Cheat sheet

SVP Auto Electrician Cheat Sheet

Practice this exam

Workshop Safety and PPE

  • Not published of exam
  • PPE and Isolation High Voltage Safety Hydrogen Explosion Risk Disconnect Order

Circuits, Wiring and Fusing

  • Not published of exam
  • Ohm's Law and Power Circuit Fault Types DIN 72552 Terminals Relay Pin Map Blade Fuse Colours Wire Gauge Sizes

Battery, Charging and Starting

  • Not published of exam
  • Battery Ratings State of Charge Voltage Charging System Starting System

Lighting and Body Electrical

  • Not published of exam
  • Lamp and Beam Basics Body Electrical Control PWM Dimming Bulb Outage Warning

Sensors, ECU and Networks

  • Not published of exam
  • Sensor Types Vehicle Networks ECU Service Rules Five Volt Reference

Test Equipment and Diagnostics

  • Not published of exam
  • Meter Modes Voltage Drop Limits Scan Tool Data DTC Code Format OBD-II Connector Pins

Quick Facts

  • Owner PACC / Takamol / MHRSD
  • Platform pacc.sa
  • Occupation code SSCO 9214013
  • Format Computer test plus practical
  • Time limit Maximum 120 minutes
  • Questions Not published
  • Passing score Not published
  • Domain weights Not published
  • Attempts Up to 3, each paid
  • Fee outside KSA USD 50 per attempt
  • Fee inside KSA SAR 540.50 per attempt
  • Validity 5 years with practical
  • Vehicle system 12 V negative earth

Hazard Response Picker SA

  • Energised electrical fire → CO2 or dry powder ( Isolate supply )
  • Acid in the eyes → Flush 15 minutes ( Never neutralise )
  • Battery gassing hard → Ventilate, kill all sparks
  • Working near an airbag → Wait for capacitor discharge
  • Orange cable in reach → Stop, call HV technician
  • Handling a bare module → Earthed wrist strap

PPE and Isolation SA

  • 12 V burn risk Arc and weld, not shock
  • Rings and watches Metal bridges to earth
  • Disconnect order Negative first, positive last
  • Reconnect order Positive first, negative last
  • Lockout tagout Only the fitter unlocks
  • Charging battery Releases explosive hydrogen gas
  • Acid in the eyes Flush 15 minutes, seek help
  • Electrical fire CO2 or dry powder
  • Airbag work Wait for capacitor discharge

Battery Hazards SA

  • Before moving clamps Switch the charger off
  • Charging bay Ventilate, keep sparks away
  • Spilled acid Neutralise with baking soda
  • Acid on skin Flush with water only
  • Jump start last clamp Engine earth, away from battery
  • Lifting a battery Use a carry strap
  • Damaged or bulging case Do not charge it
  • Gulf heat Shortens battery service life

High Voltage Safety SA

  • Orange cable High voltage, do not touch
  • Automotive high voltage Over 30 VAC or 60 VDC
  • Voltage class A Up to 60 V DC
  • Voltage class B Above 60 V DC
  • Governing standard ISO 6469-3 electrical safety
  • Who may work Trained HV technicians only

Relay Pin Order CI

  • 30 feeds, 85 and 86 coil, 87 out
  • 30: battery feed 85: coil earth 86: coil supply 87: normally open 87a: normally closed

Series vs Parallel CI

Series

  • One path only
  • Current stays same
  • Resistances add up

Parallel

  • Several paths
  • Voltage stays same
  • Total below smallest
  • One path versus many

Circuit Fault Picker CI

  • Fuse blows immediately → Short to ground
  • Load runs on its own → Short to power
  • No voltage at load → Open circuit
  • Dim or slow operation → High resistance
  • Works cold, fails hot → Thermal intermittent
  • Several circuits affected → Shared earth or feed

Ohm's Law and Power CI

  • Ohm's law V = I x R
  • Current I = V / R
  • Resistance R = V / I
  • Power P = V x I
  • Power from current P = I squared R
  • Series resistance Add the resistors up
  • Parallel resistance Less than smallest resistor
  • Series current Same at every point
  • Parallel voltage Same across each branch
  • Kirchhoff current rule In equals out

Ohm's Law Triangle CI

  • V equals I times R
  • I = V / R R = V / I P = V x I

Open vs Short CI

Open

  • No current flows
  • Fuse stays good
  • Load simply dead

Short

  • Excess current flows
  • Fuse blows
  • Wire can burn
  • Dead load versus blown fuse

Circuit Fault Types CI

  • Open circuit No current, load dead
  • Short to ground Fuse blows at once
  • Short to power Load on unexpectedly
  • High resistance Dim, slow, running hot
  • Parasitic draw Key-off current drain
  • Intermittent fault Comes and goes
  • Bad earth Several circuits misbehave

