Study guide

6.2 Lift Station Hydraulics, Pumping Rate & Drawdown Math

ABC Wastewater Collection Operator Class I Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Gravity Sewers, System Components & Materials

1.1 Gravity Sewer Principles & System Layout 1.2 Sewer Pipe Materials, Sizing & Joining Methods 1.3 Manholes, Drop Structures & Appurtenances 1.4 Gravity Sewer Hydraulics, Slope & Scour Velocity

2 Chapter 2: Lift Stations, Pumping Systems & Force Mains

2.1 Lift Station Design: Wet Well vs Dry Well Systems 2.2 Wastewater Pumps & Operating Principles 2.3 Level Controls, Pump Sequencing & SCADA Telemetry 2.4 Force Mains, Valves & Surge Protection 2.5 Lift Station Emergency Power, Maintenance & Operation

3 Chapter 3: Sewer Inspection, Testing & Cleaning

3.1 Hydraulic Jetting & High-Velocity Cleaning 3.2 Mechanical Rodding, Bucketing & Clearing Methods 3.3 Closed-Circuit Television (CCTV) Inspection & NASSCO PACP 3.4 Sewer Testing Methods: Smoke, Dye & Acoustic 3.5 Root, Grease & Debris Management

4 Chapter 4: Inflow & Infiltration (I/I), SSOs & FOG Management

4.1 Inflow vs Infiltration Fundamentals & RDII 4.2 Sanitary Sewer Overflows (SSOs) & Combined Sewer Overflows (CSOs) 4.3 SSO Emergency Response, Containment & NPDES Reporting 4.4 Fats, Oils, and Grease (FOG) Control Programs 4.5 Sewer System Rehabilitation & Trenchless Methods

5 Chapter 5: Safety, Confined Space Entry & Environmental Hazards

5.1 OSHA 1910.146 Permit-Required Confined Space Standards 5.2 Atmospheric Testing, Monitoring & Calibration Sequence 5.3 Ventilation, PPE & Emergency Rescue Equipment 5.4 Hydrogen Sulfide (H2S), Toxic Gases & Crown Corrosion 5.5 Trenching, Excavation & Traffic Safety (MUTCD & 811)

6 Chapter 6: Operator Math, Hydraulics & System Administration

6.1 Flow, Velocity & Cross-Sectional Area Calculations 6.2 Lift Station Hydraulics, Pumping Rate & Drawdown Math 6.3 Sewer Slope, Invert Elevations & Grade Calculations 6.4 Chemical Dosing, Feed Rate & Quantity Calculations 6.5 Regulatory Framework, Recordkeeping & System Mapping

7 Chapter 7: Equipment Operation, Tools & Preventive Maintenance

7.1 Gas Detectors, Flow Meters & Blowers: Operation and Calibration 7.2 Balling, Flushing, Poly Pigs & Cleaning-Method Selection 7.3 Heavy Equipment, Excavation & Hydro Excavation 7.4 Electrical Equipment: VFDs, Motor Control Centers & Low-Voltage Devices 7.5 Preventive Maintenance Programs, SOP/OEM Compliance & Support Tools

8 Chapter 8: System Restoration, Mapping & Emergency Operations

8.1 Manhole, Tap & Lateral Rehabilitation and Exfiltration Control 8.2 Appurtenance Inspection: Air Release Valves, Siphons, Regulators & Outfalls 8.3 Blueprints, GIS, Asset Management & System Mapping 8.4 Emergency Bypass Pumping & System Failure Response 8.5 New Pipe Installation Inspection & Acceptance Testing

9 Chapter 9: Monitoring, Safety Programs & System Administration

9.1 Flow Monitoring, Flow Meters & Sensor Calibration 9.2 Wastewater Characteristics & Abnormal Discharge Identification 9.3 Chemical Handling, Inventory, Feed Systems & Spill Response 9.4 Electrical Safety, Lockout/Tagout, Fire Safety & Occupational Health 9.5 Customer Service, Safety Programs, Operator Training & Regulatory Administration

6.2 Lift Station Hydraulics, Pumping Rate & Drawdown Math

Key Takeaways Explain This Topic AI

Wet well volume is calculated based on geometry: rectangular wet wells use V = L × W × H × 7.48 gal/cu ft, while cylindrical wet wells use V = 0.7854 × D² × H × 7.48 gal/cu ft.

A true pump drawdown test must account for continuous sewer inflow: Total Pump Capacity (gpm) = (Net Volume Pumped / Pump Run Time) + Inflow Rate (gpm).

