Study guide

5.3 Stimulators, Polarity, and Stimulation Pitfalls

Registered Nerve Conduction Studies Technologist R.NCS.T.

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview

1.1 Current Exam Facts 1.2 Eligibility, Documentation, and Application 1.3 Scoring, Recertification, and Test Day

2 Membrane Physiology and Action Potentials

2.1 Resting Membrane Potential and Cell Membrane Physiology 2.2 Action Potential Phases, All-or-None Response, and Refractory Periods 2.3 Saltatory Conduction, Myelin, and Nodes of Ranvier

3 Peripheral Nerve Structure and Cell Bodies

3.1 Fascicles and Nerve Connective Tissues 3.2 Peripheral Nerve Fiber Types 3.3 Motor and Sensory Cell-Body Locations

4 Muscle Physiology, Roots, and Plexuses

4.1 Skeletal Muscle Structure: Myofibrils, Sarcomeres, and Bands 4.2 Excitation-Contraction Coupling 4.3 Spinal Roots, Dorsal and Ventral Roots, and Rami 4.4 Brachial and Lumbosacral Plexus Organization

5 Electronics, Instrumentation, and Stimulation

5.1 Ohm’s Law, AC/DC Circuits, and Resistance 5.2 Amplifiers, Filters, Averaging, and Display Settings 5.3 Stimulators, Polarity, and Stimulation Pitfalls

6 Waveform Parameters, Conduction Velocity, and Pediatric NCS

6.1 Latency, Amplitude, Duration, Area, and Rise Time 6.2 Conduction Velocity Calculation and Normal Values 6.3 Pediatric Nerve Conduction Studies

7 Lesion Patterns and Wallerian Degeneration

7.1 Preganglionic versus Postganglionic Lesions 7.2 Focal Lesions, Conduction Block, Demyelination, and Temporal Dispersion 7.3 Axonal Loss, Wallerian Degeneration, and Nerve-Injury Grades

8 Late Responses and the Blink Reflex

8.1 F Waves: Origin, Technique, and Clinical Use 8.2 H Reflexes: Origin, Technique, and Clinical Use 8.3 A Waves and the Blink Reflex

9 NMJ Physiology and Repetitive Nerve Stimulation

9.1 Neuromuscular Junction Anatomy and Physiology 9.2 Repetitive Nerve Stimulation: Technical Setup 9.3 Post-Activation Facilitation, Exhaustion, and Pseudofacilitation

10 Neuromuscular Junction Disorders

10.1 Myasthenia Gravis (Postsynaptic) 10.2 Lambert-Eaton Myasthenic Syndrome 10.3 Botulism and Presynaptic Toxin Patterns

11 Upper-Extremity Nerve Conduction Protocols

11.1 Median Motor, Sensory, AIN, and Palmar Cutaneous Studies 11.2 Ulnar Motor, Sensory, Dorsal Ulnar Cutaneous, and Medial Antebrachial Studies 11.3 Radial Motor, Posterior Interosseous, and Superficial Radial Studies

12 Upper-Extremity Entrapments and Mononeuropathies

12.1 Median Neuropathy at the Wrist (Carpal Tunnel) 12.2 Ulnar Neuropathy at the Elbow and Guyon’s Canal 12.3 Radial Neuropathy (Saturday Night Palsy) and Related UE Mononeuropathies

13 Lower-Extremity Nerve Conduction Protocols

13.1 Common, Deep, and Superficial Fibular (Peroneal) Studies 13.2 Tibial Motor and Medial/Lateral Plantar Studies 13.3 Sural, Saphenous, and Lateral Femoral Cutaneous Studies

14 Lower-Extremity Neuropathies and Proximal Nerves

14.1 Fibular Neuropathy at the Fibular Head versus L5 Radiculopathy 14.2 Tarsal Tunnel, Tibial Neuropathy, and S1 Localization 14.3 Femoral, Sciatic, and Lateral Femoral Cutaneous Neuropathies

15 Cranial Nerves, Other Nerves, and Plexus Lesions

15.1 Cranial Nerves with Facial, Trigeminal, and Accessory Studies 15.2 Phrenic, Suprascapular, Long Thoracic, and Axillary Nerves 15.3 Plexus Lesions: Erb’s Palsy, Neurogenic TOS, and Parsonage-Turner

16 Root, Motor Neuron, Polyneuropathy, and Muscle Disorders

16.1 Radiculopathy, Root Avulsion, and Sensory Neuronopathy 16.2 Motor Neuron Disease and Multifocal Motor Neuropathy 16.3 Polyneuropathies, Mononeuropathy Multiplex, and Muscle Disorders

