Cheat sheet

NFPA 1002 Driver/Operator Apparatus Cheat Sheet

Practice this exam

Standards + Certification

  • Not published of exam
  • Standards Map 2026 Certification Path Chapter 11 JPR Map Chapter 12 JPR Map

Inspection + Maintenance

  • Not published of exam
  • Daily Check Items Annual Pump Service Test Pumper Minimum Specs Air Brake Checks

Driving + Positioning

  • Not published of exam
  • Fixed Driving Exercises Driving Physics Due Regard + Response Scene Positioning

Pump Theory + Panel

  • Not published of exam
  • Centrifugal Pump Theory Panel Controls + Gauges Pressure Control Devices Cavitation vs Water Hammer

Hydraulics + Water Supply

  • Not published of exam
  • Core Formulas Friction Loss Coefficients Nozzle Pressures + Losses Hydrant + Percentage Method Drafting + Lift Relay + Water Shuttle Foam + Proportioning Standpipe + Sprinkler Support

Quick Facts

  • Standard NFPA 1010 Chapters 11-12
  • Edition 2024 edition
  • Replaced NFPA 1002, now consolidated
  • Required chapters Chapters 4, 11, and 12
  • Accreditation Pro Board or IFSAC
  • Who certifies State or regional entity
  • Prerequisite None in NFPA 1010
  • Questions Set by certifying entity
  • Pass mark Entity set; 70% common
  • Also required Practical skills evaluation
  • Stay qualified Annual competency demonstration
  • Pro Board compliance NFPA 1010 since June 30, 2026

Standards Map 2026 ST

  • NFPA 1010 Firefighter pro qualifications 2024 2024 ed.
  • Chapter 11 Driver/operator general requirements
  • Chapter 12 Pumper apparatus JPRs
  • Chapter 13 Aerial device apparatus
  • Chapter 14 Tiller apparatus
  • Chapter 15 Wildland suppression apparatus
  • Chapter 16 Aircraft rescue firefighting apparatus
  • Chapter 17 Mobile water supply apparatus
  • Replaced NFPA 1002 Also 1001, 1003, 1005
  • NFPA 1900 New apparatus design standard
  • NFPA 1910 In-service inspection and testing
  • NFPA 291 Hydrant flow testing, marking
  • NFPA 1091 Traffic incident management
  • NFPA 1550 Responder health and safety Replaced 1500

Certification Path ST

  • Required chapters Chapters 4, 11, and 12 4.4.7.2
  • Pro Board tests Chapter 11 plus 12
  • Prerequisite None listed by NFPA
  • Driver license All vehicles you operate
  • Annual proof Demonstrate competency every year
  • Test vehicle Similar weight, wheelbase, function
  • AHJ sets Age, medical, background rules
  • Written plus practical Both required to certify
  • Domain weights Not published by NFPA
  • Item count Entity set, commonly 100
  • Pass mark Entity set, 70% common
  • Compliance deadline June 30, 2026 Pro Board
  • State adoption dates Vary by state, 2026-2027

Chapter 11 JPR Map ST

  • 11.2.1 Verify apparatus operational status
  • 11.2.2 Document inspection and maintenance
  • 11.3.1 + 11.3.6 Road driving operations test
  • 11.3.2 Alley dock exercise
  • 11.3.3 Serpentine exercise
  • 11.3.4 Confined space turnaround
  • 11.3.5 Diminishing clearance exercise
  • 11.3.7 Operate fixed systems and equipment
  • Chapter 11 applies Every driver/operator apparatus type

Chapter 12 JPR Map ST

  • 12.2.1 + 12.2.2 Response and communications JPRs
  • 12.3.1 Pumper-specific inspection additions
  • 12.4.1 Restraints and defensive driving
  • 12.4.2 Establish protected work areas
  • 12.4.3 Connect pumper to water supply
  • 12.4.4 Produce hand and master streams
  • 12.4.5 Pump a supply line
  • 12.4.6 Pump a foam stream
  • 12.4.7 Supply sprinklers and standpipes

