Cheat sheet

ICC Residential Plumbing Inspector (P1) Cheat Sheet

Practice this exam

General Requirements

  • 14% of exam
  • Permits Piping Protection Installation & Support Building Damage Testing

Fixtures

  • 8% of exam
  • Locations Materials & Approvals Installation & Clearances Flow Rates & Temps Faucet Fittings

Water Heaters

  • 12% of exam
  • Installation T&P Relief Valve Discharge Piping Thermal Expansion Fuel Gas & Venting

Water Supply and Distribution

  • 21% of exam
  • Materials & Joints Sizing Backflow Prevention Pressure & Volume Water Treatment

Sanitary Drainage

  • 23% of exam
  • DFU Loading Pipe Sizing & Slope Cleanouts Traps Indirect Waste

Vents

  • 22% of exam
  • Materials & Grades Sizing Trap-to-Vent Distance Wet & Circuit Vents AAVs

Quick Facts

  • Exam ID P1, Residential Plumbing Inspector
  • Questions 60 multiple-choice
  • Time Limit 2 hours
  • Format Open book
  • Passing Score Scaled score of 75
  • Code Basis 2024 IRC, Chapters 25-33
  • Validity 3 years
  • Delivery Pearson VUE or ICC PRONTO

IRC Plumbing Chapter Range GE

  • Plumbing lives in IRC Chapters 25 through 33
  • 25 Admin 26-27 Fixtures 28 Heaters 29 Supply 30 Drainage 31 Vents

DWV Water Test vs Air Test GE

DWV Water Test

  • 10 ft head minimum
  • Hold 15 minutes

Water Supply Air Test

  • 50 psi minimum
  • Hold 15 minutes
  • Match the test method to system

Testing & Permit Thresholds GE

  • DWV water test 10 ft head, hold 15 min
  • Water supply air test 50 psi min, hold 15 min
  • Permit required example water heater replacement
  • Permit exempt example clearing stoppages, stopping leaks
  • Notch limit 2x6 stud 25 percent depth, 1-3/8 in
  • Bore limit bearing stud 40 percent of stud depth
  • Firestop requirement approved system at fire wall
  • Modification authority building official grants in writing
  • Sleeve at foundation allows movement, seals water entry

Fixture Clearances & Approvals FI

  • Water closet side clearance 15 in minimum from obstruction
  • Water closet centerline spacing 30 in minimum apart
  • Water closet front clearance 21 in minimum clear space
  • Fixture approval basis listing, labeling, material standard
  • Flow rate control max and min rates verified
  • Temperature limiting control at fixture, not heater thermostat

Seismic Strap Memory Aid WA

  • Upper third and lower third with four inches over controls
  • Upper 1/3 Lower 1/3 4 in above controls SDC D0-D2 + C townhouse

Water Heater Safety Check WA

  • T&P valve installed → Verify no isolation valve
  • Discharge pipe routed → Check 6 in max height ( no threads, rigid pipe )
  • SDC D0-D2 or C townhouse → Require seismic strapping
  • Storage tank in attic → Require an approved drain pan

Water Heater Safety Rules WA

  • T&P valve isolation never permitted between tank
  • T&P discharge height 6 in max above floor
  • T&P discharge threads not permitted on end
  • T&P discharge pipe rigid, no valve or trap
  • Drain pan trigger where leakage could damage building
  • Seismic strap zones SDC D0-D2 plus C townhouse
  • Seismic strap points upper third and lower third
  • Lower strap clearance 4 in above controls
  • Thermal expansion trigger closed system, check valve present

Air Gap vs Backflow Preventer WA

Air Gap

  • Physical separation
  • No moving parts
  • Visual verification

Mechanical Backflow Preventer

  • Compact, in-line device
  • Needs periodic testing
  • Fits tight spaces
  • Use air gap when space allows

Backflow Protection Selection WA

  • Direct cross-connection, high hazard → Reduced pressure principle assembly ( continuous pressure use )
  • Air gap achievable at fixture → Install approved air gap ( 2x opening, 1 in min )
  • Hose bibb outdoor connection → Atmospheric vacuum breaker
  • Boiler with chemical treatment → Air gap or RP assembly
  • Irrigation system connection → Device per Table P2902.3

Water Supply & Backflow Rules WA

  • Static pressure limit over 80 psi needs PRV
  • Air gap sizing 2x opening, 1 in min
  • Backflow device table Table P2902.3 by hazard
  • Backsiphonage cause supply pressure drops below
  • Backpressure cause downstream pressure exceeds supply
  • Water hammer fix arrestor near quick-closing valve
  • Hose bibb protection atmospheric vacuum breaker required

Backsiphonage vs Backpressure WA

Backsiphonage

  • Supply pressure drops
  • Vacuum pulls water back

Backpressure

  • Downstream pressure rises
  • Pushes water upstream
  • Match the device to the mechanism

