Study guide

16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting

ABC/WPI Wastewater Treatment Operator Class I Certification Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Plant Overview & Preliminary Screening

1.1 Exam Structure, Plant Layout & Unit Process Flow 1.2 Bar Screens, Trash Racks & Mechanically Cleaned Screens 1.3 Comminutors, Macerators & Velocity-Controlled Grit Channels

2 Chapter 2: Grit Removal, Flow Equalization & Primary Clarification

2.1 Aerated Grit Chambers, Vortex Separators & Grit Handling 2.2 Primary Sedimentation Principles & Design Parameters 2.3 Primary Clarifier Operation, Sludge Pumping & Troubleshooting

3 Chapter 3: Secondary Biological Treatment — Activated Sludge Fundamentals

3.1 Activated Sludge Biochemistry & Aeration Tank Mechanics 3.2 Process Control Parameters: F/M Ratio, MCRT & Sludge Wasting 3.3 Settleability Testing, Sludge Volume Index & Clarifier Blanket Dynamics 3.4 Activated Sludge Troubleshooting & Microscopic Bioindicators

4 Chapter 4: Alternative Biological Processes & Fixed-Film Systems

4.1 Extended Aeration Package Plants, Oxidation Ditches & SBR Cycles 4.2 Fixed-Film Systems: Trickling Filters & Rotating Biological Contactors (RBCs) 4.3 Waste Stabilization Ponds, Facultative Lagoons & Aerated Ponds

5 Chapter 5: Disinfection Systems & Effluent Management

5.1 Chlorination Chemistry, Feed Equipment & Chlorine Contact Basins 5.2 Dechlorination Systems, Sulfur Dioxide & Bisulfite Chemistry 5.3 Ultraviolet (UV) Disinfection Mechanics, Dosage & Effluent Standards

6 Chapter 6: Solids Handling, Digestion & Biosolids Management

6.1 Sludge Thickening: Gravity, DAF & Gravity Belt Thickeners 6.2 Aerobic & Anaerobic Digestion Principles & Operational Control 6.3 Dewatering Technologies: Belt Filter Presses, Centrifuges & Drying Beds 6.4 Biosolids Regulations, EPA 40 CFR Part 503 & Land Application

7 Chapter 7: Sampling Protocols, Laboratory Testing & Operator Math

7.1 Wastewater Sampling Methods, Representative Samples & Chain of Custody 7.2 Biochemical Oxygen Demand (BOD5/CBOD5) & Total Suspended Solids (TSS) Analysis 7.3 Routine Process Testing: Dissolved Oxygen, pH, Settleable Solids & Ammonia 7.4 Essential Operator Math: Flow Conversions, Detention Time, Loading Rates & Pounds Formula

8 Chapter 8: Safety, Collection Systems, Utility Operations & Regulations

8.1 Confined Space Entry, Atmospheric Testing & Hazardous Gas Safety 8.2 Chemical Safety: Chlorine Gas Cylinders, Hypochlorite & Hazard Communication 8.3 Collection Systems, Lift Stations, Inflow/Infiltration & Clean Water Act / NPDES Compliance

9 Chapter 9: Pumps, Motors, Drives & Plant Electrical Systems

9.1 Centrifugal Pumps: Types, Curves, Cavitation & Seal Maintenance 9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic 9.3 Motors, Motor Control Centers, Variable Frequency Drives & Electrical Safety

10 Chapter 10: Aeration, Mixing & Chemical Feed Equipment

10.1 Aeration Equipment: Blowers, Diffusers, Surface Aerators & Air Distribution 10.2 Mixers, Flash Mixing & Chemical Feed Systems

11 Chapter 11: Instrumentation, Online Analyzers, SCADA & Auxiliary Power

11.1 Field Instrumentation: Flow Measurement, Level Sensing & Pressure 11.2 Online Process Analyzers: Dissolved Oxygen, pH, ORP, Turbidity & Chlorine Residual 11.3 SCADA, Telemetry, Alarm Management, Security & Auxiliary Power