17 Temperature, Age, Height, and Martin-Gruber Anastomosis

17.1 Temperature Effects and Warming Methods 17.2 Age and Height Effects on Nerve Conduction 17.3 Martin-Gruber Anastomosis Patterns

18 Anomalous Innervation, Technical Factors, and Safety

18.1 Riche-Cannieu Anastomosis and Accessory Fibular Nerve 18.2 Technical Factors and Troubleshooting Abnormal Studies 18.3 Infection Control, Electrical Safety, HIPAA, and OSHA

5.3 Stimulators, Polarity, and Stimulation Pitfalls

Key Takeaways Explain This Topic AI

Constant-current stimulators vary voltage to hold current as impedance changes; constant-voltage stimulators let current fall when resistance rises (I = V / R)

The cathode (black, negative) depolarizes; for orthodromic motor studies it should face the recording site — cathode distal at distal stimulation sites

Anodal Block occurs when the anode lies between the cathode and the recording electrodes and hyperpolarization stops propagation

Submaximal stimulation underestimates amplitude; overstimulation co-stimulates adjacent nerves

  • Volume conduction can make a far-field bump look like a SNAP or CMAP component
  • Last updated: September 2026

The stimulator is the other half of Ohm’s law: it forces current through tissue so axons reach threshold. Domain II.D of the American Association of Electrodiagnostic Technologists (AAET) Registered Nerve Conduction Study Technologist (R.NCS.T.) outline asks you to know how the box delivers that current, which pole depolarizes, and which setup errors shrink, delay, or fake a response. This ExamFinch section is independent teaching on stimulators, polarity, Anodal Block , volume conduction, artifact, and supramaximal technique.

Constant current versus constant voltage

Two stimulator designs appear on laboratory equipment:

A constant-current stimulator varies its output voltage as electrode-skin resistance changes so that the current you selected (for example 25 mA) stays the same — until the device reaches its compliance voltage and can no longer compensate (Section 5.1). Because nerve depolarization depends on current density in tissue, constant current is the usual NCS choice.

A constant-voltage stimulator holds voltage . Current then follows Ohm’s law: I = V / R . If paste dries and R rises, current falls and the stimulus becomes submaximal without a knob change. If R falls (sweat, extra gel), current rises and you may overstimulate.

If amplitudes swing when you reseat a cathode, ask which mode you are in and what the impedance did. Do not first assume the patient “tried less.” Watch the displayed milliamperes on a constant-voltage unit; they are the true stimulus, not the voltage setting.

Intensity, duration, and threshold

You have two main stimulus parameters:

Intensity (mA in constant-current mode, or V in constant-voltage mode) — how strong each pulse is.

Duration (pulse width), commonly about 0.05–0.2 milliseconds (50–200 microseconds) as a teaching range for routine NCS, with about 0.1 ms a frequent starting width. Longer pulses recruit with less intensity but enlarge artifact and can increase discomfort.

Rheobase and chronaxie are strength-duration ideas: a very short pulse needs more current; a longer pulse can use less. For daily NCS you rarely plot a full strength-duration curve, but you use the idea when a nerve is deep: lengthen duration slightly rather than endlessly cranking intensity into co-stimulation territory.

Intensity without a plateau is not a complete stimulus description. The same 30 mA may be supramaximal for a superficial sensory nerve and inadequate for a deep motor nerve, or excessive for a neighbor nerve at the wrist.

Polarity: cathode and anode

A bipolar stimulator has two poles:

Cathode : negative pole. Conventionally black . The cathode depolarizes nearby axons (makes the outside of the membrane less positive, moving the nerve toward threshold). The recorded impulse starts under the cathode.

Anode : positive pole. Conventionally red . The anode hyperpolarizes nearby axons (makes firing less likely).

For orthodromic motor studies (stimulus on nerve, recording over muscle in the natural direction of motor axons), the depolarizing cathode should face the recording site . At a distal stimulation site (wrist, ankle), that orientation is cathode distal , anode proximal. The cathode sits closer to the muscle; the anode sits further up the limb. If you reverse the banana plugs, you reverse the poles even if the handheld probe still “looks” pointed the right way. Color coding only helps if black is actually plugged into the cathode jack.

Latency is measured from the stimulus trigger, but the nerve fires under the cathode . Moving the cathode 2–3 cm farther from the muscle lengthens latency by the conduction time of that extra distance, even if intensity is unchanged.