Pump Test Runs MA

  • One fifty, two hundred, two fifty
  • 100% capacity, 150 psi 70% capacity, 200 psi 50% capacity, 250 psi Twenty, ten, ten minutes

NFPA 1900 vs NFPA 1910 MA

NFPA 1900

  • How apparatus is built
  • Replaced NFPA 1901
  • Design and construction

NFPA 1910

  • Inspection, testing, retirement
  • Replaced NFPA 1911
  • Annual pump service test
  • New versus in-service

Out-of-Service Picker MA

  • Air leak in brakes → Out of service ( Safety critical )
  • Warning lights inoperative → Out of service ( Cannot respond safely )
  • Fuel below three-quarters → Refuel now ( Then document )
  • Fluid level slightly low → Top off, record ( Return to service )
  • Pump fails vacuum test → Repair before pumping ( Cannot hold prime )
  • Any deficiency found → Report and document ( JPR 11.2.2 )

Daily Check Items MA

  • Tires Tread depth and inflation
  • Batteries Clean, corrosion free, secured
  • Engine oil Level within manufacturer specifications
  • Coolant Level within manufacturer specifications
  • Fuel Keep above three-quarters tank
  • Belts Tight, no excessive wear Engine off
  • Electrical Warning lights and sirens
  • Brakes Check air and fluid leaks
  • Steering Linkage wear, fluid level
  • Transmission Fluid level within specifications
  • Pump systems Engage and check pump 12.3.1
  • Water tank Agent levels topped off
  • Foam system Concentrate level, if equipped
  • Deficiencies Report and document immediately

Pumper vs Mobile Water Supply MA

Pumper

  • 750 gpm pump minimum
  • 300 gallon tank minimum
  • 40 cubic feet compartments

Mobile water supply

  • 1,000 gallon tank minimum
  • Pump not required
  • 6 cubic feet hose
  • Pump versus tank

Annual Pump Service Test MA

  • 100% capacity 150 psi, 20 minutes
  • 70% capacity 200 psi, 10 minutes
  • 50% capacity 250 psi, 10 minutes
  • Test source Draft, lift under 10 ft
  • Vacuum test Pull at least 22 in. Hg
  • Vacuum drop limit 10 in. Hg per 5 minutes
  • Primer during test Off once timing starts
  • Priming time 30 seconds up to 1,250 gpm
  • Larger pumps 45 seconds at 1,500 gpm
  • Auxiliary intake Adds 15 seconds allowance
  • Transfer valve Volume position for priming
  • Governing standard NFPA 1910, formerly 1911

Pumper Minimum Specs MA

  • Fire pump 750 gpm minimum
  • Water tank 300 gallons minimum
  • Compartments 40 cubic feet minimum
  • Hose bed 30 cubic feet, 2½-inch
  • Preconnects Two areas, 3.5 cubic feet
  • Rating point Draft at 10 ft lift
  • Rating pressures 150, 200, and 250 psi
  • Mobile water supply 1,000 gallon tank minimum
  • Design standard NFPA 1900, formerly 1901

Air Brake Checks MA

  • Governor cut-out Around 120 to 140 psi
  • Governor cut-in Around 85 to 100 psi
  • Static leak test Engine off, one minute
  • Applied leak test Hold brake, time one minute
  • Low-air warning Alarm at 55 psi minimum
  • Spring brakes Pop out 20-45 psi
  • Brake lag Air travel delay before braking
  • Chock wheels Before any brake testing

Four Driving Exercises DR

  • Alley, Serpentine, Confined, Diminishing
  • Alley dock: 12 ft space Serpentine: back then forward Confined: 180 degree turn Diminishing: narrowing clearance

