Cheat sheet

NCCER Millwright Cheat Sheet

Practice this exam

Machinery Installation & Alignment

  • 20% of exam
  • Foundations & Installation Hand Tools & Fasteners Shaft Alignment Alignment Method Picker Rigging & Safety

Precision Measurement

  • 15% of exam
  • Precision Measuring Tools Trade Math & Blueprints Micrometer vs Dial Indicator Blueprint Reading

Bearings & Lubrication

  • 20% of exam
  • Bearing Types & Failure Lubrication Bearing & Vibration Diagnosis True vs False Brinelling

Pumps & Mechanical Seals

  • 20% of exam
  • Pumps Mechanical Seals & Sealing Pump Problem Picker Cavitation vs Gas Binding

Conveyors, Compressors & Turbines

  • 25% of exam
  • Belt, Chain & Gear Drives Compressors & Turbines Hydraulics & Pneumatics Drive System Picker

Quick Facts

  • Exam NCCER Millwright
  • Credential NCCER Registry
  • Questions 100 multiple-choice
  • Time 2 hours
  • Pass 70%
  • Level Journey-level
  • Curriculum 4 levels (2021 ed.)
  • Expires Never (Registry)

Alignment Sequence IN

  • Level, Soft Foot, Rough, Fine, Dowel
  • Level: baseplate flat Soft foot: shim first Rough: jackscrews close Fine: dial/laser final Dowel: lock position

Rim-and-Face vs Reverse-Indicator IN

Rim-and-Face

  • One shaft's rim + face
  • Needs a solid face
  • Axial float risk

Reverse-Indicator

  • Both shafts' OD only
  • No face reading
  • Avoids float error
  • Face-dependent vs face-free

Alignment Method Picker IN

  • No face reading wanted → Reverse-indicator ( Two brackets )
  • Face surface is reliable → Rim-and-face ( Axial float risk )
  • Fast rough check only → Straightedge + feeler ( Visual pass )
  • Tight final tolerance → Laser alignment ( Digital readout )
  • Multiple baseplate elevations → Optical level ( Room reference )
  • Machine runs hot → Cold target offset ( Thermal growth )

Hand Tools & Fasteners IN

  • Ball peen hammer Strikes chisels, sets rivets
  • Box-end wrench Grips all six bolt points
  • Tap and die Cut new internal/external threads
  • SAE Grade 5 Three radial lines on head
  • SAE Grade 8 Six radial lines on head
  • Right-hand thread Tightens clockwise
  • Wedge anchor Steel clip expands in concrete
  • Sleeve anchor Sleeve expands as bolt tightens
  • Epoxy anchor Adhesive bonds bolt to concrete

Foundations & Installation IN

  • Soft foot Frame twists once bolted down
  • Star bolt pattern Even, progressive clamping force
  • Jackscrews Fine-tune position before bolt-down
  • Dowel pins Lock final aligned position
  • Grouting Fills the baseplate void
  • Baseplate Fixed machine mounting surface
  • Thermal growth Casing expands as it heats
  • Woodruff key Self-aligns on tapered shafts
  • Gib-head key Angled head drives out easily

Shaft Alignment IN

  • Offset misalignment Parallel centerlines, shifted sideways
  • Angular misalignment Centerlines meet at an angle
  • Reverse-indicator method No face reading needed
  • Rim-and-face method Reads rim plus coupling face
  • Bar sag Bracket deflection error to subtract
  • Cold alignment target Preset offset before startup
  • Laser alignment Digital shaft offset readout
  • 12-3-6-9 readings Separate vertical from horizontal
  • Shim Corrects vertical position only

Rigging & Safety IN

  • Personnel-hoist rigging Needs a 5:1 safety factor
  • Suspension scaffold rope Needs a 6:1 safety factor
  • Sling angle Shallower angle raises leg tension
  • Center of gravity Must hang directly under hook
  • LOTO Physically isolates every energy source
  • Hard hat Type I Top-impact protection only
  • Hard hat Type II Top plus lateral protection
  • Class G hard hat Protects up to 2,200 volts
  • Class E hard hat Protects up to 20,000 volts
  • Bench grinder gap Work rest within 1/8 inch

Micrometer vs Dial Indicator ME

Micrometer

  • Absolute size
  • Thousandths of an inch
  • Static dimension

Dial Indicator

  • Relative movement
  • Runout/alignment use
  • Zero-reference change
  • Size vs movement