Total lift station operating cycle time equals the sum of wet well fill time and pump drawdown time (T = t_fill + t_pump), directly determining motor starts per hour.

Water Horsepower represents actual useful hydraulic work (WHP = (Q_gpm × TDH_ft) / 3960), while Brake Horsepower (BHP = WHP / pump efficiency) and Motor Horsepower (MHP = BHP / motor efficiency) account for mechanical and electrical losses.

Last updated: September 2026

6.2 Lift Station Hydraulics, Pumping Rate & Drawdown Math

Exam Focus: Operators must be capable of calculating wet well holding capacity, performing volumetric pump drawdown calibrations accounting for continuous sewer inflow, computing pump cycle times, and determining water horsepower ( WHP \text{WHP} WHP ), brake horsepower ( BHP \text{BHP} BHP ), and daily power costs.

Wet Well Geometry & Volumetric Capacity

Lift station wet wells provide temporary storage to buffer incoming wastewater surges between pump cycles. Calculating the volume per foot of depth allows operators to determine storage capacity, set level control floats, and conduct drawdown testing. WET WELL VOLUMETRIC CONFIGURATIONS

  • Rectangular Wet Well Cylindrical Wet Well
  • +--------------------+ /--------------------\
  • / /| | |
  • +--------------------+ | | |
  • | | | H (Depth) | | H (Depth)
  • | | | | |
  • | L (Length) |/ | D (Diameter) |
  • +--------------------+ \--------------------/
  • W (Width)
  • V = L × W × H × 7.48 gal/cu ft V = 0.7854 × D² × H × 7.48 gal/cu ft

1. Rectangular Wet Wells V cu ft = L × W × H \mathbf{V_{\text{cu ft}} = L \times W \times H} V cu ft ​ = L × W × H V gallons = L × W × H × 7.48 gal/cu ft \mathbf{V_{\text{gallons}} = L \times W \times H \times 7.48\text{ gal/cu ft}} V gallons ​ = L × W × H × 7.48 gal/cu ft Gallons per Foot of Depth = L × W × 7.48 \text{Gallons per Foot of Depth} = L \times W \times 7.48 Gallons per Foot of Depth = L × W × 7.48 Gallons per Inch of Depth = L × W × 7.48 12 \text{Gallons per Inch of Depth} = \frac{L \times W \times 7.48}{12} Gallons per Inch of Depth = 12 L × W × 7.48 ​

2. Cylindrical (Round) Wet Wells V cu ft = 0.7854 × D 2 × H \mathbf{V_{\text{cu ft}} = 0.7854 \times D^2 \times H} V cu ft ​ = 0.7854 × D 2 × H V gallons = 0.7854 × D 2 × H × 7.48 gal/cu ft \mathbf{V_{\text{gallons}} = 0.7854 \times D^2 \times H \times 7.48\text{ gal/cu ft}} V gallons ​ = 0.7854 × D 2 × H × 7.48 gal/cu ft Gallons per Foot of Depth = 0.7854 × D 2 × 7.48 \text{Gallons per Foot of Depth} = 0.7854 \times D^2 \times 7.48 Gallons per Foot of Depth = 0.7854 × D 2 × 7.48 Gallons per Inch of Depth = 0.7854 × D 2 × 7.48 12 \text{Gallons per Inch of Depth} = \frac{0.7854 \times D^2 \times 7.48}{12} Gallons per Inch of Depth = 12 0.7854 × D 2 × 7.48 ​

The Pump Drawdown Test

A drawdown test is the standard field method used by operators to determine the actual pumping capacity of a wastewater pump under field operating conditions. Because raw sewage continuously enters the wet well from the collection network during testing, operators must perform a two-step test to account for inflow. PUMP DRAWDOWN TEST SEQUENCE

  • STEP 1: INFLOW RATE TEST STEP 2: DRAWDOWN TEST
  • (All Pumps OFF) (Lead Pump ON)
  • +---------------------------+ +---------------------------+
  • | Inflow (Qin) ---> [ ] | | Inflow (Qin) ---> [ ] |
  • | | | |
  • | ↑ Liquid Rises (ΔH_in) | | ↓ Liquid Drops (ΔH_out) |
  • |~~~~~~~~~~~~~~~~~~~~~~~~~~~| |~~~~~~~~~~~~~~~~~~~~~~~~~~~|
  • | | | =====> [PUMP ON] ====> |
  • +---------------------------+ +---------------------------+
  • Qin = Vol_rise / Time_in Qnet = Vol_drop / Time_pump
  • TOTAL PUMP DISCHARGE: Qpump = Qnet + Qin
  • Step-by-Step Drawdown Procedure

Step 1 — Measure Inflow Rate ( Q in Q_{\text{in}} Q in ​ ):

Turn all pumps OFF .

