Cheat sheet
NICET Water-Based Systems Layout Cheat Sheet
Component and Code Map
- Not published of exam
- Exam Components Reference Map Level III Edition Check
Documents and Surveys
- Not published of exam
- Plan Set Field Survey Flow Test Existing Conditions
Hazards and Criteria
- Not published of exam
- Hazard Classification Storage Design Criteria AHJ
System Layout
- Not published of exam
- System Types Sprinkler Layout Obstructions Supports
Hydraulics
- Not published of exam
- Hydraulic Chain K-Factor Friction Loss Demand
Water Supply and Equipment
- Not published of exam
- Water Supply Fire Pump Tank Standpipe
Submittals and Coordination
- Not published of exam
- Submittal RFI Coordination Change Order
Quick Facts
- Credential Four certification levels
- Exams Five separate components
- Level III General plus Hydraulics exams
- Pass 500 scaled; not raw percent
- Remote Level I only
- Retake 30 days; max three/12 months
- Recertify Every three years through CPD
- Reference edition NFPA 13 (2022) all components
Five Exams CO
- I, II, III-General, III-Hydraulics, IV
- I: 105 questions, 150 minutes II: 120 questions, 225 minutes III-G: 70 questions, 175 minutes III-H: 60 questions, 240 minutes IV: 80 questions, 240 minutes
Component vs Program CO
One component
- One level or III part
- Own outline and references
WBSL program
- Four certification levels
- Five separate exam components
- Choose component before studying weights
Reference Picker CO
- Design sprinkler installation → NFPA 13 ( 2022 in every component )
- Level I dwelling scope → Check NFPA 13D ( 2022 reference )
- Level I residential scope → Check NFPA 13R ( 2022 reference )
- Standpipe design applies → NFPA 14 ( 2019; check component )
- Pump layout applies → NFPA 20 ( 2022; check component )
- Tank layout on III General → NFPA 22 ( 2018 reference )
- Flow-test method applies → NFPA 291 ( 2022; check component )
- Inspection topic on IV → NFPA 25 ( 2020 reference )
Exam Components CO
- Level I 105 questions; 150 minutes
- Level II 120 questions; 225 minutes
- III General 70 questions; 175 minutes
- III Hydraulics 60 questions; 240 minutes
- Level IV 80 questions; 240 minutes
- III-H break 15 minutes outside test time
- IV break 15 minutes outside test time
- III-H return No first-section access after break
Reference Map CO
- NFPA 13 (2022) All five WBSL components
- NFPA 13D (2022) Level I reference
- NFPA 13R (2022) Level I reference
- NFPA 14 (2019) II, III-G, III-H, IV
- NFPA 20 (2022) II, III-G, III-H, IV
- NFPA 22 (2018) III General reference
- NFPA 25 (2020) Level IV reference
- NFPA 291 (2022) I, II, III Hydraulics
- Brock Hydraulics, 3rd III Hydraulics reference
Flow Test Trio DO
- Static, residual, flowing: record together
- Static: no flow Residual: under flow Flow: measured discharge
Static vs Residual DO
Static
- No flow
- Baseline pressure
Residual
- During measured flow
- Pressure under demand
- Record whether flow is occurring
Plan Set DO
- Architectural plan Use, rooms, dimensions
- Reflected ceiling Ceiling features and head coordination
- Structural plan Beams, joists, support constraints
- Mechanical plan Ducts and spatial conflicts
- Specifications Project-specific material and performance
- Existing drawings Verify against site conditions
- Revision cloud Identify changed drawing area
Field Survey DO
- Field dimensions Verify actual clearances
- Existing riser Confirm system connection
- Pipe condition Check material and obstructions
- Backflow assembly Include pressure loss
- Static pressure Pressure without flow
- Residual pressure Pressure during flow
- Flow-test date Check supply-data currency
Occupancy vs Commodity HA
Occupancy hazard
- Building use and fuel
- Nonstorage criteria
Storage commodity
- Product plus packaging
- Storage-specific criteria
- Storage requires its own analysis
Hazard Classification HA
- Light Hazard Low combustibility and heat release
- Ordinary Group 1 Moderate fuel and heat release
- Ordinary Group 2 Higher ordinary-hazard fuel loading
- Extra Hazard High combustibility or fire growth
- Commodity Product plus packaging and pallet
- Storage arrangement Height, aisles, rack configuration
- Mixed occupancy Evaluate each hazard area
- Design criteria Use adopted edition and occupancy
Wet vs Dry Pipe LA
Wet pipe
- Water in sprinkler piping
- Discharge on sprinkler opening
Dry pipe
- Gas downstream of valve
- Valve admits water after operation
- Check downstream pipe contents
System Selection Checks LA
- Heated piping throughout → Assess wet pipe ( Check project conditions )
- Piping may freeze → Assess dry/preaction ( Check listing and code )
- Detection must control admission → Assess preaction ( Confirm release sequence )
- Open sprinklers required → Assess deluge ( Confirm release sequence )
- Obstruction near sprinkler → Check NFPA 13 ( Deflector and spacing )
