Cheat sheet

IMSA Traffic Signal Technician I Cheat Sheet

Practice this exam

Signal Operations & Indications

  • Not published of exam
  • NEMA Phases Ring-Barrier Signal Timing Pedestrian Intervals Signal Heads Preemption

Cabinet Wiring & Components

  • Not published of exam
  • Load Switches Conflict Monitor Controller Terms Electrical Basics Flasher Unit

Vehicle Detection

  • Not published of exam
  • Inductive Loops Video Detection Microwave Radar Pushbuttons Detector Testing

Installation & Maintenance

  • Not published of exam
  • Signal Supports Pull Boxes Troubleshooting Preventive Maintenance

Standards & Legal Requirements

  • Not published of exam
  • MUTCD NEC Signal Warrants Liability

Communications Systems

  • Not published of exam
  • Fiber Optic Copper Interconnect Wireless Ethernet

Safety

  • Not published of exam
  • LOTO PPE OSHA Work Zone

Quick Facts

  • Exam IMSA TST-I
  • Credential Traffic Signal Technician I
  • Questions 50 multiple-choice
  • Time 3 hours
  • Pass 70%
  • Format Online proctored
  • Level Entry-level
  • Prereq Work Zone cert + 1 yr exp

NEMA Phase Numbering SI

  • Evens = through, odds = left
  • 2/6: major through 1/5: major left 4/8: minor through 3/7: minor left

Gap Out vs Max Out SI

Gap Out

  • No call within passage time
  • Efficient early termination

Max Out

  • Hits maximum green cap
  • Forced by conflicting demand
  • Efficient end vs forced end

NEMA Phases & Ring-Barrier SI

  • Phase 2/6 Major street through movements
  • Phase 1/5 Major street left turns
  • Phase 4/8 Minor street through movements
  • Phase 3/7 Minor street left turns
  • Ring Phases that time sequentially
  • Barrier Point both rings cross together
  • Concurrent phases Different rings, same time
  • Phase Timed right-of-way, one movement

Signal Cycle Sequence SI

  • Green -> Yellow -> All-Red -> Next Green
  • Green: right of way Yellow: warning end All-red: clear vehicles Next: conflicting green

Yellow Change vs All-Red SI

Yellow Change

  • Warns approaching drivers
  • 3-6 seconds typical

All-Red / Clearance

  • Clears entered vehicles
  • Follows yellow, optional
  • Warn vs clear

Signal Timing Intervals SI

  • Min green Shortest allowed green time
  • Max green Green cap with conflicting call
  • Yellow change 3-6 sec warning interval
  • All-red / red clearance Extra clearance after yellow
  • Passage time Extends green per vehicle detected
  • Gap out No call within passage time
  • Max out Forced end at max green
  • Cycle length 60-180 sec, one full sequence
  • Split % of cycle per phase
  • Dwell/rest Holds green, no conflicting call

Leading vs Lagging Left Turn SI

Leading Left

  • Arrow before through green
  • Clears queue first

Lagging Left

  • Arrow after through green
  • Less common sequence
  • Before vs after through

Pedestrian Signal Intervals SI

  • Walk Steady white walking person
  • Pedestrian clearance (FDW) Flashing upraised hand, finish crossing
  • Walking speed 3.5 ft/sec MUTCD default
  • Pushbutton Places pedestrian call, not instant
  • Ped recall Walk served every cycle
  • Mount height 7-10 ft above sidewalk

Preemption vs Priority SI

Preemption

  • Immediately overrides timing
  • Trains, emergency vehicles

Priority

  • Adjusts timing only
  • Transit, does not override
  • Override vs adjust

Signal Heads & Indications SI

  • Vertical head order Red top, yellow, green bottom
  • Green ball Permissive, yield when turning
  • Green arrow Protected, exclusive movement only
  • Flashing red Stop, treat as stop sign
  • Flashing yellow Proceed with caution
  • FYA Flashing yellow arrow, permissive left
  • Backplate Cuts sun phantom glare
  • Visor/hood Shields lens from sunlight
  • Min signal faces 2 per approach, MUTCD
  • Lens size 12-inch standard, 11th Edition

Preemption & Priority SI

  • Preemption Interrupts timing for train/EMS
  • Opticom Optical emitter/receiver EMS preemption
  • Railroad preemption Highest priority, overrides EMS
  • Priority Adjusts timing, does not override