Terminal 87 vs 87a CI

87

  • Normally open
  • Live when energised
  • Load switches on

87a

  • Normally closed
  • Live when resting
  • Load switches off
  • Energised on versus resting on

DIN 72552 Terminals CI

  • 30 Battery positive, unswitched
  • 31 Earth, battery negative
  • 15 Switched positive, ignition on
  • 50 Starter solenoid trigger
  • 54 Stop lamp
  • 55 Fog lamp
  • 56a Main beam
  • 56b Dipped beam
  • 58 Side and tail lamps
  • 61 Charge warning lamp
  • 49 Flasher unit input
  • 49a Flasher unit output
  • B+ Alternator battery output
  • D+ Alternator excitation output
  • W Alternator speed signal
  • L and R Left and right indicators

Relay Pin Map CI

  • 85 Coil earth side
  • 86 Coil supply side
  • 30 Common contact feed
  • 87 Normally open output
  • 87a Normally closed output
  • Coil diode Cathode goes to 86
  • Diode fitted Coil polarity now matters
  • Why a relay Small current switches large

Blade Fuse Colours CI

  • 2 A Grey
  • 3 A Violet
  • 5 A Tan
  • 7.5 A Brown
  • 10 A Red
  • 15 A Blue
  • 20 A Yellow
  • 25 A Clear or natural
  • 30 A Green
  • 40 A Orange

Wire Gauge Sizes CI

  • Lower AWG number Thicker conductor
  • 20 AWG About 0.5 mm2
  • 18 AWG About 0.8 mm2
  • 16 AWG About 1.3 mm2
  • 14 AWG About 2.1 mm2
  • 12 AWG About 3.3 mm2
  • 10 AWG About 5.3 mm2
  • Choosing gauge Current and voltage drop
  • Undersized repair wire Drops voltage, runs hot

Harness Repair Rules CI

  • Preferred joint Correctly crimped terminal
  • Solder in engine bay Stiff joint cracks
  • Sealing a repair Adhesive-lined heat shrink
  • Multiple splices Stagger along the loom
  • After any repair Restore clips and routing
  • Testing a live plug Back-probe, never pierce
  • Connector cleaning Contact cleaner, no abrasives

State of Charge BA

  • 12.6 full, 12.2 half, 11.9 flat
  • 12.65 V: 100 percent 12.24 V: 50 percent 11.89 V: flat Rest four hours

CCA vs Reserve Capacity BA

CCA

  • Cold cranking burst
  • 30 seconds
  • Above 7.2 V

Reserve capacity

  • Minutes at 25 A
  • Down to 10.5 V
  • Alternator dead
  • Start it versus run it

No Crank Diagnosis BA

  • Nothing happens at all → Battery, earths, main feed
  • Rapid clicking → Battery or connections ( Voltage collapses )
  • One solid click → Solenoid or starter ( Contacts or motor )
  • Slow crank, high draw → Drag or internal short
  • Slow crank, low draw → Cables, joints, earths
  • Cranks in neutral only → Park neutral switch
  • Cranks but no start → Immobiliser, fuel or spark

Battery Ratings BA

  • CCA Cranking amps at -18 C
  • CCA cut-off Stays above 7.2 V
  • Reserve capacity Minutes at 25 A
  • Reserve cut-off Down to 10.5 V
  • Amp hours Capacity over 20 hours
  • Cell voltage 2.1 V nominal
  • 12 V battery Six cells in series
  • Full specific gravity About 1.265

Jump Start Order BA

  • Dead plus, good plus, good minus, engine earth
  • Last clamp: engine earth Never the flat negative Remove in reverse order

AGM vs Flooded BA

AGM

  • Sealed, valve regulated
  • No water top-up
  • No equalise charge

Flooded

  • Vented cells
  • Water can be added
  • Equalise charge allowed
  • Sealed needs controlled charging

Charging Fault Picker BA

  • Below 13.5 V running → Alternator or field circuit
  • Above 15 V running → Regulator overcharging
  • AC ripple over limit → Rectifier diode failed
  • Output fine, battery flat → Earth path voltage drop
  • Voltage keeps changing → Smart charging strategy ( Check scan data )
  • Charge lamp stays lit → D+ or excitation circuit

State of Charge Voltage BA

  • 12.65 V 100 percent charged
  • 12.45 V 75 percent charged
  • 12.24 V 50 percent charged
  • 12.06 V 25 percent charged
  • 11.89 V Discharged
  • Rest before reading Four hours minimum
  • Surface charge Load briefly, then read
  • Load test Half CCA, 15 seconds
  • Load test pass 9.6 V at 21 C
  • Conductance tester Works when partly discharged