Record the time ( t in t_{\text{in}} t in ​ in minutes) it takes for incoming sewage to raise the wet well water level by a measured distance ( Δ H in \Delta H_{\text{in}} Δ H in ​ in feet).

Calculate inflow volume: V in = Area × Δ H in × 7.48 V_{\text{in}} = \text{Area} \times \Delta H_{\text{in}} \times 7.48 V in ​ = Area × Δ H in ​ × 7.48 .

Calculate inflow rate: Q in = V in / t in Q_{\text{in}} = V_{\text{in}} / t_{\text{in}} Q in ​ = V in ​ / t in ​ (in gpm \text{gpm} gpm ).

Step 2 — Measure Net Pumping Rate ( Q net Q_{\text{net}} Q net ​ ):

Turn the test pump ON (with inflow still occurring).

Record the time ( t pump t_{\text{pump}} t pump ​ in minutes) required for the pump to draw down the water level by a measured distance ( Δ H drop \Delta H_{\text{drop}} Δ H drop ​ in feet).

Calculate net volume pumped: V drop = Area × Δ H drop × 7.48 V_{\text{drop}} = \text{Area} \times \Delta H_{\text{drop}} \times 7.48 V drop ​ = Area × Δ H drop ​ × 7.48 .

Calculate net drawdown rate: Q net = V drop / t pump Q_{\text{net}} = V_{\text{drop}} / t_{\text{pump}} Q net ​ = V drop ​ / t pump ​ (in gpm \text{gpm} gpm ).

Step 3 — Compute Total Pumping Capacity ( Q pump Q_{\text{pump}} Q pump ​ ): Q pump = Q net + Q in = ( V drop t pump ) + Q in \mathbf{Q_{\text{pump}} = Q_{\text{net}} + Q_{\text{in}} = \left(\frac{V_{\text{drop}}}{t_{\text{pump}}}\right) + Q_{\text{in}}} Q pump ​ = Q net ​ + Q in ​ = ( t pump ​ V drop ​ ​ ) + Q in ​

Class I Exam Trap: Never calculate pump output by simply dividing the drawdown volume by time. If you ignore the inflow entering during the test, you will significantly underestimate pump capacity.

Pump Cycle Time & Starts per Hour

Frequent motor starts cause excessive heat buildup and premature motor winding failure. Designers typically limit lift station pump starts to 4 to 6 starts per hour 4\text{ to }6\text{ starts per hour} 4 to 6 starts per hour .

Fill Time ( t fill t_{\text{fill}} t fill ​ ): Time required for incoming flow ( Q in Q_{\text{in}} Q in ​ ) to fill the operating volume ( V op V_{\text{op}} V op ​ ) between lead-off and lead-on float levels: t fill = V op Q in t_{\text{fill}} = \frac{V_{\text{op}}}{Q_{\text{in}}} t fill ​ = Q in ​ V op ​ ​

Pump Down Time ( t pump t_{\text{pump}} t pump ​ ): Time required for the pump to evacuate the operating volume while inflow continues: t pump = V op Q pump − Q in t_{\text{pump}} = \frac{V_{\text{op}}}{Q_{\text{pump}} - Q_{\text{in}}} t pump ​ = Q pump ​ − Q in ​ V op ​ ​

Total Operating Cycle Time ( T T T ): T = t fill + t pump T = t_{\text{fill}} + t_{\text{pump}} T = t fill ​ + t pump ​

Pump Starts per Hour: Starts per Hour = 60 minutes/hour T (minutes) \text{Starts per Hour} = \frac{60\text{ minutes/hour}}{T\text{ (minutes)}} Starts per Hour = T (minutes) 60 minutes/hour ​

Horsepower, Efficiency & Energy Math

Pumping wastewater requires mechanical energy to overcome elevation differences ( static head ) and pipe friction ( friction head ), collectively known as Total Dynamic Head (TDH) . PUMP HORSEPOWER CONVERSION CASCADE

  • Electrical Grid Input Motor Output / Shaft Liquid Work Done
  • +--------------------+ +--------------------+ +--------------------+
  • | Motor Horsepower | ------>| Brake Horsepower | ------>| Water Horsepower |
  • | (MHP) | η_motor| (BHP) | η_pump| (WHP) |
  • +--------------------+ +--------------------+ +--------------------+
  • MHP = BHP / η_motor BHP = WHP / η_pump WHP = (Q × TDH)/3960
  • 1. Water Horsepower (WHP)

Water horsepower is the actual theoretical power imparted directly to the wastewater stream: W H P = Q gpm × TDH ft 3 , 960 \mathbf{WHP = \frac{Q_{\text{gpm}} \times \text{TDH}_{\text{ft}}}{3,960}} WHP = 3 , 960 Q gpm ​ × TDH ft ​ ​

(The constant 3 , 960 3,960 3 , 960 is derived from 33 , 000 ft-lbs/min per HP / 8.34 lbs/gal 33,000\text{ ft-lbs/min per HP} / 8.34\text{ lbs/gal} 33 , 000 ft-lbs/min per HP /8.34 lbs/gal .)