Conflict Monitor vs MMU CA

Conflict Monitor

  • TS 1 cabinets
  • Basic conflict detection

MMU

  • TS 2 cabinets
  • Broader fault detection, SDLC
  • Both force flash on fault

Recall Mode Picker CA

  • Main street coordinated phase → Max recall ( Times to max every cycle )
  • Side street, low volume → Min recall or none ( Serves only on call )
  • Crosswalk needs guaranteed walk → Pedestrian recall
  • No detectors on approach → Recall required for service

Cabinet Components CA

  • Load switch Switches AC power per indication
  • Flasher unit Alternates power for flash mode
  • Flash transfer relay Switches controller to flasher
  • Conflict monitor / MMU Detects conflicts, forces flash
  • Police panel Manual phase/flash control
  • GFI/GFCI Trips on ~5mA ground fault
  • Surge protector Shields electronics from spikes
  • Circuit breaker Opens circuit on overcurrent
  • Detector rack Houses loop amplifier cards

Controller Operation Terms CA

  • Call/demand Request for phase service
  • Recall Phase placed in demand always
  • Max recall Forces max green every cycle
  • Actuated signal Detector input varies timing
  • Semi vs full actuated Minor-only vs all-approach detectors
  • NEMA TS1 Legacy conflict monitor standard
  • NEMA TS2 MMU + serial bus standard

Electrical Fundamentals CA

  • Ohm's Law V = I x R
  • Power formula P = V x I
  • Series resistance Sum of all resistors
  • Parallel resistance Always less than smallest resistor
  • Signal voltage 120 VAC standard operating
  • AC frequency 60 Hz in US
  • Voltage drop IxR loss along cable run
  • Megger test Checks cable insulation resistance
  • Multimeter Measures volts, amps, ohms
  • 80% continuous rule Derate breaker for 24/7 loads

Detection Technology Family VE

  • Loop = embedded, video/radar = above ground
  • Loop: in-pavement wire Video: camera pixels Radar: reflected microwave Pushbutton: pedestrian call

Loop vs Video Detection VE

Inductive Loop

  • In-pavement wire
  • Requires saw cut

Video Detection

  • Camera-based, non-intrusive
  • Weather/lighting sensitive
  • Embedded vs above-ground

Detector Selection Picker VE

  • Stop-line, in-pavement detection → Inductive loop ( 6x6 quadrupole )
  • Multi-lane, non-intrusive, cameras ok → Video detection ( Weather-sensitive )
  • Above-ground, speed + presence → Microwave/radar detector ( Non-intrusive )
  • Pedestrian crossing demand → Pushbutton ( Places a call )
  • Insulation resistance test needed → Megger (megohm meter)

Detection Technologies VE

  • Inductive loop Senses inductance change, in-pavement
  • Video detection Analyzes pixel change, non-intrusive
  • Microwave/radar Reflects signal, speed + presence
  • Pedestrian pushbutton Detector placing pedestrian call
  • Detector amplifier Converts loop signal to call

Signal Cable vs Loop Lead-In VE

Signal/Interconnect Cable

  • IMSA Spec 19-1/20-1
  • Head + interconnect wiring

Loop Lead-In

  • IMSA Spec 50-2
  • Shielded twisted pair, detector
  • Different cable, different job

Loop Detector Details VE

  • 6x6 quadrupole Standard stop-line loop shape
  • Sensitivity Threshold for triggering detection
  • Common failure Pavement cracks break loop wire
  • Loop lead-in IMSA Spec 50-2 cable
  • Signal/interconnect cable IMSA Spec 19-1 or 20-1

Troubleshooting Order IN

  • Power -> controller -> load switch -> field -> head
  • Power: check first Controller: logic + timing Load switch: field power Head: last check

Dark Signal vs Flash Mode IN

Dark Signal

  • Total power loss
  • Treat as all-way stop

Flash Mode

  • Intentional or fault-triggered
  • Main yellow, side red
  • No power vs controlled state

Field Troubleshooting Picker IN

  • All signals dark → Check power at cabinet first
  • Intersection stuck in flash → Check conflict monitor fault log
  • Coordination lost between intersections → Check interconnect + baud settings
  • Loop gives false or no calls → Check sensitivity, then megger test
  • Signal knocked down by vehicle → Secure scene, add traffic control

Signal Supports & Installation IN

  • Mast arm Cantilevered structural signal support
  • Span wire Cable-suspended signal mounting
  • Strain pole Anchors span wire tension
  • Pull box/handhole Underground cable access point
  • Drip loop Prevents water tracking into equipment
  • Head aiming Aligns to approaching driver view
  • Foundation check Verify depth, rebar, conduit stub

Maintenance & Troubleshooting IN

  • Dark signal Total power loss, all out
  • Troubleshoot order Power, controller, load switch, field
  • LED maintenance Clean lens, check luminance
  • Preventive maintenance Scheduled inspection before failure
  • Knockdown procedure Secure, control traffic, document
  • Conduit fill Max ~40% cross-section filled