Fixed Driving Exercises DR

  • Alley dock Back into 12 ft space 11.3.2
  • Alley dock turns 90 degrees, right and left
  • Serpentine Back then drive through markers 11.3.3
  • Confined space turnaround Turn vehicle 180 degrees 11.3.4
  • Diminishing clearance Horizontal and vertical restrictions 11.3.5
  • Course markers Striking one fails skill
  • Backing rule Always use a spotter
  • Test vehicle Similar weight and wheelbase

Driving Physics DR

  • Total stopping distance Reaction plus lag plus braking
  • Weight transfer Braking shifts weight forward
  • Centrifugal force Grows with speed squared
  • Liquid surge Partial tank shoves apparatus
  • Rollover risk High center of gravity
  • ABS braking Firm steady pressure, steer
  • Never pump ABS Pumping defeats the system
  • Hydroplaning Slow down, avoid hard steering
  • Following distance Longer than any passenger vehicle

Due Regard + Response DR

  • Due regard Reasonable care for others
  • Exemptions apply Only with lights and siren
  • Red light Come to complete stop
  • Stop sign Complete stop before proceeding
  • Negative right-of-way Intersection where you yield
  • Seat belts Fastened before wheels move 12.4.1
  • Riding position Seated and belted only
  • Speed Never exceeds safe control
  • Backing Spotter or walk-around first

Scene Positioning DR

  • Front of building Save it for aerial
  • Uphill and upwind Standard hazardous materials positioning
  • Supply position Pumper takes the hydrant 12.4.3
  • Attack position Short stretch to entry
  • Protected work area Set devices before working 12.4.2
  • Traffic incidents Block with the apparatus
  • Collapse zone One and a half heights
  • Overhead hazards Avoid wires and limbs

Cavitation Signs PU

  • Speed up, pressure down, gravel sound
  • Engine rpm climbs Discharge pressure drops Rattling inside the pump Fix: throttle back

Volume vs Pressure PU

Volume, parallel

  • Both impellers feed discharge
  • Full rated capacity
  • Use above 50% capacity

Pressure, series

  • First impeller feeds second
  • Half rated capacity
  • Pressure roughly doubles
  • Flow versus pressure

Pump Problem Picker PU

  • Rpm up, pressure down → Cavitation ( Throttle back )
  • Gravel sound in pump → Cavitation ( Reduce the flow )
  • Primer runs, no vacuum → Find air leak ( Check caps, gaskets )
  • Pressure spikes on shutdown → Water hammer ( Close valves slowly )
  • Pump overheats at idle → Open pump cooler ( Little water flowing )
  • Pressure creeps up → Set relief valve ( Or use governor )
  • Need pressure, low flow → Pressure position ( Series staging )

Centrifugal Pump Theory PU

  • Centrifugal pump Nonpositive displacement, cannot self-prime
  • Impeller Adds velocity to water
  • Volute Converts velocity into pressure
  • Primer Positive displacement, removes air
  • Single stage One impeller, most pumpers
  • Two stage Two impellers, transfer valve
  • Volume position Parallel, full rated capacity
  • Pressure position Series, half rated capacity
  • Change to volume Flow above 50% capacity
  • Rated capacity 100% at 150 psi
  • Net pump discharge pressure Discharge minus intake pressure
  • Draft net pressure Discharge plus lift losses

PSI Mode vs RPM Mode PU

PSI mode

  • Holds set discharge pressure
  • Changes engine speed automatically
  • Preferred for attack lines

RPM mode

  • Holds set engine speed
  • Pressure moves with flow
  • Acts like manual throttle
  • Pressure versus throttle

Transfer Valve Picker PU

  • Flow above 50% capacity → Volume position ( Parallel staging )
  • Flow at or below half → Pressure position ( Series staging )
  • Long lines, high pressure → Pressure position ( Pressure roughly doubles )
  • Supplying large master stream → Volume position ( Full rated capacity )
  • Priming or service test → Volume position ( Standard test setup )
  • Single-stage pump → No transfer valve ( Nothing to change )

