Study guide
5.1 Centrifugal, Positive-Displacement, Peristaltic & Diaphragm Pumps
ABC Wastewater Treatment Operator Class III Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Current Exam Identity, Blueprint & Calculation Strategy
Current WPI Class III Exam Blueprint, Calculations & Jurisdiction Check
2 Chapter 2: Preliminary & Primary Treatment Equipment
2.1 Screening, Grinding, Bar Screens & Grit-Removal Equipment 2.2 Flow Equalization Systems & Microscreens 2.3 Primary Clarifier & Sedimentation-Basin Equipment
3 Chapter 3: Secondary, Tertiary & Disinfection Equipment
3.1 Aeration Basins, Blowers, Surface Aerators & Diffusers 3.2 Media Filters, Membrane Filters & Tertiary Microscreens 3.3 Chlorination & Dechlorination Feed Equipment 3.4 Ultraviolet Disinfection Equipment
4 Chapter 4: Solids Treatment & Odor-Control Equipment
4.1 Belt Presses, Centrifuges, DAF & Gravity Thickeners 4.2 Aerobic & Anaerobic Digester Equipment 4.3 Odor-Control Biofilters & Scrubbers
5 Chapter 5: Pumps, Controls, Power & Ancillary Equipment
5.1 Centrifugal, Positive-Displacement, Peristaltic & Diaphragm Pumps 5.2 Mixers, Chemical Dosing, Motors & Motor Control Centers 5.3 Field Instruments, Online Analyzers, SCADA & Telemetry 5.4 Generators, Compressors, Conveyors, Valves, Hoists, Pipes & Fittings
6 Chapter 6: Preliminary & Primary Process Evaluation
6.1 Preliminary Processes: Screening, Grinding, Grit & Equalization 6.2 Primary Clarification & Sedimentation Process Control
7 Chapter 7: Suspended-Growth & Nutrient-Removal Processes
7.1 Complete-Mix Suspended-Growth Process 7.2 Extended Aeration & Oxidation-Ditch Control 7.3 Anaerobic–Anoxic–Aerobic Nutrient-Removal Processes 7.4 Conventional Activated Sludge, RAS/WAS & Final Clarifiers
8 Chapter 8: Tertiary Filtration & Disinfection Processes
8.1 Tertiary Filtration Process Evaluation 8.2 Chlorination Process Control, Demand, Residual & Contact 8.3 Dechlorination Process Evaluation & Adjustment 8.4 UV Disinfection Process Evaluation & Adjustment
9 Chapter 9: Solids Treatment & Disposal Processes
9.1 Aerobic Digestion Process Control 9.2 Anaerobic Digestion With & Without Cogeneration 9.3 Solids Thickening & Dewatering Process Adjustment 9.4 Land Application & Landfill Disposal of Solids
10 Chapter 10: Effluent Disposal & Chemical Process Adjustment
10.1 Surface-Water Discharge, Permit Limits & Process Response 10.2 Coagulation & Flocculation for Solids/Phosphorus Removal 10.3 Chemical Nutrient Enhancement & Odor Control 10.4 pH Adjustment & Chemical Feed Control
11 Chapter 11: Laboratory Quality Systems & Sample Collection
11.1 Laboratory SOPs, QA/QC & Defensible Records 11.2 Collecting Bacteriological, Biological, Chemical & Physical Samples
12 Chapter 12: Bacteriological & Biological Analysis
12.1 Bacteriological Analysis & Colony Calculations 12.2 BOD, CBOD & Whole-Effluent Toxicity Analysis
13 Chapter 13: Chemical, Physical & Integrated Data Analysis
13.1 COD, Nutrient & Metals Analysis 13.2 pH, Temperature, DO & Settleable-Solids Analysis 13.3 Process-Control vs Regulatory Testing, Data Interpretation & Instrument Care
14 Chapter 14: Safety Programs, SOPs & Energy Control
14.1 Safety Program, Stop-Work Judgment & SOP Adherence 14.2 Lockout/Tagout & Permit-Required Confined-Space Entry
15 Chapter 15: Chemical, Emergency & Security Procedures
15.1 Hazard Communication, Fall Protection, Chemical Handling & Emergency Response 15.2 Vulnerability Assessments & Routine Security Checks
16 Chapter 16: Safety Equipment, Selection & Administration
16.1 Maintaining Gas Detectors, Eyewashes, Showers & Respirators 16.2 Assisting With Wastewater Equipment Selection 16.3 O&M Reports, Regulatory Reports, Compliance, Customer Response & SOP Updates
5.1 Centrifugal, Positive-Displacement, Peristaltic & Diaphragm Pumps
Key Takeaways Explain This Topic AI
Match pump type to fluid, head, flow, solids, and accuracy needs.
Cavitation is a suction/pressure phenomenon diagnosed from several operating clues.
Actual flow and pressure verify performance; command signals alone do not.
Pump work requires control of electrical and stored hydraulic energy.
Last updated: September 2026
5.1 Centrifugal, Positive-Displacement, Peristaltic & Diaphragm Pumps
2025 WPI alignment: This section teaches centrifugal, positive-displacement, peristaltic, and diaphragm pumps in the official Equipment Evaluation, Maintenance, and/or Operation content area.
Why this job task matters
Pump selection and operation depend on flow, head, viscosity, solids, required metering accuracy, suction conditions, and safe isolation; no single pump type is best for every wastewater duty.
