Study guide
9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic
ABC/WPI Wastewater Treatment Operator Class I Certification Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Plant Overview & Preliminary Screening
1.1 Exam Structure, Plant Layout & Unit Process Flow 1.2 Bar Screens, Trash Racks & Mechanically Cleaned Screens 1.3 Comminutors, Macerators & Velocity-Controlled Grit Channels
2 Chapter 2: Grit Removal, Flow Equalization & Primary Clarification
2.1 Aerated Grit Chambers, Vortex Separators & Grit Handling 2.2 Primary Sedimentation Principles & Design Parameters 2.3 Primary Clarifier Operation, Sludge Pumping & Troubleshooting
3 Chapter 3: Secondary Biological Treatment — Activated Sludge Fundamentals
3.1 Activated Sludge Biochemistry & Aeration Tank Mechanics 3.2 Process Control Parameters: F/M Ratio, MCRT & Sludge Wasting 3.3 Settleability Testing, Sludge Volume Index & Clarifier Blanket Dynamics 3.4 Activated Sludge Troubleshooting & Microscopic Bioindicators
4 Chapter 4: Alternative Biological Processes & Fixed-Film Systems
4.1 Extended Aeration Package Plants, Oxidation Ditches & SBR Cycles 4.2 Fixed-Film Systems: Trickling Filters & Rotating Biological Contactors (RBCs) 4.3 Waste Stabilization Ponds, Facultative Lagoons & Aerated Ponds
5 Chapter 5: Disinfection Systems & Effluent Management
5.1 Chlorination Chemistry, Feed Equipment & Chlorine Contact Basins 5.2 Dechlorination Systems, Sulfur Dioxide & Bisulfite Chemistry 5.3 Ultraviolet (UV) Disinfection Mechanics, Dosage & Effluent Standards
6 Chapter 6: Solids Handling, Digestion & Biosolids Management
6.1 Sludge Thickening: Gravity, DAF & Gravity Belt Thickeners 6.2 Aerobic & Anaerobic Digestion Principles & Operational Control 6.3 Dewatering Technologies: Belt Filter Presses, Centrifuges & Drying Beds 6.4 Biosolids Regulations, EPA 40 CFR Part 503 & Land Application
7 Chapter 7: Sampling Protocols, Laboratory Testing & Operator Math
7.1 Wastewater Sampling Methods, Representative Samples & Chain of Custody 7.2 Biochemical Oxygen Demand (BOD5/CBOD5) & Total Suspended Solids (TSS) Analysis 7.3 Routine Process Testing: Dissolved Oxygen, pH, Settleable Solids & Ammonia 7.4 Essential Operator Math: Flow Conversions, Detention Time, Loading Rates & Pounds Formula
8 Chapter 8: Safety, Collection Systems, Utility Operations & Regulations
8.1 Confined Space Entry, Atmospheric Testing & Hazardous Gas Safety 8.2 Chemical Safety: Chlorine Gas Cylinders, Hypochlorite & Hazard Communication 8.3 Collection Systems, Lift Stations, Inflow/Infiltration & Clean Water Act / NPDES Compliance
9 Chapter 9: Pumps, Motors, Drives & Plant Electrical Systems
9.1 Centrifugal Pumps: Types, Curves, Cavitation & Seal Maintenance 9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic 9.3 Motors, Motor Control Centers, Variable Frequency Drives & Electrical Safety
10 Chapter 10: Aeration, Mixing & Chemical Feed Equipment
10.1 Aeration Equipment: Blowers, Diffusers, Surface Aerators & Air Distribution 10.2 Mixers, Flash Mixing & Chemical Feed Systems
11 Chapter 11: Instrumentation, Online Analyzers, SCADA & Auxiliary Power
11.1 Field Instrumentation: Flow Measurement, Level Sensing & Pressure 11.2 Online Process Analyzers: Dissolved Oxygen, pH, ORP, Turbidity & Chlorine Residual 11.3 SCADA, Telemetry, Alarm Management, Security & Auxiliary Power
12 Chapter 12: Valves, Piping, Compressors & Ancillary Plant Equipment
12.1 Valves, Piping, Air Compressors, Conveyors, Hoists & Cranes
13 Chapter 13: Tertiary Filtration & Effluent Polishing
13.1 Tertiary Filtration Equipment: Granular Media, Disc & Cloth Filters 13.2 Filtration Process Control: Loading Rates, Headloss, Breakthrough & Backwash Triggers