Panel Controls + Gauges PU

  • Master intake gauge Compound, also reads vacuum
  • Master discharge gauge Pressure leaving the pump
  • Tachometer Engine speed in rpm
  • Pump shift Engages pump from transmission
  • OK to pump Green light before throttling
  • Tank to pump Feeds pump from tank
  • Tank fill Refills tank from pump
  • Primer control Creates vacuum for draft
  • Transfer valve Volume or pressure selection
  • Discharge gates Open and close slowly

Relief Valve vs Governor PU

Relief valve

  • Mechanical, dumps excess water
  • Pressure bypasses back
  • Engine speed unchanged

Governor

  • Electronic, changes engine speed
  • No water dumped
  • Two selectable modes
  • Dump versus throttle

Pressure Control Devices PU

  • Relief valve Dumps excess discharge pressure
  • Intake relief Protects pump from surge
  • Governor PSI mode Holds set discharge pressure
  • Governor RPM mode Holds set engine speed
  • Water hammer Surge from sudden closure
  • Cavitation Discharging more than receiving
  • Cavitation signs Rpm rises, pressure falls
  • Cavitation sound Gravel rattling in pump
  • Cavitation fix Throttle back, add supply
  • Pump cooler Cools recirculating pump water

Cavitation vs Water Hammer PU

Cavitation

  • Pump starved of water
  • Rpm up, pressure down
  • Gravel rattling sound

Water hammer

  • Moving water stopped suddenly
  • Pressure surge and shock
  • Close valves slowly
  • Starved versus stopped

Pump Discharge Pressure HY

  • Nozzle, Friction, Appliance, Elevation
  • NP: nozzle pressure FL: hose friction loss APPL: appliances and standpipe ELEV: up adds, down subtracts

Static vs Residual HY

Static

  • No water moving
  • Stored system pressure
  • Read before opening

Residual

  • Water is flowing
  • Pressure left in system
  • Never below 20 psi
  • Stopped versus flowing

Water Source Picker HY

  • Hydrant close, good pressure → Direct hydrant supply ( Simplest option )
  • Hydrant far from scene → Relay pumping ( Boost the pressure )
  • No hydrant, static source → Draft ( Hard suction needed )
  • No hydrant, no static → Water shuttle ( Tankers and portable tank )
  • Lift above 25 feet → Move closer ( Lift too high )
  • Intake falls under 20 psi → Add a pumper ( Cavitation risk )

Core Formulas HY

  • Pump discharge pressure Nozzle, friction, appliance, elevation
  • Friction loss C times Q² times L
  • Q means Gpm divided by 100
  • L means Length in hundreds of feet
  • Smooth bore flow 29.7 times d² times √NP
  • Elevation exact 0.434 psi per foot
  • Elevation fireground 5 psi per floor
  • Percent drop Static minus residual, over static
  • Head conversion 1 psi lifts 2.304 ft
  • Flow rule Double flow, quadruple friction loss

Percentage Method HY

  • Ten three, fifteen two, twenty-five one
  • 0-10% drop: three lines 11-15% drop: two lines 16-25% drop: one line Over 25%: less than one

Draft vs Hydrant Supply HY

Draft

  • Atmospheric pressure pushes water
  • Primer required first
  • Lift limits the flow

Hydrant

  • System pressure feeds pump
  • No primer needed
  • Watch residual pressure
  • Vacuum versus pressure

Nozzle Pressure Picker HY

  • Smooth bore handline → 50 psi ( Solid stream )
  • Smooth bore master stream → 80 psi ( Deck gun tip )
  • Standard fog nozzle → 100 psi ( Combination nozzle )
  • Low-pressure fog nozzle → 75 psi ( Reduced nozzle reaction )
  • Standpipe operation → Smooth bore ( Pressure device uncertainty )
  • Flow over 350 gpm → Add appliance loss ( 10 psi )

