Study guide

3.5 Wells, Water Levels & Sanitary Condition

ABC/WPI Water Distribution Operator Class I Certification Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Certification, Eligibility & the WPI/ABC System 1.3 Study Plan & How to Use This Guide

2 Distribution Components — Pipes, Joints & Fittings

2.1 Mains & Service Lines 2.2 Pipe Materials (PVC, DI, CI, AC, HDPE, Copper, Steel) 2.3 Joints, Fittings & Thrust Restraint

3 Distribution Components — Valves, Hydrants, Storage & Wells

3.1 Valves (Gate, Butterfly, Check, PRV, Air Release, Blow-off) 3.2 Fire Hydrants 3.3 Storage Facilities (Ground, Elevated, Hydropneumatic) 3.4 Pumps & Pump Stations 3.5 Wells, Water Levels & Sanitary Condition

4 Meters, Backflow Devices, SCADA, Hydraulics & Demand

4.1 Meters & Metering (AMR/AMI) 4.2 Backflow Prevention Devices (Air Gap, RPZ, DCVA, PVB) 4.3 SCADA & Instrumentation 4.4 Distribution Hydraulics: Pressure, C-factor, Head Loss 4.5 System Demand, Water Production & Design Basics

5 Installation — Excavation, Bedding & Sewer Separation

5.1 Excavation Safety & Trenching (OSHA Subpart P) 5.2 Bedding, Backfill & Thrust Blocks 5.3 Separation from Sewer Mains

6 Installation — Pressure Testing & Disinfection

6.1 AWWA C600 Hydrostatic Pressure Testing 6.2 AWWA C651 Disinfection of New Mains 6.3 Service Line Installation, Tapping & Main Repairs

7 Operations & Maintenance

7.1 Valve Exercising & Hydrant Maintenance 7.2 Flushing & Unidirectional Flushing 7.3 Storage Facility Cleaning & Disinfection 7.4 Meter Reading & Underground Locating

8 Water Quality Monitoring & Lab Analysis

8.1 Disinfection Principles: Free vs Combined Chlorine, Breakpoint 8.2 Chemical Dosage & Feed Equipment 8.3 Sample Collection & Lab Analysis (Chlorine Residual, pH, Turbidity) 8.4 Lab Interpretation & Distribution Water Quality Problems

9 Regulations, Sampling & Public Notification

9.1 SDWA & Federal Drinking Water Regulations 9.2 Revised Total Coliform Rule (RTCR) 9.3 Lead & Copper Rule Revisions (LCRR) 9.4 Public Notification, CCR & Sampling Techniques

10 Safety, Security & Administrative Procedures

10.1 PPE, Safe Work Practices & Lockout/Tagout 10.2 Traffic Control (MUTCD) & Confined Space Entry 10.3 Underground Locating (811) & APWA Color Codes 10.4 Cross-Connection Control Program & Hazard Levels 10.5 System Maps, Schematics, Plans & Asset Management

11 Security, Records, Math Review & Final Readiness

11.1 Emergency Response, Facility Security & Water Loss Control 11.2 Recordkeeping, SOPs & Customer Inquiries 11.3 Operator Math: Flow, Pressure, Head & Pipe Volume 11.4 Operator Math: Chemical Feed & Chlorine Dose 11.5 Full-Length Practice & Test-Day Strategy

3.5 Wells, Water Levels & Sanitary Condition

Key Takeaways Explain This Topic AI

Drawdown = pumping water level − static water level; specific capacity = yield (gpm) ÷ drawdown (ft), and a falling specific capacity signals screen encrustation, biofouling, or sand infiltration.

A stable static level with growing drawdown points to a well problem; a falling static level points to an aquifer decline.

Sanitary condition requires casing at least 12 in above finished grade, a gasketed sanitary seal or watertight cap, a downward-turned 24-mesh screened vent, a grouted annulus, and grade sloping away from the wellhead.

AWWA C654 governs well disinfection: at least 100 mg/L chlorine initially, at least 50 mg/L free chlorine maintained through the water column, and at least 8 hours of contact.

Water levels must always be measured from the same recorded reference point, normally the top of casing, or the trend becomes meaningless.

Last updated: August 2026

3.5 Wells, Water Levels & Sanitary Condition

Most Class I distribution systems are groundwater systems , and in a small utility the same operator who exercises valves also reads the well. The Need-to-Know Criteria reflect that: wells appear in Distribution System Components ("understand wells and related equipment — measure static water levels and pumping water levels") and again twice in Equipment Installation, Operation, Maintenance, and Repair ("maintain well and related equipment" and "maintain the sanitary condition of the well"). You are not expected to design or drill a well, but you are expected to read its levels, keep it sanitary, and recognize when it is failing.

