Study guide
7.4 Meter Reading & Underground Locating
ABC/WPI Water Distribution Operator Class I Certification Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Certification, Eligibility & the WPI/ABC System 1.3 Study Plan & How to Use This Guide
2 Distribution Components — Pipes, Joints & Fittings
2.1 Mains & Service Lines 2.2 Pipe Materials (PVC, DI, CI, AC, HDPE, Copper, Steel) 2.3 Joints, Fittings & Thrust Restraint
3 Distribution Components — Valves, Hydrants, Storage & Wells
3.1 Valves (Gate, Butterfly, Check, PRV, Air Release, Blow-off) 3.2 Fire Hydrants 3.3 Storage Facilities (Ground, Elevated, Hydropneumatic) 3.4 Pumps & Pump Stations 3.5 Wells, Water Levels & Sanitary Condition
4 Meters, Backflow Devices, SCADA, Hydraulics & Demand
4.1 Meters & Metering (AMR/AMI) 4.2 Backflow Prevention Devices (Air Gap, RPZ, DCVA, PVB) 4.3 SCADA & Instrumentation 4.4 Distribution Hydraulics: Pressure, C-factor, Head Loss 4.5 System Demand, Water Production & Design Basics
5 Installation — Excavation, Bedding & Sewer Separation
5.1 Excavation Safety & Trenching (OSHA Subpart P) 5.2 Bedding, Backfill & Thrust Blocks 5.3 Separation from Sewer Mains
6 Installation — Pressure Testing & Disinfection
6.1 AWWA C600 Hydrostatic Pressure Testing 6.2 AWWA C651 Disinfection of New Mains 6.3 Service Line Installation, Tapping & Main Repairs
7 Operations & Maintenance
7.1 Valve Exercising & Hydrant Maintenance 7.2 Flushing & Unidirectional Flushing 7.3 Storage Facility Cleaning & Disinfection 7.4 Meter Reading & Underground Locating
8 Water Quality Monitoring & Lab Analysis
8.1 Disinfection Principles: Free vs Combined Chlorine, Breakpoint 8.2 Chemical Dosage & Feed Equipment 8.3 Sample Collection & Lab Analysis (Chlorine Residual, pH, Turbidity) 8.4 Lab Interpretation & Distribution Water Quality Problems
9 Regulations, Sampling & Public Notification
9.1 SDWA & Federal Drinking Water Regulations 9.2 Revised Total Coliform Rule (RTCR) 9.3 Lead & Copper Rule Revisions (LCRR) 9.4 Public Notification, CCR & Sampling Techniques
10 Safety, Security & Administrative Procedures
10.1 PPE, Safe Work Practices & Lockout/Tagout 10.2 Traffic Control (MUTCD) & Confined Space Entry 10.3 Underground Locating (811) & APWA Color Codes 10.4 Cross-Connection Control Program & Hazard Levels 10.5 System Maps, Schematics, Plans & Asset Management
11 Security, Records, Math Review & Final Readiness
11.1 Emergency Response, Facility Security & Water Loss Control 11.2 Recordkeeping, SOPs & Customer Inquiries 11.3 Operator Math: Flow, Pressure, Head & Pipe Volume 11.4 Operator Math: Chemical Feed & Chlorine Dose 11.5 Full-Length Practice & Test-Day Strategy
7.4 Meter Reading & Underground Locating
Key Takeaways Explain This Topic AI
Meters are read in gallons or cubic feet; a low or zero reading may indicate a leak or a stuck meter, and a sudden high reading often signals a leak or irrigation use.
811 Call Before You Dig is the one-call service that alerts utility owners to mark underground lines before excavation.
APWA color codes mark utilities on the surface: blue=water, green=sewer, yellow=gas, red=electric, orange=telecom, pink=survey, white=proposed excavation, purple=reclaimed water.
Electronic locating uses conductive (direct connect to tracer wire or appurtenance) and inductive (no connection) methods to find buried non-metallic pipe.
Non-metallic water mains are found by a tracer wire laid in the trench; metallic pipe can be located conductively without a wire.
Last updated: August 2026
7.4 Meter Reading & Underground Locating
Quick Answer: Meters are read in gallons or cubic feet; abnormal readings flag leaks, stuck registers, or tamper. Before any excavation, 811 Call Before You Dig routes utility marks to the surface using APWA color codes — blue for water, green for sewer, yellow for gas, red for electric, orange for telecom . Buried non-metallic mains are found with tracer wire and an electronic locator using conductive or inductive methods.