Friction Loss Coefficients HY

  • 1½-inch C equals 24
  • 1¾-inch C equals 15.5
  • 2-inch C equals 8
  • 2½-inch C equals 2 Baseline
  • 3-inch C equals 0.8 2½-inch couplings
  • 3½-inch C equals 0.34
  • 4-inch C equals 0.2
  • 4½-inch C equals 0.1
  • 5-inch C equals 0.08
  • 6-inch C equals 0.05
  • 1-inch booster C equals 150
  • Upsizing hose Cuts friction loss sharply

Nozzle Pressures HY

  • Fifty solid, eighty master, hundred fog
  • 50 psi smooth bore handline 80 psi smooth bore master 100 psi standard fog 75 psi low-pressure fog

Class A vs Class B Foam HY

Class A

  • Ordinary combustibles and wildland
  • 0.1% to 1.0%
  • Acts as wetting agent

Class B

  • Flammable and combustible liquids
  • 1%, 3%, or 6%
  • Seals vapor with blanket
  • Wetting versus sealing

Foam Picker HY

  • Ordinary combustibles or wildland → Class A foam ( 0.1% to 1.0% )
  • Gasoline or diesel spill → Class B at 3% ( Hydrocarbon fuel )
  • Ethanol or alcohol fuel → AR-AFFF at 6% ( Polar solvent )
  • Burning hydrocarbon spill → 0.10 gpm per ft² ( Fifteen minute run time )
  • Burning polar solvent → 0.20 gpm per ft² ( Double the rate )
  • Weak foam from eductor → Check 65 percent rule ( Back pressure high )

Nozzle Pressures + Losses HY

  • Smooth bore handline 50 psi nozzle pressure
  • Smooth bore master 80 psi nozzle pressure
  • Fog nozzle 100 psi nozzle pressure
  • Low-pressure fog 75 psi nozzle pressure
  • Appliance under 350 gpm Loss small enough to ignore
  • Appliance 350 gpm up Add 10 psi
  • Standpipe system Add 25 psi
  • Master stream device Add 25 psi
  • Handline versus master Split at 350 gpm

Lift Numbers HY

  • Thirty-four theoretical, ten ideal, fifteen dependable
  • 33.9 ft theoretical maximum 10 ft ideal lift 14.7 ft dependable lift 14.7 psi atmospheric

Hydrant + Percentage Method HY

  • Static pressure Stored pressure, nothing flowing
  • Residual pressure Pressure left while flowing
  • Flow pressure Measured with pitot gauge
  • Drop 0-10% Three more equal lines
  • Drop 11-15% Two more equal lines
  • Drop 16-25% One more equal line
  • Drop over 25% Less than one line
  • Residual floor Never below 20 psi
  • Class AA hydrant Light blue, 1,500 gpm up NFPA 291
  • Class A hydrant Green, 1,000 to 1,499 NFPA 291
  • Class B hydrant Orange, 500 to 999 NFPA 291
  • Class C hydrant Red, under 500 gpm NFPA 291
  • Dead-end main Collapses quickly under flow

Drafting + Lift HY

  • Atmospheric pressure 14.7 psi at sea level
  • Theoretical lift 33.9 ft at sea level
  • Ideal lift About 10 feet
  • Dependable lift 14.7 ft, most texts
  • Maximum lift About 22 to 25 feet
  • Measure lift Water surface to intake
  • Strainer depth At least 2 ft submerged
  • Strainer clearance 2 ft off the bottom
  • Air leaks Prevent prime from holding
  • Whirlpool Means strainer sits too shallow
  • Hard suction Rigid hose resists vacuum

Relay + Water Shuttle HY

  • Relay minimum 20 psi residual intake 12.4.5
  • Relay target 20 to 30 psi
  • Source pumper Largest capacity at source
  • Constant pressure relay About 175 psi discharge
  • Dump line Relieves excess intake pressure
  • Shuttle flow limits Fill rate, dump rate, travel
  • Not the limit Tanker tank size alone
  • Portable tank Dump site holding basin