2. Brake Horsepower (BHP)

Brake horsepower is the actual mechanical horsepower delivered by the electric motor shaft to the pump impeller, accounting for hydraulic and friction losses inside the pump casing (pump efficiency η pump \eta_{\text{pump}} η pump ​ ): B H P = WHP η pump = Q gpm × TDH ft 3 , 960 × η pump \mathbf{BHP = \frac{\text{WHP}}{\eta_{\text{pump}}} = \frac{Q_{\text{gpm}} \times \text{TDH}_{\text{ft}}}{3,960 \times \eta_{\text{pump}}}} BHP = η pump ​ WHP ​ = 3 , 960 × η pump ​ Q gpm ​ × TDH ft ​ ​

3. Motor Horsepower (MHP) / Wire-to-Water Efficiency

Motor horsepower represents the total electrical power drawn from the electrical grid, accounting for motor electrical losses (motor efficiency η motor \eta_{\text{motor}} η motor ​ ): M H P = BHP η motor = WHP η pump × η motor = WHP η wire-to-water \mathbf{MHP = \frac{\text{BHP}}{\eta_{\text{motor}}} = \frac{\text{WHP}}{\eta_{\text{pump}} \times \eta_{\text{motor}}} = \frac{\text{WHP}}{\eta_{\text{wire-to-water}}}} MHP = η motor ​ BHP ​ = η pump ​ × η motor ​ WHP ​ = η wire-to-water ​ WHP ​

Where: η wire-to-water = η pump × η motor \eta_{\text{wire-to-water}} = \eta_{\text{pump}} \times \eta_{\text{motor}} η wire-to-water ​ = η pump ​ × η motor ​

4. Electrical Power Consumption & Cost

Kilowatt Demand ( kW \text{kW} kW ): kW = BHP × 0.746 or kW = MHP × 0.746 η motor \text{kW} = \text{BHP} \times 0.746 \quad \text{or} \quad \text{kW} = \frac{\text{MHP} \times 0.746}{\eta_{\text{motor}}} kW = BHP × 0.746 or kW = η motor ​ MHP × 0.746 ​

Daily Electrical Energy Consumption ( kWh/day \text{kWh/day} kWh/day ): kWh/day = kW × Hours Operated per Day \text{kWh/day} = \text{kW} \times \text{Hours Operated per Day} kWh/day = kW × Hours Operated per Day

Daily Electrical Cost: Daily Cost = kWh/day × Electrical Rate per kWh \text{Daily Cost} = \text{kWh/day} \times \text{Electrical Rate per kWh} Daily Cost = kWh/day × Electrical Rate per kWh

  • Step-by-Step Worked Lift Station Problems
  • Problem 1: Volumetric Drawdown Test

Question: A cylindrical wet well has a diameter of 10.0 ft 10.0\text{ ft} 10.0 ft . With the lead pump operating for 5.0 minutes 5.0\text{ minutes} 5.0 minutes , the water level drops exactly 2.50 ft 2.50\text{ ft} 2.50 ft . A prior test established that raw sewage continuously flows into the wet well at 120 gpm 120\text{ gpm} 120 gpm . Calculate the total pumping capacity of the lead pump in gpm \text{gpm} gpm .

Step 1: Calculate wet well cross-sectional area: A = 0.7854 × D 2 = 0.7854 × ( 10.0 ft ) 2 = 78.54 sq ft A = 0.7854 \times D^2 = 0.7854 \times (10.0\text{ ft})^2 = 78.54\text{ sq ft} A = 0.7854 × D 2 = 0.7854 × ( 10.0 ft ) 2 = 78.54 sq ft

Step 2: Calculate net volume drawn down: V drop = 78.54 sq ft × 2.50 ft × 7.48 gal/cu ft = 196.35 cu ft × 7.48 = 1 , 468.7 gallons V_{\text{drop}} = 78.54\text{ sq ft} \times 2.50\text{ ft} \times 7.48\text{ gal/cu ft} = 196.35\text{ cu ft} \times 7.48 = 1,468.7\text{ gallons} V drop ​ = 78.54 sq ft × 2.50 ft × 7.48 gal/cu ft = 196.35 cu ft × 7.48 = 1 , 468.7 gallons

