Cheat sheet

ASTM NCATT AET Cheat Sheet

Practice this exam

Electrical and Electronic Fundamentals

  • Not published of exam
  • DC circuits AC circuits Components Semiconductors Digital logic

Maintenance Practices and Measurement

  • Not published of exam
  • Safety ESD Tools Test equipment Technical data

Aircraft Wiring and Fundamentals

  • Not published of exam
  • Wiring Connectors Aircraft axes Flight controls Ground handling

Quick Facts

  • Credential Aircraft Electronics Technician
  • Administrator SpaceTEC Partners
  • Questions 90
  • Passing score 73%
  • Time limit Not published
  • Content weights Not published
  • Eligibility Open to all
  • Renewal Five years

AC Phase Memory EL

  • ELI: voltage leads; ICE: current leads
  • Inductor Capacitor

Series vs Parallel EL

Series

  • One current path
  • Current stays equal

Parallel

  • Multiple current paths
  • Voltage stays equal
  • Trace paths before choosing formula

DC Circuit Laws EL

  • Ohm law E equals I times R Core
  • Power P equals E times I
  • Series current Same through every component
  • Parallel voltage Same across every branch
  • Series resistance Add individual resistance values
  • Parallel resistance Total is branch-lower
  • KVL Loop voltage sum equals zero

Power Recall EL

  • Power equals volts times amps
  • P equals EI Watts

AC vs DC EL

DC

  • One polarity direction
  • Steady circuit analysis

AC

  • Direction periodically reverses
  • Phase may matter
  • Identify waveform and measurement needed

AC Circuit Essentials EL

  • Frequency Cycles per second Hz
  • RMS voltage Effective sine-wave value
  • Inductive reactance Rises with frequency
  • Capacitive reactance Falls with frequency
  • Inductor phase Voltage leads current ELI
  • Capacitor phase Current leads voltage ICE
  • Resonance Inductive equals capacitive reactance

Passive Components EL

  • Resistor Limits current flow R
  • Capacitor Stores electric field energy C
  • Inductor Stores magnetic field energy L
  • Transformer Transfers AC magnetic energy
  • Fuse Opens during excessive current
  • Circuit breaker Resettable overcurrent protection
  • Relay Electrically controlled switch

Active Devices and Logic EL

  • Diode Conducts primarily one direction
  • Transistor Controls current or switches
  • Rectifier Converts AC toward DC
  • AND gate All inputs true Logic
  • OR gate Any input true Logic
  • NOT gate Inverts input state Logic
  • Hexadecimal Base sixteen number system

Safe Test Order MA

  • Data, safe, measure, repair, verify
  • Approved data Verification

Voltage vs Current Test MA

Voltage

  • Measure across points
  • Circuit usually energized

Current

  • Measure through path
  • Meter goes series
  • Never use current range across source

Circuit Fault Check MA

  • Before touching circuit → Read current approved data ( Confirm configuration )
  • Hazard exists → Make system safe ( Use required controls )
  • Power is required → Select correct meter function ( Protect meter )
  • Supply is absent → Check source and protection ( Do not bypass )
  • Supply is present → Trace toward failed load ( Use diagrams )
  • Path is suspect → De-energize for resistance ( Avoid live ohms )
  • Fault is found → Repair per approved data ( Use proper materials )
  • Repair is complete → Functionally verify system ( Record required work )

Safe Maintenance Practice MA

  • Approved data Use current authorized instructions Always
  • ESD control Protect static-sensitive devices
  • FOD control Account for tools and debris
  • Lockout Control hazardous energy
  • PPE Match equipment to hazard
  • Hazardous material Follow handling requirements
  • Work area Keep clean and organized

Continuity vs Resistance MA

Continuity

  • Checks conductive path
  • Often audible indication

Resistance

  • Measures opposition value
  • Requires de-energized circuit
  • Remove power before either test

Measurement and Troubleshooting MA

  • Meter range Start safely when uncertain
  • Continuity Tests intended conductive path
  • Voltage test Measure across two points
  • Current test Place meter in series
  • Resistance test De-energize before measuring
  • Signal tracing Follow input through output
  • Fault isolation Verify before replacing parts

Flight Axes AI

  • Pitch, roll, yaw: three rotations
  • Lateral Longitudinal

Bonding vs Shielding AI

Bonding

  • Creates electrical path
  • Controls potential differences

Shielding

  • Limits noise coupling
  • Protects signal integrity
  • Use approved wiring data

Wiring Defect Response AI

  • Damage is observed → Stop and assess ( Prevent further damage )
  • Data identifies limits → Apply approved repair ( Follow exact method )
  • Chafing is present → Correct routing and protection ( Remove root cause )
  • Terminal is suspect → Inspect crimp and retention ( Use approved tools )
  • Connector is opened → Inspect pins and keying ( Prevent mis-mating )
  • Shield is disturbed → Restore continuity correctly ( Follow data )
  • Repair is finished → Inspect before energizing ( Look for FOD )
  • System is restored → Test and document ( Close maintenance record )

Aircraft Wiring Practice AI

  • Wire gauge Higher AWG means smaller
  • Crimp Use approved tooling
  • Strain relief Prevent terminal loading
  • Bonding Provides low-resistance path
  • Shielding Reduces electromagnetic interference
  • Connector keying Prevents wrong mating
  • Wire routing Avoid heat and chafing

Aircraft Fundamentals AI

  • Pitch Rotation about lateral axis
  • Roll Rotation about longitudinal axis
  • Yaw Rotation about vertical axis
  • Ailerons Primary roll control
  • Elevator Primary pitch control
  • Rudder Primary yaw control
  • Ground handling Follow aircraft-specific procedures

Common Traps

Live Resistance Test

  • Ohms needs de-energized circuit ≠ Protect meter and equipment

Unapproved Repair Data

  • Generic advice is insufficient ≠ Use current authorized instructions

Wrong Meter Jacks

  • Confirm lead positions ≠ Check function before contact

Bypassing Protection

  • Never defeat protective devices ≠ Find the underlying fault

Ignoring Chafing Cause

  • Repair damage and routing ≠ Prevent repeated contact

Assuming Published Weights

  • ASTM publishes no percentages ≠ Review all guide areas

Last Minute

  • 1. Recall Ohm law relationships
  • 2. Separate series from parallel
  • 3. Use ELI and ICE
  • 4. Identify passive component functions
  • 5. Recognize basic logic gates
  • 6. De-energize before resistance tests
  • 7. Check meter leads and range
  • 8. Use current approved maintenance data
  • 9. Protect ESD-sensitive components
  • 10. Inspect routing for chafing
  • 11. Match controls with axes
  • 12. Verify repair and documentation

ASTM NCATT Aircraft Electronics Technician (AET)

  • Practice Questions 126 questions Study Guide 28 topics Cheat Sheet 56 facts Flashcards 50 cards Shorts 3 short s Free CE