirements

Electrical Test Picker EL

  • No crank → Battery, loaded cables, start command ( Retain safety interlocks; OEM tests )
  • Normal battery; slow crank → Loaded power and ground drops ( Compare OEM limits )
  • Missing spark → Approved spark tester; supply/control checks ( OEM spark-ignition procedure )
  • Module will not communicate → Power, grounds, data-link tests ( Vehicle wiring diagram )
  • Resistance measurement needed → De-energize; discharge; isolate parallel paths ( Follow applicable OEM procedure )
  • Alternator output seems low → Specified speed/load; cable-drop tests ( Check belt and regulator control )
  • Code points to sensor → Test supply, ground, signal ( Code alone does not prove failure )
  • Intermittent electrical concern → Connections, wiring; logged data ( Preserve codes before clearing )
  • Electrical repair completed → Retest under specified operating conditions ( Record tests and results )

Electrical Relationships EL

  • Voltage V = I × R Block D: 22 questions
  • Current I = V ÷ R
  • DC electrical power P = V × I
  • Ideal 24 V; 6 Ω 4 A load current
  • 24 V DC; 100 A 2,400 W electrical output
  • Series 12 V batteries 24 V nominal; compatible pair
  • Parallel 12 V batteries 12 V nominal; increased capacity

DTC vs Failure Cause EL

DTC

  • Reports detected condition
  • Guides diagnostic test selection

Cause

  • Established by measurements
  • May involve wiring or supply
  • Test before replacing named components

Electrical Diagnosis EL

  • Voltage drop Measure across path under prescribed load
  • Resistance mode De-energize; discharge; isolate parallel paths
  • No crank Battery, loaded paths, interlocks, command
  • Spark ignition Approved spark tester; supply/control checks
  • No communication Power, grounds, network; wiring diagram
  • DTC Detected condition; follow diagnostic tests

Drivetrain Checks DR

  • Clutch release OEM bearing travel and linkage checks Block E: 17 questions
  • Automatic-transmission fluid Level at specified temperature/conditions
  • AMT calibration After clutch replacement: specified calibration
  • Driveline vibration Ride height, angles, phasing, joints
  • Transfer case Distributes output to additional driven axles
  • Axle ratio Ring teeth ÷ pinion teeth
  • 41 ring; 10 pinion teeth 4.10:1 pinion-to-ring revolution ratio

Chassis and Wheel Checks CH

  • Steer-tire wear Inspect pressure, play, bearings, suspension Block F: 18 questions
  • Kingpin play Axle-specific loading, measurement, wear limits
  • Air ride height OEM dimension; pressure varies with load
  • Frame cracks Material/location-specific OEM repair procedure
  • Coupler play Check wear, mounts, positive lock
  • Multi-piece rim Trained service; restraint; outside trajectory
  • Rim heat Never heat or weld rim components
  • Wheel bearing Dial-indicator end play; hub-specific limits

Cab Checks CA

  • Seat drops Inspect pneumatic supply, controls, leakage Block G: 5 questions
  • Wiper stalls Check linkage binding and electrical supply
  • SRS service OEM isolation and capacitor discharge
  • Cab tilt Support and lock using OEM procedure

Trailer Checks TR

  • Landing gear Support trailer; inspect gearing/cross-shaft Block H: 8 questions
  • Reefer service Qualified technician; isolate automatic-start energy
  • Defrost Removes evaporator ice; restores airflow
  • Trailer structure Inspect corrosion, cracks, fasteners, flooring
  • Trailer lighting Check circuit, connectors, ground; applicable rules

Climate Checks CL

  • Evaporator Absorbs cab heat; refrigerant evaporates Block I: 7 questions
  • Condenser Rejects heat; refrigerant condenses
  • Low heater airflow Blower, filter, duct diagnosis
  • Low heater temperature Coolant flow, core, temperature controls
  • A/C recharge Identify refrigerant; recover; OEM charge

Hydraulic Pressure vs Flow HY

Pressure

  • Force per piston area
  • Load-related measurement

Flow

  • Speed × effective piston area
  • Measured under specified load
  • Pressure alone cannot establish delivered flow

Hydraulic Checks HY

  • Hydraulic force F = A × P Block J: 8 questions
  • Piston area A = 3.14 × r²
  • 50 mm bore; 10 MPa 19.625 kN ideal cap-end force π3.14; no losses/opposing pressure
  • Slow actuator Test delivered flow under specified load
  • Leak search Never use hands near pressure leaks
  • Injection injury Immediate emergency treatment; identify injected fluid

Energy Control HY

  • Identify → Isolate → Control → Verify
  • Identify: all energy sources Isolate: vehicle-specific procedure Control: stored-energy hazards Verify: rated equipment and PPE

High-Voltage Safety HY

  • Qualified HV technician Vehicle-specific training, rated tools, required PPE Block K: 4 questions
  • Isolation OEM high/low-voltage and charging isolation Hybrid engine sources also isolated
  • Discharge Observe vehicle-specific stored-energy discharge procedure
  • Verification Rated meter, required PPE; prove isolation

Common Traps

Ignition-off vs isolation

  • Ignition-off stops a command ≠ Isolation controls all hazardous energy

Zero air vs zero energy

  • Chamber air can be exhausted ≠ Spring still stores mechanical energy

Code vs failed component

  • Code reports a detected condition ≠ Tests establish the failure cause

Dryer vs dry reservoirs

  • Dryer removes most moisture ≠ Reservoir checks/draining remain specified

Stroke correction vs repair

  • Manual readjustment may hide excessive stroke ≠ Repair identified cause; verify stroke

Nominal vs measured voltage

  • Nominal voltage names the system ≠ Measured voltage depends on operating conditions

Last Minute

  • 1. 135 questions; four hours; 70% pass
  • 2. Electrical block: 22; engines: 21 questions
  • 3. Ontario: Truck and Coach Technician, 310T
  • 4. Loaded voltage-drop tests reveal unwanted resistance
  • 5. Resistance tests require de-energized, discharged circuits
  • 6. Regeneration burns soot; ash requires cleaning
  • 7. Spring-brake energy remains without air pressure
  • 8. Brake-stroke limits require chamber-specific test conditions
  • 9. Inspect wear before changing steering geometry
  • 10. Reefer service requires automatic-start energy isolation
  • 11. Hydraulic injection needs immediate emergency treatment
  • 12. Qualified HV work: isolate, discharge, verify
  • 13. Verify repairs under specified operating conditions

Red Seal Truck and Transport Mechanic (Interprovincial Exam)

  • Practice Questions 135 questions Study Guide 56 topics Cheat Sheet 79 facts Flashcards 50 cards Podcast