Study guide
3.4 Sewer Testing Methods: Smoke, Dye & Acoustic
ABC Wastewater Collection Operator Class I Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Gravity Sewers, System Components & Materials
1.1 Gravity Sewer Principles & System Layout 1.2 Sewer Pipe Materials, Sizing & Joining Methods 1.3 Manholes, Drop Structures & Appurtenances 1.4 Gravity Sewer Hydraulics, Slope & Scour Velocity
2 Chapter 2: Lift Stations, Pumping Systems & Force Mains
2.1 Lift Station Design: Wet Well vs Dry Well Systems 2.2 Wastewater Pumps & Operating Principles 2.3 Level Controls, Pump Sequencing & SCADA Telemetry 2.4 Force Mains, Valves & Surge Protection 2.5 Lift Station Emergency Power, Maintenance & Operation
3 Chapter 3: Sewer Inspection, Testing & Cleaning
3.1 Hydraulic Jetting & High-Velocity Cleaning 3.2 Mechanical Rodding, Bucketing & Clearing Methods 3.3 Closed-Circuit Television (CCTV) Inspection & NASSCO PACP 3.4 Sewer Testing Methods: Smoke, Dye & Acoustic 3.5 Root, Grease & Debris Management
4 Chapter 4: Inflow & Infiltration (I/I), SSOs & FOG Management
4.1 Inflow vs Infiltration Fundamentals & RDII 4.2 Sanitary Sewer Overflows (SSOs) & Combined Sewer Overflows (CSOs) 4.3 SSO Emergency Response, Containment & NPDES Reporting 4.4 Fats, Oils, and Grease (FOG) Control Programs 4.5 Sewer System Rehabilitation & Trenchless Methods
5 Chapter 5: Safety, Confined Space Entry & Environmental Hazards
5.1 OSHA 1910.146 Permit-Required Confined Space Standards 5.2 Atmospheric Testing, Monitoring & Calibration Sequence 5.3 Ventilation, PPE & Emergency Rescue Equipment 5.4 Hydrogen Sulfide (H2S), Toxic Gases & Crown Corrosion 5.5 Trenching, Excavation & Traffic Safety (MUTCD & 811)
6 Chapter 6: Operator Math, Hydraulics & System Administration
6.1 Flow, Velocity & Cross-Sectional Area Calculations 6.2 Lift Station Hydraulics, Pumping Rate & Drawdown Math 6.3 Sewer Slope, Invert Elevations & Grade Calculations 6.4 Chemical Dosing, Feed Rate & Quantity Calculations 6.5 Regulatory Framework, Recordkeeping & System Mapping
7 Chapter 7: Equipment Operation, Tools & Preventive Maintenance
7.1 Gas Detectors, Flow Meters & Blowers: Operation and Calibration 7.2 Balling, Flushing, Poly Pigs & Cleaning-Method Selection 7.3 Heavy Equipment, Excavation & Hydro Excavation 7.4 Electrical Equipment: VFDs, Motor Control Centers & Low-Voltage Devices 7.5 Preventive Maintenance Programs, SOP/OEM Compliance & Support Tools
8 Chapter 8: System Restoration, Mapping & Emergency Operations
8.1 Manhole, Tap & Lateral Rehabilitation and Exfiltration Control 8.2 Appurtenance Inspection: Air Release Valves, Siphons, Regulators & Outfalls 8.3 Blueprints, GIS, Asset Management & System Mapping 8.4 Emergency Bypass Pumping & System Failure Response 8.5 New Pipe Installation Inspection & Acceptance Testing
9 Chapter 9: Monitoring, Safety Programs & System Administration
9.1 Flow Monitoring, Flow Meters & Sensor Calibration 9.2 Wastewater Characteristics & Abnormal Discharge Identification 9.3 Chemical Handling, Inventory, Feed Systems & Spill Response 9.4 Electrical Safety, Lockout/Tagout, Fire Safety & Occupational Health 9.5 Customer Service, Safety Programs, Operator Training & Regulatory Administration
3.4 Sewer Testing Methods: Smoke, Dye & Acoustic
Key Takeaways Explain This Topic AI
Smoke testing utilizes high-capacity engine blowers (1,500–4,000 CFM) and non-toxic, zinc-free smoke to rapidly locate sources of storm inflow, illegal connections, and uncapped cleanouts.