Charging System BA

  • Typical output 13.5 to 14.5 V
  • Rectifier bridge Three-phase AC to DC
  • Voltage regulator Controls rotor field current
  • AC ripple limit Under 0.5 V AC
  • High AC ripple Failed rectifier diode
  • Temperature compensation Minus 3 mV per cell
  • Hot battery Needs lower charging voltage
  • Smart charging Voltage varies by design
  • Charge lamp lit Charging system not working
  • Good output, flat battery Check the earth path

Starting System BA

  • Pull-in winding Throws pinion, closes contacts
  • Hold-in winding Keeps contacts closed
  • Rapid clicking Supply collapses under load
  • High draw, slow crank Drag or internal short
  • Low draw, slow crank High resistance in circuit
  • Overrunning clutch Stops engine back-driving starter
  • Park neutral switch Blocks crank unless parked
  • Parasitic draw target Under about 50 mA
  • Module sleep time 20 to 60 minutes

Lighting Terminals LI

  • 56 head, 58 side, 54 stop, 55 fog
  • 56a: main beam 56b: dipped beam 58: side and tail 54: stop lamp

Lamp Fault Picker LI

  • One lamp dead → Bulb, socket or earth
  • All lamps dead → Fuse, switch or module
  • Warning after bulb change → Wrong bulb wattage
  • Dim yellow output → Corroded earth point
  • Poor beam after LED → Reflector mismatch

Lamp and Beam Basics LI

  • H4 bulb Twin filament, main and dip
  • H7 bulb Single filament, one beam
  • HID lamp Needs ballast and igniter
  • LED in halogen reflector Scatters, ruins beam cutoff
  • PWM dimming On-time ratio sets brightness
  • Meter on PWM Shows misleading average voltage
  • Bulb outage warning Module measures lamp current
  • Wrong wattage bulb Triggers false outage warning

Body Electrical Control LI

  • Body control module Drives lamps and accessories
  • Dash switch role Low-current input signal
  • Dead lamp circuit Can be a module
  • Shared earth point One fault, many symptoms
  • Window from master only Door switch or wiring
  • Accessory supply Own fused circuit only
  • Amplifier power lead Fuse close to battery

Inductive vs Hall EL

Inductive

  • Two wires
  • Generates own AC
  • Amplitude rises with speed

Hall

  • Three wires
  • Needs a supply
  • Square wave, fixed amplitude
  • Self-powered versus supplied

Network Fault Picker EL

  • One module silent → Its power and earth
  • All modules silent → Bus wiring or termination
  • Resistance not 60 ohms → Termination or bus fault
  • Several sensors implausible → Shared 5 V reference
  • New module fitted → Program and code it

Sensor Types EL

  • Reference supply Typically 5 volts
  • Coolant and air temp NTC thermistor
  • NTC behaviour Hotter means lower resistance
  • Throttle and MAP Three-wire, 0.5 to 4.5 V
  • Narrowband oxygen Switches lean and rich
  • Stoichiometric point About 450 mV
  • Wideband oxygen Read by pump current
  • Inductive crank sensor Two-wire, makes own AC
  • Hall sensor Three-wire, square wave
  • Knock sensor Piezoelectric vibration signal

Vehicle Networks EL

  • High-speed CAN ISO 11898-2, twisted pair
  • Powertrain CAN speed Commonly 500 kbit/s
  • Low-speed CAN ISO 11898-3, 125 kbit/s
  • Termination 120 ohm at each end
  • Bus resistance check About 60 ohms, ignition off
  • CAN High dominant Rises toward 3.5 V
  • CAN Low dominant Falls toward 1.5 V
  • LIN bus Single wire, 20 kbit/s
  • FlexRay 10 Mbit/s, chassis control
  • One module missing Its power, earth, branch
  • Many modules missing Bus wiring or termination

ECU Service Rules EL

  • New module fitted Program and code it
  • Stored adaptations Reset after part change
  • Shared 5 V reference One short affects many
  • Immobiliser Module must match vehicle
  • During coding Hold supply voltage steady
  • Handling a module Earthed wrist strap

Voltage Drop Limits DI

  • 0.2 wire, 0.3 switch, 0.1 earth
  • Cable: 0.2 V Switch: 0.3 V Earth: 0.1 V Test under load

Voltage Drop vs Resistance DI

Voltage drop

  • Circuit under load
  • Finds weak joints
  • Real operating condition

Resistance

  • Circuit dead
  • Component isolated
  • Can pass falsely
  • Loaded truth versus dead reading