DFU Quick Recall SA

  • Lav one, sink two, tub two, WC three or four
  • Lav 1 Sink 2 Tub 2 WC 3-4

S-Trap vs P-Trap SA

S-Trap

  • Self-siphons on discharge
  • Prohibited configuration

P-Trap

  • Vented trap arm
  • Code-compliant design
  • S-trap is prohibited unvented risk

Cleanout Placement Decision SA

  • Building drain meets sewer → Cleanout required at junction
  • Horizontal branch, 2+ fixtures → Cleanout at the junction
  • Direction change over 45 deg → Cleanout at that bend
  • Multiple bends within 40 ft → One cleanout serves all
  • Long straight horizontal run → Cleanout every 100 ft

Drainage Fixture Unit Values SA

  • Water closet, 1.6 gpf 3 DFU
  • Water closet, other 4 DFU
  • Lavatory 1 DFU
  • Bathtub or shower 2 DFU
  • Kitchen sink 2 DFU
  • Clothes washer standpipe 2 DFU

Drainage Slope & Cleanout Sizing SA

  • Slope, 2.5 in or less 1/4 in per ft
  • Slope, 3 in or more 1/8 in per ft
  • Cleanout max interval 100 ft horizontal run
  • Cleanout direction change required over 45 degrees
  • Multiple bends in 40 ft one cleanout serves all
  • Backwater valve trigger rim below upstream manhole

Traps & Indirect Waste SA

  • Trap seal depth 2 in min, 4 in max
  • S-trap status prohibited, self-siphons
  • Water closet trap size 3 in minimum, no exceptions
  • Indirect waste protection air break or air gap

Trap Arm Growth Pattern VE

  • Bigger trap arm allows a longer run to the vent
  • 1-1/4 in = 30 in 1-1/2 in = 42 in 2 in = 60 in 3 in = 72 in

Wet Vent vs Circuit Vent VE

Wet Vent

  • Drain also vents fixtures
  • Limited to bathroom group

Circuit Vent

  • Vents a fixture battery
  • Serves a horizontal branch
  • Both need an exact arrangement

Trap-to-Vent Distance Check VE

  • Trap arm is 1-1/4 in → Max 30 in to vent
  • Trap arm is 1-1/2 in → Max 42 in to vent
  • Trap arm is 2 in → Max 60 in to vent
  • Trap arm is 3 in → Max 72 in to vent

Vent Sizing & Trap-Arm Distance VE

  • Min vent pipe size 1-1/4 in minimum
  • Vent-to-drain ratio at least half drain diameter
  • Trap arm, 1-1/4 in 30 in max to vent
  • Trap arm, 1-1/2 in 42 in max to vent
  • Trap arm, 2 in 60 in max to vent
  • Trap arm, 3 in 72 in max to vent

AAV vs Open Vent VE

Air Admittance Valve

  • Admits air only
  • Mechanical, needs access

Open Vent

  • Two-way air path
  • Connects to outdoors
  • AAV never fully replaces open vent

Vent Terminals & Vent Types VE

  • Vent terminal height 6 in above roof surface
  • Snow climate vent 6 in above snow line
  • Terminal near opening 10 ft, or 3 ft above
  • Wet vent scope bathroom group, one floor
  • AAV limitation no positive-pressure relief path
  • Common vent condition method-specific fixture arrangement only

Common Traps

Confusing Trap Seal Limits

  • Minimum seal is 2 inches ≠ Maximum seal is 4 inches

S-Trap Looks Like P-Trap

  • S-trap self-siphons and fails ≠ P-trap with vent holds seal

Two Different Test Standards

  • DWV test needs 10 ft head ≠ Air test needs 50 psi minimum

Mixing Up Backflow Mechanisms

  • Backsiphonage is a pressure drop ≠ Backpressure is a pressure push

Assuming AAV Replaces Open Vent

  • AAV only admits air in ≠ System still needs outdoor vent

Slope Ratio Varies By Size

  • 2.5-in pipe needs 1/4 slope ≠ 3-in pipe needs 1/8 slope

Cleanout Rule Depends On Layout

  • Straight runs cleanout every 100 ft ≠ Bend over 45 deg needs cleanout

Last Minute

  • 1. Exam is 60 questions total
  • 2. Time limit is two hours
  • 3. Exam is open book format
  • 4. Passing score is 75 scaled
  • 5. Trap seal range is 2-4 in
  • 6. Min vent size 1-1/4 in
  • 7. Pressure over 80 psi needs PRV
  • 8. Cleanouts required every 100 feet
  • 9. T&P valve must never be isolated
  • 10. Bring only approved code references
  • 11. Tab your IRC before exam day
  • 12. Six attempts allowed per six months

ICC Residential Plumbing Inspector (P1)

  • Practice Questions 100 questions Study Guide 18 topics Cheat Sheet 59 facts Flashcards 50 cards Blogs 1 blog 1 Job Wiki Free CE Podcast