Foam + Proportioning HY

  • Class A concentrate 0.1% to 1.0%
  • Class B concentrate 1%, 3%, or 6%
  • AR-AFFF 3% hydrocarbon, 6% polar
  • Eductor principle Venturi creates low pressure 12.4.6
  • Eductor inlet Rated at 200 psi
  • 65 percent rule Downstream under 65% of inlet
  • Eductor hose limit 150 ft to nozzle
  • Hydrocarbon rate 0.10 gpm per square foot
  • Polar solvent rate 0.20 gpm per square foot
  • Run time At least 15 minutes
  • Flow match Eductor and nozzle ratings

Standpipe + Sprinkler Support HY

  • Connection point Fire department connection, FDC 12.4.7
  • Standpipe allowance Add 25 psi
  • Elevation per floor Add 5 psi
  • Ground floor Adds no elevation pressure
  • Standpipe nozzle choice Smooth bore preferred
  • Sprinkler FDC 150 psi common default AHJ sets
  • Never shut down Sprinklers controlling the fire
  • Two FDC inlets Supply both when possible
  • Second supply line Add if flow increases

Common Traps

NFPA 1002 vs NFPA 1010

  • NFPA 1002 was consolidated ≠ Content now NFPA 1010 Chapters 11-12

NFPA 1900 vs NFPA 1910

  • 1900 builds new apparatus ≠ 1910 tests in-service apparatus

Elevation exact vs fireground

  • 0.434 psi per foot exact ≠ 5 psi per floor shortcut

Volume does not add pressure

  • Volume gives full capacity ≠ Pressure position doubles pressure

Cavitation is not water hammer

  • Cavitation starves the pump ≠ Water hammer stops moving water

Discharge relief vs intake relief

  • Discharge relief controls outgoing ≠ Intake relief protects incoming

Firefighter I is not required

  • NFPA 1010 lists no prerequisite ≠ Many AHJs require it anyway

Low-air warning vs spring brakes

  • Warning alarms near 55 psi ≠ Spring brakes pop 20-45 psi

Priming thresholds are not equal

  • 30 seconds to 1,250 gpm ≠ 45 seconds at 1,500 gpm

Percentage method counts added lines

  • Answer is additional lines ≠ Not the total flow available

Pump rating is not tank flow

  • Rating set at 10 ft draft ≠ Tank-to-pump flow is lower

Hydrant residual has a floor

  • Never below 20 psi residual ≠ Low residual can collapse mains

Last Minute

  • 1. Pumper operator = Chapters 11 and 12
  • 2. NFPA writes it; state entity certifies
  • 3. PDP = nozzle + friction + appliance + elevation
  • 4. Friction loss uses C Q² L
  • 5. Double the flow, quadruple the loss
  • 6. Smooth bore 50; fog 100 psi
  • 7. Elevation exact is 0.434 psi/ft
  • 8. Appliance loss starts at 350 gpm
  • 9. Never let residual drop below 20
  • 10. Volume above half; pressure below half
  • 11. Cavitation: rpm up, pressure down
  • 12. Theoretical lift 33.9 ft; ideal 10
  • 13. Pump test: 150, 200, 250 psi
  • 14. Vacuum 22 in. Hg minimum
  • 15. Alley dock space is 12 ft
  • 16. Class A foam: 0.1% to 1.0%
  • 17. Eductor: 65 percent downstream limit
  • 18. Green hydrant = 1,000 to 1,499 gpm
  • 19. Pumper minimum: 750 gpm, 300 gallons
  • 20. Annual competency demonstration is required

NFPA 1002 Driver/Operator — Apparatus

  • Practice Questions 125 questions Study Guide 18 topics Cheat Sheet 237 facts Flashcards 50 cards 1 Job Wiki Free CE Podcast