Precision Measuring Tools ME

  • Micrometer Reads size to 0.001 in
  • Vernier scale Adds 0.0001 in resolution
  • Dial indicator Reads relative movement, runout
  • Feeler gauge Checks a static gap
  • Bore gauge Measures internal bore diameter
  • Optical level Sets a room reference plane
  • Straightedge Checks baseplate flatness
  • Torque wrench Verifies bolt clamping force
  • Stroboscope Checks rotating shaft speed

Trade Math & Blueprints ME

  • Taper per foot Diameter change over shaft length
  • Sheave ratio Speed is inverse of diameter
  • Gear reducer ratio Speed down, torque up
  • Hidden line Short dashes, edge not visible
  • Centerline Marks an axis of symmetry
  • Detail drawing One part, full dimensions
  • Assembly drawing Shows multiple parts together
  • P&ID Piping and instrumentation diagram

Vibration Frequency BE

  • 1X Means Unbalance, 2X Means Misalignment
  • 1X: rotor weight 2X: coupling misalignment Bearing tone: race defect Broadband: looseness

True vs False Brinelling BE

True Brinelling

  • Static overload or impact
  • Permanent race dent
  • Single event cause

False Brinelling

  • Vibration while stationary
  • Fretting wear pattern
  • No overload event
  • Impact vs fretting

Bearing & Vibration Diagnosis BE

  • Static overload dent → True brinelling ( Impact damage )
  • Marks with no overload → False brinelling ( Shipping fretting )
  • Flaking or pitted race → Spalling ( Fatigue failure )
  • Peak at 1X RPM → Suspect unbalance ( Rotor weight )
  • Peak at 2X RPM → Suspect misalignment ( Coupling stress )
  • Install without impact → Induction heater ( Below 250°F )
  • Over-filled grease housing → Drop to half full ( Prevent overheat )

Bearing Types & Failure BE

  • Anti-friction bearing Uses rolling balls or rollers
  • Plain/sleeve bearing Relies on an oil film
  • Tapered roller bearing Handles radial plus thrust load
  • Thrust bearing Absorbs axial load only
  • L10 life 90% survive that rating
  • True brinelling Static overload dents the race
  • False brinelling Fretting wear while stationary
  • Spalling Fatigue flaking of the race
  • Heat limit Stay below about 250°F

L10 Bearing Life BE

  • L10 Equals 90 Percent Still Surviving
  • 10% may fail early Statistical, not guaranteed Higher load shortens L10

Grease vs Oil BE

Grease

  • Stays in place
  • Low maintenance
  • Moderate speed use

Oil

  • Better heat removal
  • Can filter and circulate
  • High-speed, high-temp use
  • Simplicity vs cooling

Lubrication BE

  • NLGI Grade 2 Most common grease consistency
  • ISO VG 68 Oil viscosity centered at 68 cSt
  • Grease Low maintenance, stays in place
  • Oil Better cooling, high-speed use
  • Fill level One-third to one-half full
  • Oil analysis Tracks wear-metal trends
  • Thermography Finds abnormal heat patterns

Grease Fill Rule BE

  • Fill One-Third To One-Half, Never Full
  • Full housing overheats Churn needs air space Over-grease is a real risk

NPSH Rule PU

  • Keep NPSH Available Above NPSH Required
  • NPSHa: system side NPSHr: pump spec Margin avoids cavitation

Centrifugal vs Positive-Displacement Pump PU

Centrifugal

  • Flow varies with pressure
  • Throttle changes output
  • No relief valve needed

Positive Displacement

  • Fixed volume per revolution
  • Needs a relief valve
  • Pressure builds if blocked
  • Variable vs fixed flow

Pump Problem Picker PU

  • Pitted, noisy impeller → Check NPSHa margin ( Cavitation )
  • Lost prime, no pitting → Check for gas binding ( Air ingress )
  • Discharge fully closed → Open valve or relief ( Dead-head heat )
  • Seal leaking, scored faces → Check the flush plan ( API plan )
  • Flow and head both drop → Check wear rings ( Internal recirculation )

Pumps PU

  • Centrifugal pump Flow varies with pressure
  • Positive-displacement pump Fixed volume per revolution
  • NPSH required Pump's own suction spec
  • NPSH available System's actual suction margin
  • Cavitation Vapor bubbles collapse, pit impeller
  • Gas binding Air displaces liquid, loses prime
  • Dead-heading Closed discharge overheats fluid
  • Wear ring clearance Controls internal fluid recirculation

