Study guide

15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations

ABC/WPI Wastewater Treatment Operator Class I Certification Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Plant Overview & Preliminary Screening

1.1 Exam Structure, Plant Layout & Unit Process Flow 1.2 Bar Screens, Trash Racks & Mechanically Cleaned Screens 1.3 Comminutors, Macerators & Velocity-Controlled Grit Channels

2 Chapter 2: Grit Removal, Flow Equalization & Primary Clarification

2.1 Aerated Grit Chambers, Vortex Separators & Grit Handling 2.2 Primary Sedimentation Principles & Design Parameters 2.3 Primary Clarifier Operation, Sludge Pumping & Troubleshooting

3 Chapter 3: Secondary Biological Treatment — Activated Sludge Fundamentals

3.1 Activated Sludge Biochemistry & Aeration Tank Mechanics 3.2 Process Control Parameters: F/M Ratio, MCRT & Sludge Wasting 3.3 Settleability Testing, Sludge Volume Index & Clarifier Blanket Dynamics 3.4 Activated Sludge Troubleshooting & Microscopic Bioindicators

4 Chapter 4: Alternative Biological Processes & Fixed-Film Systems

4.1 Extended Aeration Package Plants, Oxidation Ditches & SBR Cycles 4.2 Fixed-Film Systems: Trickling Filters & Rotating Biological Contactors (RBCs) 4.3 Waste Stabilization Ponds, Facultative Lagoons & Aerated Ponds

5 Chapter 5: Disinfection Systems & Effluent Management

5.1 Chlorination Chemistry, Feed Equipment & Chlorine Contact Basins 5.2 Dechlorination Systems, Sulfur Dioxide & Bisulfite Chemistry 5.3 Ultraviolet (UV) Disinfection Mechanics, Dosage & Effluent Standards

6 Chapter 6: Solids Handling, Digestion & Biosolids Management

6.1 Sludge Thickening: Gravity, DAF & Gravity Belt Thickeners 6.2 Aerobic & Anaerobic Digestion Principles & Operational Control 6.3 Dewatering Technologies: Belt Filter Presses, Centrifuges & Drying Beds 6.4 Biosolids Regulations, EPA 40 CFR Part 503 & Land Application

7 Chapter 7: Sampling Protocols, Laboratory Testing & Operator Math

7.1 Wastewater Sampling Methods, Representative Samples & Chain of Custody 7.2 Biochemical Oxygen Demand (BOD5/CBOD5) & Total Suspended Solids (TSS) Analysis 7.3 Routine Process Testing: Dissolved Oxygen, pH, Settleable Solids & Ammonia 7.4 Essential Operator Math: Flow Conversions, Detention Time, Loading Rates & Pounds Formula

8 Chapter 8: Safety, Collection Systems, Utility Operations & Regulations

8.1 Confined Space Entry, Atmospheric Testing & Hazardous Gas Safety 8.2 Chemical Safety: Chlorine Gas Cylinders, Hypochlorite & Hazard Communication 8.3 Collection Systems, Lift Stations, Inflow/Infiltration & Clean Water Act / NPDES Compliance

9 Chapter 9: Pumps, Motors, Drives & Plant Electrical Systems

9.1 Centrifugal Pumps: Types, Curves, Cavitation & Seal Maintenance 9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic 9.3 Motors, Motor Control Centers, Variable Frequency Drives & Electrical Safety

10 Chapter 10: Aeration, Mixing & Chemical Feed Equipment

10.1 Aeration Equipment: Blowers, Diffusers, Surface Aerators & Air Distribution 10.2 Mixers, Flash Mixing & Chemical Feed Systems

11 Chapter 11: Instrumentation, Online Analyzers, SCADA & Auxiliary Power

11.1 Field Instrumentation: Flow Measurement, Level Sensing & Pressure 11.2 Online Process Analyzers: Dissolved Oxygen, pH, ORP, Turbidity & Chlorine Residual 11.3 SCADA, Telemetry, Alarm Management, Security & Auxiliary Power