Step 3: Calculate net pumping rate ( Q net Q_{\text{net}} Q net ​ ): Q net = 1 , 468.7 gallons 5.0 minutes = 293.7 gpm Q_{\text{net}} = \frac{1,468.7\text{ gallons}}{5.0\text{ minutes}} = 293.7\text{ gpm} Q net ​ = 5.0 minutes 1 , 468.7 gallons ​ = 293.7 gpm

Step 4: Calculate total pump capacity ( Q pump = Q net + Q in Q_{\text{pump}} = Q_{\text{net}} + Q_{\text{in}} Q pump ​ = Q net ​ + Q in ​ ): Q pump = 293.7 gpm + 120.0 gpm = 413.7 gpm ≈ 414 gpm Q_{\text{pump}} = 293.7\text{ gpm} + 120.0\text{ gpm} = \mathbf{413.7\text{ gpm}} \approx \mathbf{414\text{ gpm}} Q pump ​ = 293.7 gpm + 120.0 gpm = 413.7 gpm ≈ 414 gpm

Problem 2: Water Horsepower Calculation

Question: A submersible lift station pump delivers 500 gpm 500\text{ gpm} 500 gpm against a total dynamic head (TDH) of 60.0 feet 60.0\text{ feet} 60.0 feet . Calculate the Water Horsepower ( WHP \text{WHP} WHP ).

Step 1: Apply WHP formula: WHP = Q gpm × TDH ft 3 , 960 = 500 gpm × 60.0 ft 3 , 960 = 30 , 000 3 , 960 = 7.58 WHP ≈ 7.6 WHP \text{WHP} = \frac{Q_{\text{gpm}} \times \text{TDH}_{\text{ft}}}{3,960} = \frac{500\text{ gpm} \times 60.0\text{ ft}}{3,960} = \frac{30,000}{3,960} = \mathbf{7.58\text{ WHP}} \approx \mathbf{7.6\text{ WHP}} WHP = 3 , 960 Q gpm ​ × TDH ft ​ ​ = 3 , 960 500 gpm × 60.0 ft ​ = 3 , 960 30 , 000 ​ = 7.58 WHP ≈ 7.6 WHP

Problem 3: Lift Station Cycle Time

Question: A wet well has an operating volume of 3 , 000 gallons 3,000\text{ gallons} 3 , 000 gallons between the lead pump start float and stop float. If sewage enters at a constant rate of 150 gpm 150\text{ gpm} 150 gpm and the pump capacity is 450 gpm 450\text{ gpm} 450 gpm , calculate the total cycle time in minutes.

Step 1: Calculate fill time ( t fill t_{\text{fill}} t fill ​ ): t fill = 3 , 000 gal 150 gpm = 20.0 minutes t_{\text{fill}} = \frac{3,000\text{ gal}}{150\text{ gpm}} = 20.0\text{ minutes} t fill ​ = 150 gpm 3 , 000 gal ​ = 20.0 minutes

Step 2: Calculate pump drawdown time ( t pump t_{\text{pump}} t pump ​ ): t pump = 3 , 000 gal 450 gpm − 150 gpm = 3 , 000 gal 300 gpm = 10.0 minutes t_{\text{pump}} = \frac{3,000\text{ gal}}{450\text{ gpm} - 150\text{ gpm}} = \frac{3,000\text{ gal}}{300\text{ gpm}} = 10.0\text{ minutes} t pump ​ = 450 gpm − 150 gpm 3 , 000 gal ​ = 300 gpm 3 , 000 gal ​ = 10.0 minutes

Step 3: Calculate total cycle time ( T T T ): T = 20.0 min + 10.0 min = 30.0 minutes T = 20.0\text{ min} + 10.0\text{ min} = \mathbf{30.0\text{ minutes}} T = 20.0 min + 10.0 min = 30.0 minutes

Step 4: Check motor starts per hour: Starts per Hour = 60 min/hr 30.0 min/cycle = 2 starts/hour ( Well within safe 4 to 6 limit ) \text{Starts per Hour} = \frac{60\text{ min/hr}}{30.0\text{ min/cycle}} = \mathbf{2\text{ starts/hour}} \quad (\text{Well within safe 4 to 6 limit}) Starts per Hour = 30.0 min/cycle 60 min/hr ​ = 2 starts/hour ( Well within safe 4 to 6 limit )