Cavitation vs Gas Binding PU

Cavitation

  • Local pressure drops
  • Vapor bubbles collapse
  • Pits the impeller

Gas Binding

  • Air or gas enters suction
  • Displaces liquid at eye
  • Loses prime, no pitting
  • Vapor collapse vs air displacement

Mechanical Seals & Sealing PU

  • Mechanical seal Two lapped faces, near-zero leak
  • Packing gland Controlled drip cools packing
  • Flush plan Cools and cleans seal faces
  • O-ring Static or dynamic elastomer seal
  • Spiral wound gasket High-temperature, high-pressure joints
  • Cork composite gasket Lower pressure, lower cost joints

Mechanical Seal vs Packing Gland PU

Mechanical Seal

  • Two lapped faces
  • Near-zero leakage
  • Higher cost, precision

Packing Gland

  • Compressed packing rings
  • Controlled drip cools it
  • Simpler, more upkeep
  • Sealed vs designed-to-leak

V-Belt vs Timing Belt RO

V-Belt

  • Wedges into a groove
  • Friction-based grip
  • Some slip possible

Timing Belt

  • Toothed engagement
  • Positive, slip-free drive
  • Exact synchronization
  • Friction vs positive drive

Drive System Picker RO

  • Need slip-free timing → Timing belt ( Toothed drive )
  • Need max friction torque → V-belt ( Wedge grip )
  • Light duty, low torque → Flat belt ( Surface friction )
  • Need positive chain drive → Roller chain ( Check elongation )
  • Increase torque, cut speed → Gear reducer ( Same power )
  • Incline conveyor loses power → Backstop device ( Blocks runback )

Belt, Chain & Gear Drives RO

  • V-belt Wedges into a grooved pulley
  • Flat belt Plain surface friction only
  • Timing belt Toothed, positive, slip-free drive
  • Over-tensioned belt Overloads bearings and shafts
  • Under-tensioned belt Slips, glazes, and overheats
  • Chain elongation Pin and bushing wear adds up
  • Gear reducer Trades speed for more torque
  • Backstop Blocks reverse runback on inclines
  • Belt tracking Tension, crown, or buildup issue

Compressors & Turbines RO

  • Reciprocating compressor Piston compresses gas in pulses
  • Rotary screw compressor Continuous meshing-rotor compression
  • Intercooling Removes heat between compression stages
  • Governor Holds turbine speed under load
  • Radial clearance Tight blade-to-casing gap
  • Axial thrust Rotor pushed along its axis
  • Thrust bearing Absorbs that axial force

Hydraulics & Pneumatics RO

  • Pascal's law Pressure transmits equally in fluid
  • Force = pressure x area Sizes cylinder output force
  • Hydraulic reservoir Stores, cools, settles the fluid
  • FRL unit Filters, regulates, lubricates air
  • Double-acting cylinder Force in both directions
  • Single-acting cylinder Force one way, spring returns

Common Traps

Micrometer vs dial indicator

  • Micrometer reads part size ≠ Dial indicator reads movement

True vs false brinelling

  • True = impact damage ≠ False = fretting wear

Cavitation vs gas binding

  • Cavitation collapses vapor bubbles ≠ Gas binding traps entrained air

NPSHa vs NPSHr

  • NPSHa = system's margin ≠ NPSHr = pump's spec

5:1 vs 6:1 rigging factor

  • Personnel-hoist rigging needs 5:1 ≠ Suspension scaffold rope needs 6:1

1X vs 2X vibration

  • 1X peak signals unbalance ≠ 2X peak signals misalignment

Hard hat Class G vs E

  • Class G caps at 2,200V ≠ Class E caps at 20,000V

Last Minute

  • 1. Exam: 100 questions, 2 hours, 70%
  • 2. Weights: 20-15-20-20-25 by domain
  • 3. Micrometer = size; indicator = movement
  • 4. Reverse-indicator needs no face reading
  • 5. Shims correct vertical position only
  • 6. 1X = unbalance; 2X = misalignment
  • 7. Heat bearings below 250°F only
  • 8. L10 = 90% survive rating
  • 9. Grease fills one-third to half
  • 10. Keep NPSHa above NPSHr always
  • 11. Cavitation = vapor; gas binding = air
  • 12. Scaffold rope factor is 6:1
  • 13. Personnel-hoist rigging factor is 5:1
  • 14. LOTO isolates energy, not just off

NCCER Millwright

  • Practice Questions 130 questions Study Guide 35 topics Cheat Sheet 106 facts Flashcards 50 cards Shorts 2 short s Videos 1 video Blogs 1 blog Free CE Podcast