12 Chapter 12: Valves, Piping, Compressors & Ancillary Plant Equipment

12.1 Valves, Piping, Air Compressors, Conveyors, Hoists & Cranes

13 Chapter 13: Tertiary Filtration & Effluent Polishing

13.1 Tertiary Filtration Equipment: Granular Media, Disc & Cloth Filters 13.2 Filtration Process Control: Loading Rates, Headloss, Breakthrough & Backwash Triggers

14 Chapter 14: Activated Sludge Configurations & Biological Nutrient Removal

14.1 Activated Sludge Configurations: Conventional Plug Flow, Complete Mix, Step Feed & Contact Stabilization 14.2 Nutrient Removal: Nitrification, Denitrification & Anaerobic/Anoxic/Aerobic Zones

15 Chapter 15: Chemical Dosing Processes, Effluent Disposal & Solids Disposal

15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations 15.2 Effluent Disposal: Surface Water Discharge & Rapid Infiltration Basins; Solids Disposal to Landfill

16 Chapter 16: Bacteriological Analyses, Chemical Analyses & Laboratory Quality Control

16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting 16.2 Chemical Analyses & Laboratory Quality Control: COD, Nutrients, Metals, WET Testing & SOPs

17 Chapter 17: Safety Programs, Emergency Response, Security & Administrative Procedures

17.1 Lockout/Tagout, Machine Guarding, Fall Protection & PPE Programs 17.2 Emergency Response, Spill Control, Security & Vulnerability Assessments 17.3 Administrative Procedures: SOPs, O&M Reports, Discharge Monitoring Reports & Recordkeeping

16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting

Key Takeaways Explain This Topic AI

Bacteriological limits are written for indicator organisms such as fecal coliform or E. coli rather than for pathogens directly, because indicators are inexpensive and reliable to measure and their presence signals fecal contamination.

In the membrane filtration method a measured sample volume is drawn through a 0.45 micron membrane, the membrane is incubated on a selective medium, and colonies are counted, with fecal coliform incubated at 44.5 degrees C plus or minus 0.2 degrees C.

Membrane filtration results are calculated as colonies counted multiplied by 100 and divided by the milliliters of sample filtered, giving a result in colonies per 100 mL, and the count is only statistically valid within the method’s ideal counting range.

Bacteriological sample bottles must be sterile and must contain sodium thiosulfate to neutralize any chlorine residual, because residual chlorine continues killing organisms in the bottle and produces a falsely low result.

Bacteriological permit limits are almost always expressed as a geometric mean rather than an arithmetic average, because bacterial counts span orders of magnitude and a single high value would otherwise dominate the reported result.

Last updated: September 2026

16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting

Exam Focus: "Collect samples for bacteriological analyses," "Conduct bacteriological analyses," and "Interpret data from bacteriological analyses" are three separate lines in the Laboratory Analysis content area. Disinfection performance is judged entirely by this test.

1. Why Indicator Organisms

Testing directly for every pathogen that might be present in wastewater — Salmonella , Shigella , hepatitis A, Giardia , Cryptosporidium — would be slow, expensive, and unreliable, because pathogens are present intermittently and in low numbers even when the risk is real.

Instead, regulators use indicator organisms : bacteria that are abundant in the intestines of warm-blooded animals, easy and cheap to culture, and present in far greater numbers than pathogens. Finding them means fecal contamination is present; not finding them means disinfection is working.

Indicator What It Indicates Typical Use

Total coliform Broad group including environmental organisms; not specific to fecal contamination Drinking water; less useful in wastewater

Fecal coliform The thermotolerant subset that grows at elevated temperature; strongly associated with fecal contamination The traditional and still very common wastewater permit parameter

E. coli A specific member of the fecal coliform group; the most direct indicator of fecal contamination Increasingly the parameter of choice for freshwater discharges

  • Enterococci Survives better in saline water Marine and estuarine discharges
  • 2. Membrane Filtration

The membrane filtration (MF) method is the workhorse of the wastewater laboratory.

Sterilize the filtration apparatus and use aseptic technique throughout.

Filter a measured volume of sample through a sterile 0.45 micron membrane filter. Bacteria are retained on the surface of the membrane; water passes through.

Transfer the membrane to a pad or plate saturated with a selective growth medium.

