Cheat sheet

ICC M1 Residential Mechanical Cheat Sheet

Practice this exam

General Administration and Requirements

  • 10% of exam
  • Inspection Route Listing Access Approval

Heating, Cooling and Water Heaters

  • 24% of exam
  • Equipment Installation Heating and Cooling Boilers and Water Heaters Condensate

Exhaust and Ventilation Systems

  • 8% of exam
  • Exhaust Navigation M1505.5 Whole-House Air Makeup Air

Duct Systems

  • 8% of exam
  • Duct Check Return Air Garage Isolation Underfloor Plenum

Combustion Air

  • 16% of exam
  • Combustion-Air Path G2407 Free Area Interlock

Chimneys and Vents

  • 19% of exam
  • Chimney and Vent Check Vent Selection Type B Direct Vent

Fuel Supply Systems

  • 15% of exam
  • Gas Supply Check Gas Table Inputs G2413.4 Fuel Oil

Quick Facts

  • Exam ICC M1 Residential Mechanical Inspector
  • Edition 2024 IRC option
  • Questions 60 multiple-choice
  • Time 2 hours
  • Reference Open book; 2024 IRC
  • Pass 75 scaled score
  • Scoring Raw passing count varies by form
  • Largest area Heating/cooling/water heaters: 24%
  • Fuel scope Gas and oil systems

Code Lookup AD

  • LOCATE: location, occupancy, code, appliance, table, exception
  • Location Occupancy Code edition Appliance listing Table notes Exceptions

Scaled 75 vs Raw Percent AD

Scaled 75

  • ICC certification passing standard
  • Comparable across forms
  • Reported as pass/fail

Raw percent

  • Questions correct divided by total
  • Form-specific threshold
  • Not fixed at 45/60
  • 75 is not 75%

2024 IRC Section Picker AD

  • Equipment listing or access → Open M1302–M1307 ( Then appliance chapter )
  • Cooling condensate → Open M1411 ( Check location and disposal )
  • Dryer or cooking exhaust → Open M1502 or M1503 ( Then M1504 termination )
  • Air distribution or returns → Open M1601–M1602 ( Check exceptions )
  • Gas piping or combustion → Open G2407/G2413 ( Chapter 24 )
  • Oil storage or piping → Open Chapter 22 ( Fuel-oil scope )

Inspection Route AD

  • Chapter 1 Administrative adoption and permits
  • M1201 Mechanical administration scope
  • M1302 Appliance approval and listing
  • M1305 Service and replacement access
  • M1306 Combustible-clearance conditions
  • M1307 Listing and installation instructions
  • Inspection order Identify system before section lookup
  • Local amendment Check adopted jurisdiction text

Equipment Installation EQ

  • M1401 Heating/cooling installation
  • Equipment listing Match intended use and location
  • Manufacturer instructions Apply alongside IRC requirements
  • Service clearance Keep required access available
  • Garage appliance Check M1307 garage protections
  • M1411 Cooling condensate provisions
  • Condensate route Drain per applicable section
  • Safety control Verify installed required device

Heating and Cooling EQ

  • Furnace Check support, access, venting
  • Heat pump Check listed installation conditions
  • Cooling coil Check condensate management
  • Hydronic system Navigate Chapter 21 piping
  • Solar thermal Navigate Chapter 23
  • Fuel-fired appliance Check air and vent paths
  • Electric appliance Check applicable electrical provisions

Boilers and Water Heaters EQ

  • M2001 Boiler installation requirements
  • M2002 Boiler controls and safety
  • M2003 Expansion tank provisions
  • M2005 Water-heater installation
  • Potable connection Check Chapter 28 interface
  • Fuel connection Check Chapter 24 if gas
  • Relief protection Verify applicable discharge path

Local vs Whole-House Ventilation EX

Local exhaust

  • Bathroom/kitchen source
  • M1505.5 minimum rate
  • Discharge rules apply

Whole-house

  • Dwelling outdoor-air rate
  • M1505.4.3 area/bedrooms
  • Controls and runtime
  • One can serve both conditionally