14 Chapter 14: Activated Sludge Configurations & Biological Nutrient Removal
14.1 Activated Sludge Configurations: Conventional Plug Flow, Complete Mix, Step Feed & Contact Stabilization 14.2 Nutrient Removal: Nitrification, Denitrification & Anaerobic/Anoxic/Aerobic Zones
15 Chapter 15: Chemical Dosing Processes, Effluent Disposal & Solids Disposal
15.1 Chemical Dosing Processes: Coagulation, Flocculation, pH Adjustment & Dosage Calculations 15.2 Effluent Disposal: Surface Water Discharge & Rapid Infiltration Basins; Solids Disposal to Landfill
16 Chapter 16: Bacteriological Analyses, Chemical Analyses & Laboratory Quality Control
16.1 Bacteriological Analyses: Indicator Organisms, Membrane Filtration & Geometric Mean Reporting 16.2 Chemical Analyses & Laboratory Quality Control: COD, Nutrients, Metals, WET Testing & SOPs
17 Chapter 17: Safety Programs, Emergency Response, Security & Administrative Procedures
17.1 Lockout/Tagout, Machine Guarding, Fall Protection & PPE Programs 17.2 Emergency Response, Spill Control, Security & Vulnerability Assessments 17.3 Administrative Procedures: SOPs, O&M Reports, Discharge Monitoring Reports & Recordkeeping
9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic
Key Takeaways Explain This Topic AI
A positive displacement pump traps a fixed volume of liquid per revolution or stroke and delivers nearly the same flow regardless of discharge head, which makes it the correct choice for thick sludge and for accurate chemical metering.
Every positive displacement pump discharge line must have a pressure relief valve, because operating the pump against a closed valve will rupture piping, split the casing, or shear the shaft within seconds.
A progressive cavity pump must never be run dry: the elastomer stator relies on pumped liquid for lubrication and cooling, and a dry run of even a minute or two burns the stator.
Peristaltic (hose) pumps have no seals, valves, or wetted rotating parts because the liquid contacts only the inside of the hose, making them ideal for polymer and lime slurry — the hose is the scheduled wear item.
Diaphragm metering pumps set feed rate by stroke length and stroke frequency, and their actual output must be verified against a calibration cylinder rather than trusted from the dial setting.
Last updated: September 2026
9.2 Positive Displacement Pumps: Progressive Cavity, Plunger, Diaphragm & Peristaltic
Exam Focus: The Need-to-Know Criteria lists positive displacement, peristaltic, and diaphragm pumps by name alongside centrifugal pumps. The most heavily tested single concept is the consequence of closing a valve downstream of a positive displacement pump.
1. The Fixed-Volume Principle
A positive displacement (PD) pump captures a discrete volume of liquid in a cavity, moves it mechanically from suction to discharge, and expels it. Displacement is set by geometry, so:
Flow is essentially constant regardless of discharge head. Raise the head and the pump simply works harder at the same flow — until something breaks.
The pump is self-priming and will pull a suction lift , because it can evacuate air from the suction line.
The pump will generate whatever pressure it takes to move that volume. This is the dangerous property.
The Rule That Gets Tested
A positive displacement pump must never be started or operated against a closed discharge valve. With nowhere for the trapped volume to go, pressure climbs almost instantly to the point of failure: burst piping, a split casing, a sheared shaft, or a stalled and burned-out motor. Every PD pump discharge must therefore be protected by a pressure relief valve piped back to the suction or to the wet well.