12 Chapter 12: Valves, Piping, Compressors & Ancillary Plant Equipment

12.1 Valves, Piping, Air Compressors, Conveyors, Hoists & Cranes

13 Chapter 13: Tertiary Filtration & Effluent Polishing

13.1 Tertiary Filtration Equipment: Granular Media, Disc & Cloth Filters 13.2 Filtration Process Control: Loading Rates, Headloss, Breakthrough & Backwash Triggers

14 Chapter 14: Activated Sludge Configurations & Biological Nutrient Removal

14.1 Activated Sludge Configurations: Conventional Plug Flow, Complete Mix, Step Feed & Contact Stabilization 14.2 Nutrient Removal: Nitrification, Denitrification & Anaerobic/Anoxic/Aerobic Zones

15 Chapter 15: Chemical Dosing Processes, Effluent Disposal & Solids Disposal

15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations 15.2 Effluent Disposal: Surface Water Discharge & Rapid Infiltration Basins; Solids Disposal to Landfill

16 Chapter 16: Bacteriological Analyses, Chemical Analyses & Laboratory Quality Control

16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting 16.2 Chemical Analyses & Laboratory Quality Control: COD, Nutrients, Metals, WET Testing & SOPs

17 Chapter 17: Safety Programs, Emergency Response, Security & Administrative Procedures

17.1 Lockout/Tagout, Machine Guarding, Fall Protection & PPE Programs 17.2 Emergency Response, Spill Control, Security & Vulnerability Assessments 17.3 Administrative Procedures: SOPs, O&M Reports, Discharge Monitoring Reports & Recordkeeping

15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations

Key Takeaways Explain This Topic AI

Chemical feed rate in pounds per day equals flow in MGD multiplied by dose in mg/L multiplied by 8.34 pounds per gallon, and this single relationship covers nearly every dosing calculation on the exam.

When a chemical is supplied as a solution or at less than 100 percent purity, the calculated pounds of active chemical must be divided by the decimal purity or solution strength to find the pounds of product actually required.

Coagulation destabilizes charged colloidal particles in seconds with rapid mixing, while flocculation grows the destabilized particles into settleable floc over many minutes with gentle tapered mixing.

Alum and ferric salts consume alkalinity and depress pH, so a plant that both nitrifies and doses metal salts must manage a single shared alkalinity budget.

Jar testing is the standard method for selecting a coagulant dose because the optimum dose depends on the actual water and cannot be read from a table.

Last updated: September 2026

15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations

Exam Focus: "Chemical dosing — Coagulation/flocculation, Nutrient removal/enhancement, pH adjustment" is a Treatment Process line item, and Treatment Process carries nine of the exam's ten calculation items . Dosage math is very likely to appear.

1. The Dosage Calculation

Every chemical feed calculation rests on one relationship: Pounds per day = Flow (MGD) x Dose (mg/L) x 8.34 lb/gal

The 8.34 is the weight of one gallon of water in pounds, and it is what converts a concentration and a volume into a mass.

Worked Example 1 — Straightforward Dose

A plant treating 3.2 MGD doses ferric chloride at 18 mg/L . How many pounds per day of ferric chloride are required? lb/day = 3.2 MGD x 18 mg/L x 8.34 = 480.4 lb/day

Worked Example 2 — Correcting for Solution Strength

The same plant buys ferric chloride as a 38 percent solution . The 480.4 lb/day above is the active chemical required; the plant must feed more product than that because the product is only 38 percent active. lb/day of product = 480.4 / 0.38 = 1,264 lb/day of 38% solution

The rule: divide by the decimal purity or strength. Dividing by a number less than one always increases the answer, which is the sanity check — you always need more product than active chemical. Candidates who multiply by 0.38 instead get a number smaller than the active requirement, which is physically impossible.