Test Tool Picker DI

  • Reading starter current → Clamp meter ( Circuit stays intact )
  • Chasing an intermittent → Oscilloscope ( Shows dropouts )
  • Suspect bad connection → Voltage drop test ( Under load )
  • Checking a PWM output → Duty cycle mode
  • Module output circuit → High-impedance meter ( Never a test lamp )
  • Judging battery condition → Conductance tester
  • Finding key-off drain → Ammeter in series

Meter Modes DI

  • DC volts Parallel across the component
  • Amps In series, move lead
  • Ohms Power off, component isolated
  • Continuity Finds breaks in wire
  • Duty cycle Reads PWM on-time
  • Clamp meter High current, circuit intact
  • Oscilloscope Shows the signal over time
  • Test lamp Power circuits only

Circuit vs Rationality Code DI

Circuit code

  • Outside electrical limits
  • Open or shorted
  • Suspect the wiring

Rationality code

  • Value electrically legal
  • Disagrees with others
  • Suspect drifting sensor
  • Wiring versus drifting sensor

Voltage Drop Limits DI

  • Test condition Circuit loaded and working
  • Across a cable 0.2 V maximum
  • Across a switch 0.3 V maximum
  • At an earth point 0.1 V maximum
  • Whole starter circuit 0.2 to 0.5 V
  • Clean connection Near zero drop
  • Named standard SAE J541 starter circuits

Test Lamp vs Multimeter DI

Test lamp

  • Draws real current
  • Damages module drivers
  • Power circuits only

Digital multimeter

  • High impedance
  • Safe on modules
  • Reads exact value
  • Load versus safe measurement

Scan Tool Data DI

  • Stored DTC Confirmed fault in memory
  • Pending DTC Seen this drive cycle
  • Permanent DTC Clears only after repair
  • Freeze frame Conditions when code set
  • Live data What sensors report now
  • Codes versus data Area, then present fault
  • Bidirectional test Command the actuator directly

DTC Code Format DI

  • P Powertrain
  • B Body
  • C Chassis
  • U Network communication
  • Second character 0 Generic, SAE defined
  • Second character 1 Manufacturer specific
  • Circuit code Outside electrical limits
  • Rationality code Legal value, illogical reading

OBD-II Connector Pins DI

  • Pin 16 Battery positive, unswitched
  • Pin 4 Chassis ground
  • Pin 5 Signal ground
  • Pin 6 CAN High
  • Pin 14 CAN Low
  • Pin 7 K-line, ISO 9141
  • Connector location Within the driver's reach

Common Traps

Fuse protects the wire

  • It guards the harness ≠ Not the load device

Coil versus contacts

  • 85 and 86 are coil ≠ 30 and 87 carry load

Resting volts versus load

  • Surface charge reads high ≠ Load test finds truth

Ohms versus voltage drop

  • Dead resistance can pass ≠ Loaded drop reveals fault

Codes do not name parts

  • A code names a circuit ≠ Live data confirms it

Charging voltage is not fixed

  • Smart systems vary output ≠ Judge against maker strategy

Bulb fits, beam fails

  • LED fits the socket ≠ Reflector still expects filament

One module versus the bus

  • One silent means branch ≠ All silent means bus

12 volts is not harmless

  • Shock risk is low ≠ Short circuit energy high

Bigger fuse is not a fix

  • Wire becomes the fuse ≠ Find the real fault

Last Minute

  • 1. Weights and pass mark: not published
  • 2. Relay: 30 feed, 87 out
  • 3. 85 and 86 are coil
  • 4. Fuse protects wire, not load
  • 5. Lower AWG number, thicker wire
  • 6. 12.65 V rested equals full
  • 7. Load test: 9.6 V minimum
  • 8. Charging: 13.5 to 14.5 V
  • 9. AC ripple under 0.5 V
  • 10. Drop: 0.2 wire, 0.3 switch
  • 11. CAN termination reads 60 ohms
  • 12. NTC: hotter means lower resistance
  • 13. Orange cable equals high voltage
  • 14. Negative off first, on last
  • 15. Never test lamp on modules
  • 16. Rationality code: sensor has drifted

Saudi Skill Verification Program - Auto Electrician

  • Practice Questions 152 questions Study Guide 43 topics Cheat Sheet 206 facts Flashcards 50 cards Shorts 1 short Podcast

Same family resources

  • Explore More Saudi SVP Automotive Skill Verification
  • Continue into nearby exams from the same family. Each card keeps practice questions, study guides, flashcards, videos, and articles in one place.

Saudi Skill Verification Program - Light Vehicle Mechanic

  • Practice Questions 162 questions Study Guide 43 topics Shorts 2 short s

Saudi Skill Verification Program - Diesel / Heavy Vehicle Mechanic

  • Practice Questions 100 questions Shorts 1 short