Core operating concepts
Concept What the operator must understand
Centrifugal pump An impeller adds velocity and the casing converts it to pressure; performance changes with system head and speed.
Positive displacement A fixed volume is displaced each cycle or revolution, suiting viscous sludge and metering but requiring discharge overpressure protection.
Peristaltic pump Rollers compress flexible tubing, isolating fluid from moving parts; tube wear, suction lift, and pulsation require attention.
Diaphragm metering pump A reciprocating diaphragm with check valves meters chemical; air binding, fouled checks, stroke, and backpressure affect accuracy.
Cavitation Local pressure below vapor pressure forms bubbles that collapse, causing noise, vibration, reduced flow, and pitting.
System curve and NPSH Available suction head, static head, friction, valve position, level, and speed determine the actual operating point.
Operating and maintenance workflow
Confirm the pump is correct for the service and inspect suction level, strainers, valves, priming/flooding, seal water, and discharge path.
Verify rotation after electrical work and keep a positive-displacement discharge path and relief protection available before starting.
Record flow, suction/discharge pressure, speed, motor current, vibration, temperature, noise, leakage, and run time.
Compare parallel pumps and exercise standby units so redundancy is real rather than only installed.
Calibrate chemical and polymer pumps by actual draw or discharge, not solely by control-screen percentage.
Isolate electrical, hydraulic, pneumatic, pressure, and gravity energy before opening a pump or line.
Diagnostic evidence
Signal Likely meaning Defensible first response
Gravel-like noise and vibration Cavitation from poor suction conditions is likely Check liquid level, suction blockage, valve position, air leaks, temperature, and required NPSH.
High current with low flow Ragged impeller, binding, wrong rotation, or discharge problem may exist Verify lineup and condition under safe isolation.
Metering pump runs but no feed Air lock, empty source, fouled checks, tubing failure, or lost prime is possible Confirm inventory and purge/service under the chemical SOP.
Pump cycles too often Control band, wet-well volume, inflow, check valve, or level signal may be wrong Verify level and backflow before changing starts.
Calculation, control, or records connection
WPI provides water horsepower = flow (gpm) × head (ft) / 3,960 and brake or motor horsepower formulas that divide by the appropriate efficiency decimals. It also provides wire-to-water efficiency. Keep water horsepower, brake horsepower, and motor input distinct. A computed efficiency above 100 percent signals a unit, instrument, or formula error—not exceptional equipment.
Worked operator scenario
A centrifugal RAS pump becomes noisy, vibration rises, discharge flow falls, and the wet-well level is low. The evidence supports suction-side cavitation. The operator reduces stress if authorized, checks level control, suction valves, obstructions, and air entry, and avoids throttling the suction further. Replacing the motor would not address vapor formation at the impeller eye.
Common exam traps
Positive-displacement pumps must not be started against a blocked discharge without pressure protection.
Throttling a centrifugal suction is not a safe cure for excess flow and can worsen cavitation.
A controller’s speed or stroke percentage does not prove actual delivered flow.
Efficiency formulas require decimals such as 0.75, not the whole number 75.
Field-to-exam checklist
Match pump type to fluid, head, flow, solids, and accuracy needs.
Cavitation is a suction/pressure phenomenon diagnosed from several operating clues.
Actual flow and pressure verify performance; command signals alone do not.
Pump work requires control of electrical and stored hydraulic energy.
Match the pump to the system
A pump’s nameplate flow is not its installed duty. Centrifugal flow follows the intersection of the pump and system curves, which changes with static head, friction, valve position, speed, and impeller condition. Positive-displacement flow is less sensitive to discharge head, so blocked-discharge pressure protection becomes especially important. When output falls, compare suction level, discharge pressure, speed, current, vibration, noise, valve lineup, and a verified flow measurement. That evidence separates cavitation, air binding, wear, obstruction, and downstream restriction.
Affinity relationships and suction control
For a centrifugal pump at a fixed impeller diameter, the affinity laws describe how speed changes performance: flow varies directly with speed, head varies with the square of speed, and shaft power varies with the cube of speed. Reducing speed to 50 percent therefore delivers about half the flow, one quarter of the head, and roughly one eighth of the power. That cubic relationship is why variable-frequency drives pay for themselves on friction-dominated systems — and why they save far less on a system dominated by static lift, where the pump must still generate the same static head before any flow moves at all.
Worked speed change. A pump delivering 1,200 gpm at 1,750 rpm is slowed to 1,500 rpm. Expected flow = 1,200 x (1,500 / 1,750) = 1,029 gpm , and expected head falls to about 73 percent of the original value. If the measured flow is far below that, the system curve — not the drive — has changed.
Net positive suction head available (NPSHA) equals atmospheric pressure head plus static suction head, minus the liquid's vapor pressure head, minus suction friction losses. It must exceed the pump's required NPSH with margin, or the liquid flashes at the impeller eye and the pump cavitates. Everything that lowers NPSHA is an operating decision: a falling wet-well level, a partly closed or plugged suction valve, a fouled strainer, a warmer liquid, or a longer suction run.
Specialty impellers trade efficiency for reliability. Chopper and grinder pumps cut solids at the inlet; recessed-impeller (vortex) pumps pass large solids by moving liquid in a swirl above the impeller. Both consume more energy per gallon than a closed-impeller pump and are still the correct choice in rag-heavy service. Finally, two identical pumps in parallel do not double flow on a steep system curve, while the same two in series add head at roughly the same flow.