MUTCD Statement Hierarchy ST

  • Standard shall, Guidance should, Option may
  • Standard: mandatory Guidance: recommended Option: permissive Support: informational

MUTCD Essentials ST

  • MUTCD Manual on Uniform Traffic Control Devices
  • Standard Mandatory, uses word 'shall'
  • Guidance Recommended, uses word 'should'
  • Option Permissive, uses word 'may'
  • Support Informational background only
  • Part 4 Highway Traffic Signals section
  • 9 signal warrants Justify further engineering study
  • 11th Edition Current MUTCD, effective 2024

NEC & Legal Requirements ST

  • NEC Article 250 Grounding and bonding rules
  • Ground wire color Green or green/yellow stripe
  • Ground rod max 25 ohms resistance or less
  • Documentation Protects agency from liability
  • Prerequisite cert IMSA Work Zone Technician required

Communications Media Picker CO

  • Long-haul, high bandwidth corridor → Single-mode fiber
  • Short cabinet-to-cabinet link → Copper twisted-pair
  • No trenching feasible → Wireless interconnect
  • Verify fiber break location → OTDR test
  • Devices won't communicate → Match baud rate + address

Communications Media CO

  • Interconnect Shares coordination data between controllers
  • Single-mode fiber Long-haul, high-bandwidth preferred
  • Copper twisted-pair Short-distance interconnect cable
  • Wireless interconnect Avoids trenching new cable
  • Field master Coordinates local controllers, closed-loop
  • Baud rate Serial data speed, bits/sec
  • OTDR Locates fiber breaks, measures loss
  • Ethernet IP comms among cabinet devices

Safety Practices SA

  • LOTO Prevents unexpected re-energization
  • PPE Insulated gloves rated for voltage
  • OSHA Occupational Safety and Health Administration
  • Work zone setup First step before any work
  • Class C extinguisher Rated for electrical fires
  • Live wire on cabinet Do not touch, call utility

Common Traps

Standard ≠ Guidance

  • Standard means shall, mandatory ≠ Guidance means should, recommended

Conflict monitor ≠ timing device

  • Only detects unsafe conflicts ≠ Never sets or counts time

Green ball ≠ green arrow

  • Ball is permissive, yield turning ≠ Arrow is protected, exclusive

Dark signal ≠ flashing signal

  • Dark means total power loss ≠ Flash can be intentional or fault

Gap out ≠ max out

  • Gap out ends early, efficient ≠ Max out forced by max green

Loop lead-in ≠ signal cable

  • Lead-in is Spec 50-2 ≠ Signal cable is Spec 19-1/20-1

Right turn on red ≠ universal

  • Varies by state/jurisdiction ≠ No Turn on Red overrides

Preemption ≠ priority

  • Preemption overrides normal timing ≠ Priority only adjusts timing

Last Minute

  • 1. 50 questions, 3 hours, 70% pass
  • 2. Even phases = through movements
  • 3. Odd phases = left turns
  • 4. Conflict monitor forces flash mode
  • 5. Gap out efficient, max out forced
  • 6. Green ball permissive, arrow protected
  • 7. Standard = shall, Guidance = should
  • 8. Loop = in-pavement, video = camera
  • 9. NEC Article 250 = grounding
  • 10. LOTO before any cabinet work
  • 11. Ground wire green or green/yellow
  • 12. Fiber preferred for long-haul comms

IMSA Traffic Signal Technician Level I

  • Practice Questions 160 questions Study Guide 16 topics Cheat Sheet 114 facts Flashcards 50 cards Shorts 1 short 1 Job Wiki Free CE Podcast

Same family resources

  • Explore More IMSA Traffic Signal Technician
  • Continue into nearby exams from the same family. Each card keeps practice questions, study guides, flashcards, videos, and articles in one place.

IMSA Traffic Signal Field Technician Level II

  • Cheat Sheet 174 facts Practice Questions 124 questions Study Guide 41 topics Flashcards 50 cards 1 Job Wiki Free CE

IMSA Traffic Signal Senior Field Technician Level III

  • Practice Questions 124 questions Study Guide 55 topics 1 Job Wiki Free CE

IMSA Traffic Signal Bench Technician Level II

  • Practice Questions 100 questions 1 Job Wiki Free CE

IMSA Traffic Signal Construction Technician Level II

  • Practice Questions 100 questions Shorts 1 short Free CE

IMSA Traffic Signal Inspector

  • Practice Questions 100 questions Free CE