Incubate at the temperature and for the time the method specifies. For fecal coliform this is 44.5 degrees C plus or minus 0.2 degrees C , a tight tolerance that requires a properly calibrated and monitored incubator or water bath.

Count the characteristic colonies — for fecal coliform on mFC medium, the blue colonies.

The Calculation Colonies per 100 mL = (Number of colonies counted x 100) / mL of sample filtered

Worked example. An analyst filters 25 mL of final effluent and counts 32 blue colonies. (32 x 100) / 25 = 3,200 / 25 = 128 colonies per 100 mL

Valid Counting Range

A count is only statistically meaningful within the method's ideal counting range — for fecal coliform by membrane filtration this is conventionally 20 to 60 colonies per membrane.

Too few colonies and the count is dominated by random variation.

Too many colonies and they crowd, merge, and compete for nutrients, so the count under-reports.

Because the number of colonies depends on how much sample you filter, and effluent quality varies, filter several different volumes (a dilution series) on every sample so at least one plate lands in the ideal range.

A plate with excessive growth is reported as TNTC (too numerous to count) and is not used to calculate a result.

3. Other Approved Approaches

Multiple tube fermentation (MTF) inoculates a series of tubes at several dilutions and reports a statistical Most Probable Number (MPN) based on the pattern of positive tubes. Slower and more labor-intensive, but it works on turbid samples that would clog a membrane.

Enzyme substrate (defined substrate) methods use a medium containing substrates that specific enzymes in coliforms and E. coli cleave, producing a color change or fluorescence. Results are reported as MPN. These methods are simple and widely used, but the reagent lot and incubation conditions must follow the manufacturer's instructions exactly.

Approved methods only. Compliance results must come from a method approved for the parameter under 40 CFR Part 136. A method that is convenient but unapproved produces a number you cannot report.

4. Sampling and Handling — Where Results Get Ruined

  • Requirement Reason for It
  • Sterile bottle Any organism already in the bottle is counted as though it came from the effluent

Sodium thiosulfate in the bottle Neutralizes chlorine residual. Without it, residual chlorine keeps killing organisms during transport and the reported count is falsely low — the plant looks like it is disinfecting better than it is

Do not rinse the bottle Rinsing washes out the thiosulfate

Do not touch the bottle lip or the inside of the cap Contamination from hands is the most common laboratory error in this test

Fill without overflowing; leave headspace Air space is needed to mix the sample before analysis

Ice immediately and keep cold Bacteria multiply or die off at ambient temperature, changing the result in either direction

Analyze promptly Holding time is short — bacteriological samples must be processed as quickly as practical, within the holding time the approved method and the permit specify

Grab sample only Bacteriological samples are never composited , because organisms would grow or die during the compositing period

Sample at the permitted monitoring point Usually after disinfection and, where dechlorination is practiced, at the location the permit designates

5. Geometric Mean Reporting

Bacterial counts range over orders of magnitude, so an arithmetic average is dominated by a single high value. Permits therefore express bacteriological limits as a geometric mean .

Method A — the root of the product. Multiply the n results together and take the n th root.

Method B — logarithms (easier with a calculator). Take the base-10 logarithm of each result, average the logarithms, and take the antilogarithm of that average.

Worked example. Seven weekly fecal coliform results: 10, 40, 100, 200, 800, 1,000, and 5,000 colonies per 100 mL.

Arithmetic mean = (10 + 40 + 100 + 200 + 800 + 1,000 + 5,000) / 7 = 7,150 / 7 = 1,021 per 100 mL — a value larger than five of the seven results, pulled up almost entirely by the single 5,000.

Geometric mean: logs are 1.000, 1.602, 2.000, 2.301, 2.903, 3.000, and 3.699. Their sum is 16.505 and the average is 2.358. The antilog of 2.358 is approximately 228 per 100 mL .

The geometric mean of 228 represents the central tendency of that data set far better than 1,021 does, which is exactly why permits use it.

Practical points. A result reported as zero cannot be used directly in a logarithm, so approved conventions substitute a value such as 1 for a non-detect. And because the geometric mean is resistant to a single high value, a single excursion rarely violates a geometric mean limit by itself — but permits usually pair the geometric mean limit with a separate maximum single-sample limit that a single excursion violates immediately.