Well Components

Component Function Operator concern

Casing Steel or PVC pipe that holds the borehole open and seals out shallow water Must extend ≥12 in above finished grade ; check for holes, corrosion, damage

Annular seal (grout) Cement or bentonite filling the space between casing and borehole Blocks surface water from running down the outside of the casing

  • Screen Slotted section that admits water from the aquifer Plugs with mineral scale and biofilm over time
  • Filter (gravel) pack Graded gravel around the screen Keeps fines out of the well
  • Pump Vertical turbine (line shaft) or submersible Cavitation, bearing wear, motor amps
  • Drop/column pipe Carries water from pump to surface Corrosion, joint leaks
  • Sanitary seal / well cap Watertight cap on top of casing Gasketed, bolted, tamper-resistant
  • Screened vent Allows air exchange as level rises and falls Turned downward , 24-mesh or finer
  • Sounding tube or airline Access for measuring water level Keep clear and capped

Check valve, flow meter, sample tap Prevent backflow, measure yield, allow raw sampling Sample tap goes before any chemical addition

Static Level, Pumping Level, and Drawdown

Three measurements describe how a well is performing, and the exam expects you to tell them apart:

Static water level (SWL) — the depth from a fixed reference point (normally the top of the casing) down to the water surface when the pump has been off long enough for the level to recover and stabilize.

Pumping water level (PWL) — the depth to the water surface while the pump is running at a steady rate.

Drawdown — the difference between them: Drawdown = PWL − SWL , expressed in feet.

When a well pumps, water flows toward the well from all directions and the water table around it drops into a cone of depression . The horizontal distance out to where drawdown becomes negligible is the radius of influence . Both grow as pumping rate or duration increases, which is why nearby wells can interfere with each other.

Worked example. A well has a static water level of 60 ft and, after pumping steadily at 250 gpm, the level settles at 95 ft.

Drawdown = 95 − 60 = 35 ft .

Specific Capacity — The Well's Report Card

Divide the yield by the drawdown and you get specific capacity , the single most useful trend number an operator tracks on a well:

Specific capacity (gpm/ft) = Yield (gpm) ÷ Drawdown (ft)

For the well above: 250 gpm ÷ 35 ft = 7.1 gpm/ft .

Specific capacity is only meaningful as a trend . Record it at the same pumping rate each time. A steady decline — say from 7.1 to 4.5 gpm/ft over several years — means the well is losing efficiency, and there are only a few causes: mineral encrustation (calcium carbonate, iron) plugging the screen slots, biofouling by iron bacteria, sand infiltration filling the bottom, or a genuine aquifer decline that also shows up as a falling static level. The distinguishing clue is the static level: if static is stable but drawdown grows, the problem is at the well; if static itself is falling, the problem is the aquifer.

Measuring Water Levels

Electric sounder (water-level tape) — a weighted probe on a marked tape that beeps or lights when it touches water. The most common and most accurate field method.

Airline and pressure gauge — a small tube of known length runs down the casing; air is pumped in until the gauge stops rising, and the reading converts to submergence at 2.31 ft per psi .

Pressure transducer — a submerged sensor reporting continuous level to SCADA, which is how larger systems trend drawdown automatically.

Always measure from the same reference point and record it. A level "60 ft" from the top of casing and "58 ft" from ground surface are the same water, described two ways, and mixing them corrupts the trend.

Maintaining the Sanitary Condition of the Well

A well is a direct opening into the aquifer, so sanitary defects are contamination pathways. The recurring requirements — checked on every sanitary survey — are:

Casing height — terminates at least 12 in above finished grade , and well above any known flood level.

Surface drainage — the ground slopes away from the casing so runoff cannot pond at the wellhead.

Sanitary seal / watertight cap — gasketed and bolted; a pitless adapter installation uses a watertight cap.

Screened vent — turned down , secured, tamper-resistant, and screened at 24-mesh or finer to exclude insects.

Grouted annulus — no unsealed space alongside the casing.

No cross-connections — the discharge, blow-off, and any chemical feed are protected against backflow.

Setbacks — the required separation from septic systems, sewers, and fuel storage is maintained, and the wellhead protection area designated under the state's SDWA §1428 program is respected.

Maintenance and Disinfection

Routine well maintenance means trending water levels, yield, and motor amps; inspecting the cap, vent, and slab; testing the raw sample tap; and scheduling pump pulls on condition rather than after failure. Rehabilitation of a plugged screen uses mechanical brushing/surging, chemical treatment, or both.

Any time the well is opened — new construction, pump pull, screen work, or a suspected contamination event — it must be disinfected before it goes back into service. AWWA C654, Disinfection of Wells , is the governing standard: the water column is dosed to at least 100 mg/L chlorine initially, at least 50 mg/L free chlorine is maintained throughout the column, and contact is held for at least 8 hours . Afterward the well is pumped to waste until the residual matches normal distribution levels, and bacteriological samples must come back coliform-free before the source is returned to service. Do not confuse this with C651 (mains) or C652 (storage) — the exam mixes the three deliberately.