Anodal Block

Anodal Block is the handbook name for a classic polarity error. If the anode lies between the cathode and the recording electrodes , the impulse born under the cathode must pass under the hyperpolarizing anode to reach the muscle. Hyperpolarization can block propagation. The CMAP shrinks, becomes inconsistent, or vanishes at intensities that should have been adequate. The fix is not “more milliamps first”; it is restoring cathode-toward-the-muscle orientation and then repeating a supramaximal series.

Reversed polarity therefore contaminates both amplitude (block, incomplete recruitment) and latency (cathode no longer at the intended site). A small, late CMAP after a plug swap is a polarity problem until you have ruled it out. Write Anodal Block the way handbooks do when a stem uses that name; do not invent a softer synonym on the exam if the question already used the term.

Supramaximal stimulation versus submaximal and overstimulation

Increase intensity until the CMAP or SNAP amplitude plateaus , then add a modest increment (many laboratories teach about 20% above the intensity that first produces that plateau). That is supramaximal stimulation : all axons in the nerve that can be recruited from that site are firing, so amplitude reflects the nerve, not the knob.

Submaximal stimulation leaves axons silent. Amplitude is underestimated . Latency may also be wrong if the remaining fibers are not the fastest ones. Never report a small CMAP as axonal loss until you have proved the stimulus was supramaximal. A “repeatable” small response can still be submaximal if you stopped climbing too early.

Overstimulation does not usefully enlarge a plateaued CMAP. Extra current volume-conducts to neighboring nerves and muscles. Median wrist stimulation that is too strong co-stimulates ulnar fibers; fibular (peroneal) stimulation at the knee can spread to tibial fibers. A bonus bump on the tracing may be the wrong nerve. Back down to the true plateau and confirm cathode position on the target nerve.

Supramaximal is a physiologic end-point (plateau plus a small extra), not a fixed milliampere number that works for every limb and every edema.

Stimulus artifact

Stimulus artifact is the electrical spike of the pulse appearing at the recording electrodes. It is worse with high impedance, long pulse duration, high intensity, poor cathode orientation, widely spread recording leads, and stimulator-to-recorder cable proximity. Artifact can overlay SNAP onset, especially in short distal segments (for example palmar or plantar studies).

Reduce it with the Ohm’s law hygiene from Section 5.1, correct polarity, shorter duration when recruitment still reaches plateau, rotating the stimulator slightly, and physically separating stimulator cables from recording cables. Remember from Section 5.2: averaging will not cancel time-locked artifact. An averaged early spike that is too soon to be a SNAP is still artifact.

Volume conduction

The body is a volume conductor : current spreads through extracellular fluid, not only along the nerve you aimed at. Consequences for the technologist:

A far-field potential generated at a distance can appear under your recording electrodes and look like a SNAP or CMAP component .

Co-stimulated muscle can inject a volume-conducted CMAP into a sensory channel.

An initial positivity may be volume conduction from a nearby generator rather than a finding you should measure as the nerve of interest.

Ask whether the putative response has the latency, morphology, and montage behavior of the nerve under study . If moving the stimulator off the nerve kills a true SNAP but a far-field bump remains, you were looking at volume conduction. If a “sensory” potential is millivolts tall, suspect a volume-conducted muscle response until proven otherwise.

Volume conduction is also how overstimulation reaches the neighbor nerve. The current does not stay in a neat cylinder under the cathode; it spreads. That is useful (you can still stimulate a slightly deep nerve) and dangerous (you can stimulate two nerves at once).

Pitfalls table

Pitfall What you see What to do

Reversed polarity / Anodal Block Small, unstable, or absent CMAP; unexpectedly long latency Cathode toward recording site (cathode distal at distal motor sites); then re-establish a plateau

Submaximal stimulus Low amplitude; possibly odd latency Increase intensity or duration until amplitude plateaus, then add a modest extra increment

Overstimulation / co-stimulation Extra bumps; unexpected amplitude; crossover from a neighbor nerve Return to the true plateau; reposition the cathode on the target nerve

High-impedance artifact Large shock spike overlaying onset Lower electrode-skin impedance; shorten duration if still recruiting

Volume-conducted far-field A bump that does not behave like the nerve of interest Change site or montage; confirm the response vanishes off-nerve

Constant-voltage mode plus rising R Quietly shrinking responses mid-study Recheck paste and contacts; prefer constant current for NCS

Measuring artifact as a SNAP Tiny early spike, often too early to be biologic Do not average it into existence; fix setup first

Mastering stimulation is not theatrical high milliamperes. It is delivering a known current, at a known pole, to the intended nerve, without recruiting the neighbor, without blocking at the anode, and without mistaking a far-field bump for physiology.

Loading diagram... Correct distal motor polarity versus Anodal Block