Ventilation Decision EX

  • Bathroom local exhaust → Use M1505.5 ( 50 intermittent; 20 continuous cfm )
  • Kitchen local exhaust → Use M1505.5 ( 100 intermittent; 25 continuous cfm )
  • Whole-dwelling ventilation → Use M1505.4.3 ( Area/bedrooms and runtime )
  • Non-direct, non-mechanical-draft fuel appliance → Check >400cfm exhaust makeup ( Inside dwelling air barrier; M1503.6 )
  • Exhaust termination near intake → Use M1504.3 ( Check listed exceptions )

Exhaust Navigation EX

  • M1501 Mechanical exhaust outdoors
  • M1502 Clothes-dryer exhaust
  • M1503 Domestic cooking exhaust
  • M1504 Ducts and termination openings
  • M1505 Local and whole-house ventilation
  • Bathroom exhaust Outdoors; no indoor recirculation
  • Ductless hood Only permitted M1503.3 exception
  • M1504.3 Check opening separation exceptions

Ventilation Rates EX

  • M1505.5 bathroom 50 intermittent; 20 continuous cfm
  • M1505.5 kitchen 100 intermittent; 25 continuous cfm
  • Bath fan rating Check required static-pressure basis
  • M1505.4.3 Whole-house area/bedroom rate table
  • Intermittent whole-house ≥25% each 4h; apply factor
  • M1505.4.2 Manual override control
  • M1503.6 Makeup air; qualifying trigger only

Supply vs Return Plenum DU

Supply plenum

  • Delivers conditioned air
  • Building cavities barred
  • Check M1601.1.1

Return plenum

  • Collects return air
  • Some cavities conditional
  • Check sealing and exclusions
  • Cavity permission differs

Duct Check DU

  • M1601.1 Design and approved installation method
  • UL 181 ducts Listed factory-made ducts
  • Joint closure Manufacturer-approved sealing system
  • M1601.4.2 Metal lap follows airflow
  • M1601.5 New underfloor plenums prohibited
  • Existing underfloor Check repair-specific conditions
  • Garage HVAC No shared dwelling supply/return
  • M1602.2 Return openings; check exceptions

Combustion Air CO

  • AIR: appliance, intake, restrictions
  • Appliance inputs Intake method Restrictions and interlocks

Indoor vs Outdoor Combustion Air CO

Indoor path

  • Available room volume
  • Infiltration condition
  • G2407 calculations

Outdoor path

  • Opening method
  • Net free area
  • Louver effects
  • Choose method before sizing

Air and Vent Decision CO

  • Fuel-gas appliance installed → Check G2407 air ( Select authorized method )
  • Indoor-air method chosen → Verify volume and infiltration ( Use correct calculation )
  • Outdoor opening chosen → Size net free area ( Account for louver )
  • Motorized combustion-air opening → Provide required interlock ( Appliance cannot run closed )
  • Direct-vent appliance → Follow listed vent assembly ( Use manufacturer termination )

Combustion-Air Path CO

  • G2407 Fuel-gas combustion-air methods
  • Indoor air Check volume and infiltration
  • Outdoor air Select compliant opening method
  • Appliance input Sum relevant fuel loads
  • Net free area Account for grille/louver rating
  • Motorized louver Interlock appliance operation
  • Blocked opening No assumed available airflow
  • Mechanical ventilation Check interaction with combustion

Venting Path VE

  • VENT: verify appliance, exhaust category, notes, termination
  • Appliance type Vent category Listing notes Termination

Type B vs Direct Vent VE

Type B

  • Listed gas vent
  • Eligible appliances only
  • Check clearance/termination

Direct vent

  • Listed appliance assembly
  • Dedicated air and exhaust
  • Follow manufacturer termination
  • Listing governs selection

Chimney and Vent Check VE

  • R1003 Masonry chimney construction
  • R1005 Factory-built chimney listing
  • M1801 Venting general requirements
  • Liner Match fuel and appliance
  • Unused opening Close or cap
  • Vent support Carry system weight
  • Duct/plenum No vent penetration through air path
  • Direct vent Follow appliance listing and instructions

Masonry vs Factory-Built Chimney VE

Masonry

  • R1003 construction
  • Compatible lining
  • Clearance by location

Factory-built

  • R1005 installation
  • Listed assembly
  • Manufacturer clearances
  • Construction rules differ