Meter Reading
A water meter measures the volume of water delivered to a customer, typically in gallons or cubic feet . The register is read like an odometer — leftmost digits are the largest place values, rightmost are the smallest. Two reading technologies dominate the field:
Manual reading — an operator walks to the meter, lifts the lid, and reads the register visually.
Automated Meter Reading (AMR) — a drive-by or walk-by radio transmits the reading to a receiver, eliminating visual reads.
Advanced Metering Infrastructure (AMI) — fixed-network two-way communication provides real-time reads, leak alerts, and tamper flags without a visit.
Reading and Troubleshooting
The reading itself is straightforward — subtract the prior reading from the current reading to get consumption for the billing period. The diagnostic value is in the pattern:
- Reading pattern Likely cause
- Zero or near-zero consumption Stuck meter, no occupancy, or closed customer valve
- Low but non-zero consumption (a steady trickle) Customer-side leak (running toilet, dripping faucet)
- Sudden high consumption Leak, irrigation startup, or filling a pool
- Readings that go backward Faulty register or reverse flow
- Physical tamper indicators Broken wire seal, inverted cover, magnetic interference
A meter flagged for low or no consumption is tested for accuracy; if it passes, the issue is on the customer side (leak or vacancy). A high-consumption alert is the operator's first contact point for a customer leak investigation. Meters should also be right-sized for the expected flow — an oversized meter under-registers low flows, and an undersized meter causes pressure loss.
811 Call Before You Dig
Before any excavation — a main repair, service tap, or new connection — the operator calls 811 , the national one-call number, which routes the request to the local one-call center. The one-call center notifies every member utility with facilities in the dig area, and each utility sends a locator to mark its lines with surface paint or flags. Excavation must wait until the marks are in place (state law typically requires 48–72 hours' notice). Marks are good for a limited window, often 30 days, and a re-mark is needed if the dig is delayed.
APWA Color Codes
The American Public Works Association (APWA) Uniform Color Code is the national standard for temporary surface marking of underground utilities. The codes are easy to remember and must be honored by every excavator:
- Color Utility
- Red Electric power lines, cables, conduit, lighting
- Yellow Gas, oil, petroleum, steam
- Orange Telecommunications, alarm, CATV, signal
- Blue Potable water
- Green Sewers, drain lines
- Purple Reclaimed water, irrigation reuse
- Pink Temporary survey markings
- White Proposed excavation limits
A water-distribution operator expects to see blue marks for water mains and services and may also see purple marks if the system carries reclaimed water. The operator must respect every color, not just blue — striking a yellow gas line or red electric line while repairing a water main is the kind of cross-utility failure that kills people.
Electronic Locating
Paint marks tell the excavator where the line is; they do not by themselves find a buried main. The marks come from an electronic locator that traces the line from the surface. Two methods are used:
Conductive locating — the locator clips a transmitter directly to the pipe, a tracer wire, or an appurtenance (hydrant, valve, meter setter). Current flows through the conductive pipe or wire, and the receiver detects the electromagnetic field above ground. Conductive locating is accurate and preferred whenever a connection point is available.
Inductive locating — the transmitter is placed on the ground above the suspected line without a direct connection. The transmitter induces a current into the buried conductor; the receiver reads the resulting field. Inductive is used when no access point exists but is less precise and more prone to interference from adjacent lines.
Tracer Wire for Non-Metallic Pipe
Most modern small-diameter water services and many mains are PVC, HDPE, or other non-metallic materials , which are invisible to an electronic locator on their own. To make them locatable, a tracer wire is laid in the trench alongside the pipe and brought up at each appurtenance. The locator connects conductively to the tracer wire and follows it. A broken or unconnected tracer wire is a common reason a main cannot be found — a good practice is to test tracer-wire continuity at every new installation and every repair. Some systems now use tracer tape (a metallic strip buried above the pipe) as a backup, though tracer wire with a direct connection point remains the most reliable method.
Putting It Together
The routine on any excavation is: call 811, wait for the marks, hand-dig within the tolerance zone around the marks (typically 18–24 inches on either side), respect every color, and use an electronic locator to refine the mark when a tracer wire or metallic pipe is present. The same field crew often reads meters and calls in locates, so both skills belong in a Class I operator's toolkit.