Mandatory 24- to 48-hour advance public notice and direct morning coordination with 911 dispatch, police, and fire departments are required prior to initiating smoke tests.
Fluorescent dye testing (using biodegradable Uranine or Rhodamine WT) confirms direct hydraulic cross-connections and estimates flow travel velocities.
Acoustic inspection technology (such as SL-RAT) transmits active sound pulses through pipe airspaces to screen 300-foot sewer segments for blockages in under three minutes.
Last updated: September 2026
Sewer Testing Methods: Smoke, Dye & Acoustic
Quick Answer: Non-destructive sewer testing methods evaluate system integrity and flow dynamics without full video profiling. Smoke testing isolates inflow sources (roof downspouts, catch basins, broken cleanouts); dye testing verifies direct hydraulic cross-connections; and acoustic testing (SL-RAT) uses sound wave attenuation to screen lines for blockages in minutes.
Collection system operators rely on specialized testing methods to detect illegal stormwater connections, locate groundwater infiltration, trace complex hydraulic paths, and assess blockage severity. Mastering the operational procedures, equipment setups, and regulatory requirements for smoke, dye, and acoustic testing is a high-yield area on the ABC Class I examination.
1. Smoke Testing Principles & Procedures
Smoke testing is an effective, economical method used to locate sources of inflow (surface stormwater entering sanitary sewers), illegal plumbing connections, vented sewer gas pathways, and cracked pipes near the ground surface. SMOKE TESTING SYSTEM SETUP & ESCAPE PATHS
- [Roof Downspout] [Plumbing Vent Stack]
- (Illegal Inflow) (Normal Release)
- || ||
- || (Smoke Exits!) || (Smoke Exits Properly)
- +---++---+ +---++---+
- | Building| | Building|
- +----+---+ +----+---+
- | | (Water Trap Intact)
- ===========|========================================|=================== (Ground Surface)
- | (Cleanout Cap Missing - Smoke Exits!) |
- | ^ |
- | | |
- (Sanitary | | |
- Lateral) +-----+ +------+
- \ /
- \ /
- [UPSTREAM MANHOLE] \ / [SETUP MANHOLE WITH BLOWER]
- +----------------+ \ / +-------------------------+
- | (Line Plugged) |====\=================================/====| [High-Capacity Blower] |
- +----------------+ ================================= | [Smoke Candle/Liquid] |
- +-------------------------+
- (Line Plugged Downstream)
- Equipment and Mechanics
High-Capacity Blower: Engine-driven blowers producing 1,500 to 4,000 CFM (cubic feet per minute) of airflow are seated over the open rim of the setup manhole using an air-seal canvas or rubber skirt.
Smoke Generation: Uses non-toxic, zinc-free pyrotechnic smoke candles (producing white/gray smoke for 3 to 5 minutes) or automated liquid aerosol smoke generators that inject mineral oil-based mist into the blower air stream.
Line Plugs: Expandable pneumatic plugs or sandbags are placed in the upstream and downstream pipes to isolate the test segment (typically 300 to 600 feet) and force smoke through defects.