Worked Example 3 — Working Backward to a Dose

A plant feeds 210 lb/day of a chemical at 100 percent strength while treating 1.5 MGD . What is the dose? Dose (mg/L) = lb/day / (MGD x 8.34) = 210 / (1.5 x 8.34) = 210 / 12.51 = 16.8 mg/L

2. Coagulation and Flocculation

Fine colloidal particles do not settle because they carry like electrical charges and repel one another, keeping the suspension stable. Removing them requires two distinct steps.

Coagulation adds a coagulant — typically alum (aluminum sulfate) or a ferric salt (ferric chloride, ferric sulfate) — whose multivalent metal ions neutralize the particle charge. Once charge is neutralized the particles no longer repel and can stick together on contact. Coagulation is a chemical step that happens in seconds and requires intense rapid mixing to disperse the coagulant before it hydrolyzes.

Flocculation is the physical step that follows: gentle mixing over 20 to 30 minutes brings destabilized particles into contact so they aggregate into large, dense, settleable floc. As covered in Section 10.2, too much mixing energy in the flocculator shears the floc apart , and sheared floc does not re-form.

A flocculant aid polymer may be added after coagulation to bridge particles together and strengthen the floc.

Where Coagulation Is Used in a Wastewater Plant

Chemical phosphorus precipitation — the most common application at a municipal plant.

Chemically enhanced primary treatment to boost primary clarifier removal during wet weather.

Improving solids capture ahead of tertiary filters.

Sludge conditioning ahead of dewatering (usually a polymer rather than a metal salt).

Jar Testing

The correct coagulant dose depends on the actual characteristics of the water on that day, so it is determined empirically. A jar test runs several beakers of the same water side by side at different doses through a simulated rapid mix, flocculation, and settling sequence, and the operator compares floc formation, settling rate, and supernatant clarity. Jar testing is the standard method for selecting and adjusting coagulant dose, and it must be repeated when water characteristics change.

3. pH and Alkalinity Adjustment

Alkalinity is the water's capacity to neutralize acid — its buffer against pH change. pH is the current hydrogen ion condition. A water can sit at a comfortable pH and still have almost no alkalinity, and that water will crash the moment any acid-producing process starts.

To Raise pH / Add Alkalinity Notes

Sodium hydroxide (caustic soda) Fast-acting liquid, easy to feed, no slurry handling; expensive and a severe burn hazard; freezes at moderate temperature at high concentration

Lime (calcium hydroxide) Inexpensive per pound of alkalinity; requires slurry make-up, continuous agitation, and abrasion-resistant equipment; scales piping

  • Soda ash (sodium carbonate) Easy to handle as a dry chemical; costlier than lime
  • Magnesium hydroxide Safer to handle, self-limiting on pH, slower acting
  • To Lower pH Notes
  • Carbon dioxide Self-limiting and safer; forms carbonic acid
  • Sulfuric acid Fast and inexpensive; severe hazard, requires dedicated containment and PPE
  • The Alkalinity Budget

Several processes draw on the same alkalinity reserve simultaneously:

Nitrification consumes about 7.14 lb as CaCO3 per lb of ammonia nitrogen oxidized (Section 14.2).

Metal salt coagulants — alum and ferric — also consume alkalinity and depress pH.

Denitrification returns about 3.57 lb as CaCO3 per lb of nitrate nitrogen reduced.

A plant that nitrifies and doses ferric for phosphorus removal is drawing on that reserve twice. Monitoring effluent alkalinity as a routine process control test — and holding a residual, commonly targeted at 50 to 100 mg/L as CaCO3 — is what keeps both processes stable.

4. Practical Dosing Discipline

Change one variable at a time , and give the process time to respond before judging the result.

Verify actual feed rate against a calibration cylinder or a tank draw-down, not the pump dial (Section 9.2).

Track chemical usage per million gallons treated — a sudden change in usage at a stable dose means a feed system problem.

Watch for over-dosing. Excess coagulant can re-stabilize particles by reversing their charge, producing worse clarity at a higher dose. This is one of the main things a jar test reveals.

Respect the safety data sheet for every chemical, and never mix incompatible chemicals or store them where a spill could combine them (Section 10.2).