A centrifugal pump under the same conditions merely churns and slowly overheats. This contrast — centrifugal tolerates dead-heading briefly, positive displacement does not — is the single most reliable exam discriminator between the two families.
2. The Positive Displacement Family in a Wastewater Plant
Pump Type Typical Service Operating Notes and Failure Modes
Progressive cavity (PC) Primary sludge, thickened WAS, digested sludge, polymer A single-helix steel rotor turns inside a double-helix elastomer stator. Smooth, non-pulsating flow, handles high solids and viscosity. Never run dry — the pumped liquid is the only lubricant and coolant for the stator, which burns in minutes. Wear shows up as falling capacity at the same speed.
Plunger / piston Older primary and digested sludge service Very high pressure capability, tolerates grit and rags. Produces strongly pulsating flow, so a pulsation dampener or air chamber is normally fitted. Ball checks foul with rags.
Rotary lobe Sludge transfer, digester recirculation, RAS Two counter-rotating lobes that never touch each other. Compact, reversible (useful for clearing a blockage), and easy to service in place. Lobe clearance opens with abrasive wear.
Air-operated double diaphragm (AODD) Sump service, grit, chemical transfer, portable duty Compressed air alternately flexes two diaphragms. Can be dead-headed and stalled safely, runs dry without damage, and is completely self-priming — the exceptions that prove the rule. Icing of the air valve is the common complaint.
Diaphragm metering Chemical feed: hypochlorite, bisulfite, polymer, alkalinity chemicals A motor-driven diaphragm displaces a precise volume per stroke. Output is set by stroke length and stroke frequency . Vapor lock ("gas binding") from off-gassing hypochlorite is the classic fault.
Peristaltic (hose/tube) Polymer, lime slurry, abrasive or shear-sensitive chemicals A roller or shoe squeezes a flexible hose. The liquid touches only the inside of the hose — no seals, valves, or rotating wetted parts to fail. The hose is a scheduled consumable. Excellent for abrasives that would destroy any other pump.
Screw (Archimedes) pump Influent lifting, RAS return An inclined helical screw in a trough. Strictly a lifting device against a low fixed head. Self-limiting on flow, passes rags without clogging, and cannot be dead-headed because there is no closed discharge.
3. Chemical Metering Pump Calibration
Chemical dosing equipment is named separately in the Need-to-Know Criteria, and metering pumps are the equipment behind it. Do not trust the dial. Diaphragm check valves wear, back pressure changes, and a pump that reads 60% on the stroke dial may deliver considerably less.
Verify output with a calibration cylinder (draw-down column):
Switch the metering pump suction from the day tank to the calibration cylinder and fill the cylinder.
Record the starting liquid level and start a stopwatch.
Run the pump for a measured interval — typically 5 to 10 minutes at normal settings.
Record the volume drawn down and divide by elapsed time to get true output in mL/min or gallons per hour.
Compare to the intended feed rate and adjust stroke length or frequency, then re-verify.
Practical points that appear as exam distractors:
Adjust stroke length for coarse capacity changes and stroke frequency for fine trimming; manufacturers generally recommend keeping stroke length above roughly 20% for repeatable accuracy.
Install a back-pressure valve when discharging into a low-pressure line, or the pump will siphon and overfeed.
Sodium hypochlorite off-gasses, so metering pumps on hypochlorite need a degassing or self-venting head and a flooded suction.
A calibration cylinder is a verification device, not a feed tank — return the suction to the day tank when finished.
4. Selecting Between Centrifugal and Positive Displacement
- Consideration Centrifugal Positive Displacement
- Flow versus head Flow falls as head rises Flow nearly constant as head rises
- Closed discharge valve Churns; overheats over minutes Catastrophic overpressure in seconds
- Relief valve required No Yes, always
- Self-priming / suction lift Generally no (unless submersible or self-priming design) Yes
- High-viscosity sludge Performance collapses Handles readily
- Metering accuracy Poor Excellent
Typical wastewater duty Influent, RAS, WAS, effluent, plant water Primary and digested sludge, polymer, chemical feed