Cheat sheet

NCCCO Mobile Crane Cheat Sheet

Practice this exam

Site

  • 22% of exam
  • Ground Power Lines Hazards Access Site Picker

Operations

  • 28% of exam
  • Signals Setup Emergency Special Lifts Signal Picker

Technical Knowledge

  • 23% of exam
  • Systems Wire Rope Inspections Devices Aid Picker

Load Charts

  • 27% of exam
  • Chart Terms Deductions Radius Line Pull Chart Picker

Quick Facts

  • Exam MCO Core
  • Questions 95 core
  • Time 90 min
  • Calculator Core: no
  • Specialty 28 questions
  • Cert term 5 years
  • Window 12 months
  • Designations LAT TSS TLL

Ground Scan SI

  • Look below, surface, and boom.
  • Voids Slopes Excavations Quadrant

Site Picker SI

  • Ground unknown → Qualified evaluation
  • Void or tank → Avoid setup
  • Soft surface → Mats cribbing
  • Near excavation → Keep setback
  • Power line nearby → Plan clearance
  • Blind landing → Signal person

Ground SI

  • Firm Resists settlement
  • Drained No water weakening
  • Graded Supports level setup
  • Voids Hidden collapse risk
  • Loose fill Poor compaction
  • Slope Stability loss
  • Excavation Edge failure
  • Mats Spread outrigger load

Power Options SI

  • Ground, twenty, or Table A.
  • Deenergize 20 ft Table A

Site Hazards SI

  • Swing radius Barricade counterweight
  • Tail swing Crush zone
  • Underground Utilities or tanks
  • Overhead Lines or obstructions
  • Access road Support crane travel
  • Lift path Clear travel route
  • Landing area Ready before lift
  • Controlling entity Provides site information

Power Lines SI

  • <=50 kV 10 ft
  • >50-200 kV 15 ft
  • >200-350 kV 20 ft
  • >350-500 kV 25 ft
  • >500-750 kV 35 ft
  • >750-1000 kV 45 ft
  • Unknown voltage Use safe option
  • Tagline Nonconductive near lines

Stop Rule OP

  • Any stop signal stops everything.
  • Anyone Hazard Stop Verify

Signal Picker OP

  • Clear sight → Direct control
  • Obstructed view → Designated signaler
  • Radio used → Dedicated channel
  • Signal unclear → Stop first
  • New signal → Agree before lift
  • Hazard seen → Stop signal

Setup OP

  • Level Within manufacturer tolerance
  • Outriggers Per chart notes
  • Stabilizers Prevent tipping
  • Crawlers Extend as charted
  • Rubber Use on-rubber chart
  • Quadrant Capacity zone
  • Counterweight Match chart setup
  • Boom config Match chart notes

Signals OP

  • Hand Standard visual commands
  • Voice Dedicated channel
  • Audible Horn or whistle
  • Nonstandard Agree before lift
  • Blind lift Use signal person
  • Stop Anyone may give
  • Emergency stop Obey immediately
  • One signaler Avoid conflicting commands

Emergency OP

  • Power contact Stay in cab
  • Step potential Shuffle away
  • Control failure Stop operations
  • Overload Reduce load moment
  • Two-blocking Stop hoisting
  • Fire Secure then evacuate
  • Unattended Shutdown and secure
  • Authority Operator may stop

LMI vs LML TE

LMI

  • Displays condition
  • Warns operator

LML

  • Limits functions
  • Allows safer motion
  • Indicator warns; limiter intervenes

Aid Picker TE

  • Need angle → Boom angle indicator
  • Need length → Boom length indicator
  • Monitor load moment → LMI
  • Limit overload motion → LML
  • Prevent two-block → A2B
  • Check level → Level indicator

Systems TE

  • Boom angle Angle to horizontal
  • Boom length Extended boom measure
  • LMI Load moment display
  • LML Limits worsening functions
  • A2B Prevents two-blocking
  • Level indicator Setup aid
  • Hoist brake Controls suspended load
  • Boom stop Prevents over-angle