- Available pressure falls short → Assess pump/supply ( Compare curves )
System Types LA
- Wet pipe Piping normally contains water
- Dry pipe Downstream gas holds back water
- Preaction Detection participates in valve control
- Deluge Open sprinklers; detection opens valve
- Antifreeze Listed solution under applicable rules
- Standpipe Hose connection water supply
- Fire pump Boosts available supply pressure
- Storage tank Provides dedicated water volume
Preaction vs Deluge LA
Preaction
- Automatic sprinklers
- Detection participates in valve control
Deluge
- Open sprinklers
- Detection opens deluge valve
- Closed sprinklers versus open outlets
Sprinkler Layout LA
- Deflector Sprinkler discharge geometry
- Spacing Check listing and hazard rules
- Coverage area Per-sprinkler protected footprint
- Obstruction Check discharge interference
- Temperature rating Match expected ambient conditions
- Hangers Support pipe to listed criteria
- Seismic bracing Resist applicable seismic movement
- Drainage Provide required system drain path
Hydraulic Path HY
- Outlet → pipe → riser → supply
- Sprinkler flow Pipe friction Elevation Backflow loss Supply curve
Demand vs Supply HY
Demand
- Required flow and pressure
- Includes applicable losses
Supply
- Available flow-pressure curve
- Adjust for pump and losses
- Compare at matching flow
Hydraulic Check Sequence HY
- Occupancy use changes → Reclassify hazard ( Check actual fuel load )
- Density-area method applies → Calculate area demand ( Use adopted criteria )
- Sprinkler flow is known → Solve K-factor pressure ( Q=K√P; matching units )
- Pipe size changes → Recalculate friction ( Track path losses )
- Elevation changes → Adjust pressure ( Track vertical difference )
- Supply test is old → Verify supply data ( Check current flow test )
- Demand exceeds supply → Revise system/supply ( Recheck all required flows )
Hydraulic Chain HY
- K-factor Relates sprinkler flow and pressure
- Q = K√P Gpm, psi; matching US K
- P = (Q/K)² Required sprinkler pressure, psi
- Density × area Density-area method demand setup
- Friction loss Pressure lost through piping
- Elevation Account for vertical pressure change
- Hose allowance Add when governing method requires
- Demand point Flow-pressure required at supply
- Safety margin Difference between supply and demand
Water Supply SU
- Hydrant flow test Static, residual, measured flow
- Supply curve Available pressure by flow
- Backflow loss Device pressure drop
- Pump curve Pressure contribution by flow
- Tank duration Volume against required demand time
- Remote point Critical hydraulic location
- Combined demand Balance simultaneous required flows
- Standpipe demand Apply NFPA 14 component criteria
Project Chain PR
- Survey → criteria → layout → calculate → submit
- Existing conditions Governing edition Working plan Hydraulic proof AHJ review
RFI vs Change Order PR
RFI
- Clarifies existing scope
- Requests design information
Change order
- Alters agreed scope
- Authorizes cost or schedule
- Clarification versus contract modification
Submittal and Coordination PR
- Working plan Show designed system arrangement
- Hydraulic calculations Document demand and supply
- Product data Identify listed selected equipment
- AHJ Enforces adopted local requirements
- RFI Clarify existing project scope
- Change order Authorize changed scope
- Coordination Resolve trade conflicts before installation
- Closeout Turn over approved records
Common Traps
One exam fallacy
- Five separate components ≠ No single WBSL sitting
False aggregate weight
- Component outlines publish ranges ≠ Umbrella weight is unpublished
Scaled versus raw
- 500 is scaled pass point ≠ 500 is not percent correct
Wrong reference edition
- Exam uses listed edition ≠ Local project uses adopted edition
Break clock
- III-H/IV: scheduled break outside ≠ Unscheduled break: clock continues
Dry valve sides
- Gas downstream of valve ≠ Water held upstream
Supply comparison
- Demand at design flow ≠ Supply at matching flow
Last Minute
- 1. Pick your component's official outline
- 2. Level I: 105 questions; 150 minutes
- 3. Level II: 120 questions; 225 minutes
- 4. III-General: 70 questions; 175 minutes
- 5. III-Hydraulics: 60 questions; 240 minutes
- 6. Level IV: 80 questions; 240 minutes
- 7. III-H/IV: 15-minute break outside testing
- 8. Pass point 500 scaled, not percent
- 9. NFPA 13 (2022): all components
- 10. Other references vary by component
- 11. Confirm project-adopted code edition
- 12. Hazard depends on actual contents
- 13. Storage includes product and packaging
- 14. Dry-pipe gas is downstream
- 15. Q=K√P: match US units
- 16. Compare demand/supply at matching flow
- 17. Check friction, elevation, backflow losses
- 18. Submit plans and hydraulic proof
NICET Water-Based Systems Layout
- Practice Questions 204 questions Study Guide 62 topics Cheat Sheet 80 facts Flashcards 50 cards Blogs 1 blog Free CE Podcast