Vent Selection VE

  • G2427 Fuel-gas venting path
  • G2428 Vent-sizing provisions
  • Category I Check listed vent sizing
  • Category IV Use listed pressure-tight vent system
  • Type B Check appliance and vent listing
  • Single-wall Check location and clearance limits
  • Connector Material and routing conditions
  • Termination Check type-specific location rules
  • Common vent Check eligible appliance combinations

Gas Sizing Memory FU

  • GASP: gas, assumptions, section, path
  • Gas heating value Assumed pressure/drop/SG Section demand Path length

Gas vs Fuel-Oil Supply FU

Fuel gas

  • Chapter 24
  • Pipe sizing and pressure
  • G2413/G2417

Fuel oil

  • Chapter 22
  • Tank and piping
  • M2201/M2202
  • Navigate fuel-specific chapter

Gas Pipe Table Picker FU

  • Connected appliances listed → Total section Btuh ( Include downstream loads )
  • Heating value known → Convert Btuh to CFH ( Use actual gas value )
  • Sizing method selected → Determine applicable path length ( G2413.4 method )
  • Schedule 40 natural gas → Check G2413.4(1) ( SG .60; <2psi; .5in drop )
  • Conditions differ from table → Select matching table/method ( Never transfer capacity blindly )
  • Installed gas pipe → Check G2417 test ( Before acceptance )

Gas Table Inputs FU

  • G2413 Gas pipe sizing framework
  • Load conversion Btuh divided by gas heating value
  • Section demand Sum connected downstream input
  • G2413.4(1) Schedule 40 metallic gas table
  • Table gas Natural gas; SG 0.60
  • Table pressure Inlet below 2 psi
  • Table drop 0.5 inch water column
  • Table length Use selected method/path length
  • Capacity Match diameter to required CFH
  • Different conditions Choose corresponding table or method

Gas and Oil Controls FU

  • G2417 Gas pressure-test provisions
  • G2420 Accessible appliance shutoffs
  • G2422 Appliance connection provisions
  • Unused gas outlet Cap or plug safely
  • Material transition Use listed compatible fittings
  • M2201 Fuel-oil tank installations
  • M2202 Fuel-oil piping provisions
  • Oil fill/vent Check Chapter 22 conditions

Common Traps

Score interpretation

  • 75 scaled score ≠ 75% raw correctness

Edition choice

  • 2024 IRC option ≠ Older IRC section text

Local versus whole

  • M1505.5 local exhaust ≠ M1505.4.3 whole-house rate

Makeup-air trigger

  • Qualifying appliance plus >400cfm exhaust ≠ Every large hood unconditionally

Garage air path

  • Shared dwelling HVAC prohibited ≠ Dedicated garage system conditional

Category IV vent

  • Listed pressure-tight vent assembly ≠ Generic PVC assumption

Gas table transfer

  • Match length, pressure, SG, material ≠ Reuse unrelated table capacity

Venting exception

  • Check appliance listing and exception ≠ Assume universal termination distance

Last Minute

  • 1. M1: 60MCQ; 2h; open-book
  • 2. Pass: 75 scaled, not 45/60
  • 3. Administration: 10%; equipment: 24%
  • 4. Exhaust: 8%; ducts: 8%
  • 5. Combustion air: 16%; vents: 19%
  • 6. Fuel supply: 15%
  • 7. Match 2024 IRC exam edition
  • 8. M1307: listing and installation instructions
  • 9. M1411: cooling condensate conditions
  • 10. Bathroom: 50cfm intermittent; 20cfm continuous
  • 11. M1505.4.3: whole-house area/bedrooms
  • 12. M1602.2: return-air exceptions matter
  • 13. G2407: choose combustion-air method first
  • 14. G2427: appliance-specific vent route
  • 15. G2413.4: match every table assumption
  • 16. G2417: pressure-test requirements
  • 17. Chapter 22 covers fuel oil

ICC Residential Mechanical Inspector (M1)

  • Practice Questions 150 questions Study Guide 31 topics Cheat Sheet 96 facts Flashcards 50 cards 1 Job Wiki Free CE Podcast