Aid vs Device TE

Aid

  • Helps operator
  • May have alternate procedure

Device

  • Required protection
  • Do not bypass
  • Know malfunction procedure

Wire Rope TE

  • Reeving Rope path
  • Parts line Supporting rope parts
  • Line pull Single-line limit
  • Running rope Moves over sheaves
  • Standing rope Fixed support rope
  • Birdcage Remove from service
  • Kink Remove from service
  • Broken wires Inspect replacement criteria

TSS vs TLL TE

TSS

  • Fixed operator station
  • Telescopic boom

TLL

  • Rotating operator station
  • Telescopic boom
  • Cab rotation separates them

Inspections TE

  • Shift Before operating
  • Monthly Documented inspection
  • Annual Comprehensive inspection
  • Modified Qualified person inspect
  • Repaired Inspect before use
  • Deficiency Evaluate safety hazard
  • Safety hazard Remove from service
  • Manufacturer Follow stricter procedures

Net Load CH

  • Gross minus gear equals net.
  • Gross Deductions Net Compare load

Gross vs Net CH

Gross

  • Read from chart
  • Before deductions

Net

  • Available to lift
  • After deductions
  • Net carries the load

Chart Picker CH

  • On outriggers → Outrigger chart
  • On rubber → Rubber chart
  • Crawler pick → Crawler chart
  • Traveling load → Pick-carry chart
  • Jib erected → Jib chart
  • Exact value absent → Less favorable

Chart Terms CH

  • Gross capacity Chart capacity
  • Net capacity After deductions
  • Load weight Object plus rigging
  • Radius Center to hook
  • Boom angle Chart reference
  • Range diagram Reach envelope
  • Work area Quadrant chart
  • Capacity limit Stability or structure

Radius vs Boom Angle CH

Radius

  • Center to hook
  • Capacity usually lower

Boom angle

  • Angle to horizontal
  • Infers working radius
  • Radius governs capacity

Deductions CH

  • Hook block Subtract from gross
  • Ball Subtract from gross
  • Rigging Subtract from gross
  • Jib stowed May require deduction
  • Jib erected Use correct chart
  • Aux sheave Check chart notes
  • Whip line Check chart notes
  • Load line Deduct if required

Stability vs Structural CH

Stability

  • Tipping limit
  • Ground and radius sensitive

Structural

  • Component strength limit
  • Do not exceed
  • Both limits matter

Chart Rules CH

  • Unlisted radius Use next larger
  • Unlisted boom Use next longer
  • Notes Govern the chart
  • Configuration Must match exactly
  • On rubber Separate capacity chart
  • Pick carry Use travel chart
  • Parts line Check enough capacity
  • Calculator Specialty only

Common Traps

Chart Capacity Trap

  • Gross chart value ≠ Net usable capacity

Radius Trap

  • Measured before load ≠ Deflects under load

Power-Line Trap

  • Assume deenergized ≠ Assume energized

Signal Trap

  • Random directions ≠ Designated signaler

Outrigger Trap

  • Partly extended guess ≠ Charted position only

Inspection Trap

  • Deficiency noted ≠ Hazard evaluated

Specialty Trap

  • Core only ≠ Core plus specialty

Last Minute

  • 1. Core: 95 questions, 90 minutes
  • 2. Core calculator is prohibited
  • 3. Site 22; Operations 28
  • 4. Technical 23; Charts 27
  • 5. Use exact crane configuration
  • 6. Net equals gross minus deductions
  • 7. Unlisted radius: next larger
  • 8. Unlisted boom: next longer
  • 9. Stop signal: anyone may give
  • 10. Power lines presumed energized
  • 11. Outriggers follow chart notes
  • 12. Certification window is 12 months

NCCCO Mobile Crane

  • Practice Questions 200 questions Study Guide 18 topics Cheat Sheet 96 facts Flashcards 50 cards Blogs 1 blog Free CE Podcast