Interpreting Smoke Observations
Observation Point Meaning / System Condition Action Required
Roof Plumbing Vent Stacks Normal condition; confirms smoke has filled the lateral and home trap is intact No action; log as verified connection
Roof Downspouts / Gutters Illegal Inflow; direct cross-connection to sanitary sewer Issue notice to property owner for disconnection
Open / Broken Yard Cleanout Inflow / Infiltration source; missing or damaged threaded cap Replace cleanout cap or repair riser
Street Catch Basin / Storm Drain Cross-Connection; cross-leakage between storm and sanitary main Emergency investigation and structural repair
Lawn / Soil Surface Broken lateral or shallow sanitary main crack venting to surface Schedule point excavation repair
Inside Building Living Space Dry plumbing P-trap, broken vent pipe, or defective toilet wax ring Advise occupant; ventilate building immediately
2. Public Notification & Safety Protocols for Smoke Testing
Smoke testing introduces artificial smoke into private plumbing fixtures, creating potential panic if safety protocols are ignored. +-------------------------------------------------------------------------+
- | MANDATORY SMOKE TESTING PROTOCOLS |
- +-------------------------------------------------------------------------+
- | 1. ADVANCE WRITTEN NOTICE: Deliver door-hanger notices to all affected |
- | residences 24 to 48 hours in advance. Explain test purpose and |
- | instruct residents to pour 1 gallon of water into all floor drains. |
- | 2. SPECIAL POPULATIONS: Identify and personally contact residents with |
- | respiratory conditions (asthma, COPD), elderly care homes, and schools|
- | 3. EMERGENCY DISPATCH: Notify local 911 dispatch, fire department, and |
- | police dispatch each morning before starting tests to prevent false |
- | structure fire alarms. |
- | 4. SAFETY DATA SHEETS: Keep zinc-free Smoke SDS on site at all times. |
- +-------------------------------------------------------------------------+
- 3. Fluorescent Dye Tracing
Dye testing introduces biodegradable, highly visible fluorescent dye into suspect fixtures, drains, or streams to trace flow paths and confirm hydraulic connectivity. +-------------------------------------------------------------------------+
- | COMMON TRACER DYES |
- +-----------------------+---------------------+---------------------------+
- | Dye Type | Visual Color | Primary Use Cases |
- +-----------------------+---------------------+---------------------------+
- | Sodium Fluorescein | Brilliant Yellow- | General cross-connections,|
- | (Uranine) | Green | sewer laterals, surface |
- | | | stormwater inflow |
- | Rhodamine WT | Vivid Red-Orange | Low-light monitoring, UV |
- | | / Fluorescent Pink | fluorometer quantification|
- +-----------------------+---------------------+---------------------------+
- Field Dye Testing Procedure
Deposit concentrated liquid or powdered dye (or dissolving dye tablets) into the fixture being evaluated (e.g., parking lot drain, building basement sump, or foundation footer).
Flush fixture with 50 to 500 gallons of potable water from a utility truck or fire hydrant to transport the dye through the lateral.
Station an operator at the downstream sanitary sewer manhole to visually monitor flow or place charcoal packets/optical fluorometers for automated detection.
Record travel time and confirmation of cross-connection.
4. Acoustic Inspection Technology (SL-RAT)
Acoustic assessment tools—such as the SL-RAT (Sewer Line Rapid Assessment Tool) —provide ultra-fast, non-destructive screening of collection lines to evaluate blockage levels without opening multiple cleanouts or launching CCTV crawlers. [MANHOLE A] [MANHOLE B]
- +--------------------+ +--------------------+
- | SL-RAT Transmitter | | SL-RAT Receiver |
- | (Acoustic Speaker) | | (Microphone Array) |
- +---------+----------+ +---------+----------+
- | |
- | Active Sound Pulses (Headspace) | Measured
- v v Attenuation
- =========================================================================
- | ))) ))) ))) [GREASE BLOCKAGE] ) ) |
- | Pipe Airspace (Dampens Sound) |
- |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
- | Wastewater Invert Flow ===========================================>> |
- =========================================================================
- Operating Principle
The Transmitter placed at Manhole A broadcasts a sequence of calibrated multi-frequency active sound pulses (audible and ultrasonic) through the pipe's internal headspace.
The Receiver placed at Manhole B captures the arriving sound signal and computes acoustic attenuation, dispersion, and phase changes.
Open, clean pipes transmit clear acoustic energy with minimal loss.
Blockages (roots, grease build-ups, heavy sediment, structural sags) scatter and absorb sound waves.
Assessment Scoring
Within under 3 minutes , the unit outputs a normalized score from 0 to 10 :
Score 7 to 10 (Good / Clean): No significant blockage; line does not require immediate cleaning.
Score 4 to 6 (Moderate Blockage): Partial obstruction or grease ring; schedule for routine maintenance.
Score 0 to 3 (Severe Blockage): Major blockage (>50% air loss) or structural collapse; dispatch emergency jetter immediately.
Operational Advantage: A two-person crew can screen 10,000 to 15,000 feet of sewer per day, allowing utilities to focus hydro-jetting equipment only on pipe segments that actually require cleaning.