Study guide

11.1 Raw-Water Intakes, Screening, and Pumps

WPI Water Treatment Operator Class I Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Treatment Calculations

1.1 Chemical Use and Dose Calculations 1.2 Flow, Volume, and Detention 1.3 Filter, Backwash, and Residuals Math

2 Process Data and Automation

2.1 SCADA, PLC, HMI, and Data Links 2.2 Gauges, Meters, Analyzers, and Trends

3 Pretreatment and Floc Formation

Source-Water Treatment and Pretreatment Coagulation and Rapid Mix Flocculation Control

4 Clarification and Filtration

4.1 Clarification and Sedimentation 4.2 Conventional Filtration 4.3 Direct, Pressure, and Cartridge Filtration

5 Barrier Performance and Residuals

5.1 Membrane Filtration and Integrity 5.2 Filter Performance and Backwash 5.3 Plant Residuals Handling and Disposal

6 Chemical and Disinfection Control

6.1 Iron and Manganese Treatment 6.2 Disinfectant Dose, Contact, and Residual 6.3 Chemical Preparation, Feed, and Uses

7 Integrated Plant Operations

7.1 Plant Control, Troubleshooting, and Optimization 7.2 Operating Records and System Interface

8 Laboratory Quality and Sampling

8.1 Laboratory Equipment and Quality Checks 8.2 Representative Water Sampling 8.3 Preservation, Custody, and Documentation

9 Physical and Disinfectant Analysis

9.1 Color, Taste, Odor, and Temperature 9.2 Turbidity and Suspended Solids 9.3 Free, Combined, and Total Chlorine

10 Chemical and Microbial Analysis

10.1 pH, Alkalinity, and Hardness 10.2 Iron and Manganese Analysis 10.3 Disinfection Byproduct Analysis 10.4 Bacteriological Analysis and Response

11 Water Movement Equipment

11.1 Raw-Water Intakes, Screening, and Pumps 11.2 Potable Pumps, Drivers, and Demand 11.3 Valves, Process Meters, and Flow Control

12 Chemical Process Equipment

12.1 Mixers and Flocculators 12.2 Chemical Feed Equipment 12.3 Chlorine Disinfection Systems

13 Filtration, Storage, and Piping

13.1 Conventional Filter Equipment 13.2 Water Storage Tank Equipment 13.3 Facility Piping and Auxiliary Systems

14 Instrumentation and Controls

14.1 PLC and HMI Operation 14.2 SCADA Operation and Maintenance 14.3 Online Analyzers and Calibration

15 Reliability and Asset Management

15.1 Motors, Compressors, and Blowers 15.2 Emergency Systems and Backup Power 15.3 Three Maintenance Modes 15.4 Assets, Work Orders, and Records

16 Source-Water Quality

16.1 Biological Source-Water Characteristics 16.2 Chemical Source-Water Characteristics 16.3 Physical Source-Water Characteristics

17 Source Supply and Wells

17.1 Contamination Sources and Susceptibility 17.2 Source Supply, Yield, and Demand 17.3 Static Level, Pumping Level, and Drawdown

18 Source Protection

18.1 Groundwater Source Inspection 18.2 Wellhead Protection Plans 18.3 Watershed Management Plans

19 Chemical and Workplace Safety

19.1 Chemical Receiving, Unloading, and Storage 19.2 SDS, PPE, Training, and Disposal

20 Safe Work and Emergency Response

20.1 Hazardous Work Controls 20.2 Emergency Plans and Incident Response

21 Security, Compliance, and Administration

21.1 Physical Security and Cybersecurity 21.2 Compliance, Permits, and Public Notice 21.3 SOPs, Records, Inventory, and Supervision

11.1 Raw-Water Intakes, Screening, and Pumps

Key Takeaways Explain This Topic AI

An intake is an equipment train: source opening, screening, conveyance, pump suction, pump, and discharge must all support dependable raw-water delivery.

A rising level difference across a screen, worsening suction conditions, and falling flow together support an obstruction diagnosis more strongly than any single indication.

Cavitation forms when local liquid pressure falls below vapor pressure; noise, vibration, reduced head, and worsening performance require a controlled response under the plant SOP.

Operators verify lineup, intake level, prime or flooded suction, lubrication, guards, and a valid discharge path before starting a raw-water pump.

Raw-water equipment records should preserve operating context, measured values, observations, actions, and the response—not merely state that a check was completed.

Last updated: July 2026

Treat the intake as one equipment train

The 2025 Water Professionals International (WPI) Class I outline specifically requires operators to inspect, maintain, and operate raw-water intake, screening, and pumping equipment. The exam may therefore connect an intake symptom to a screen, suction path, or pump rather than naming the failed component. An intake can include a source opening, trash rack or coarse screen, finer screen, conduit, wet well, suction piping, pump, check valve, and discharge piping. Actual arrangements differ, so the plant's drawings, standard operating procedure (SOP), manufacturer instructions, and authorized operating limits control.

Screening protects pumps and downstream equipment from sticks, vegetation, trash, ice, mussels, and other debris. It does not make raw water potable. A fixed rack may need approved mechanical or manual cleaning; a traveling screen may include a drive, spray wash, chain, bearings, and debris handling. Never bypass a protective screen, enter water, reach into moving equipment, or enter an intake space to restore flow. Cleaning and maintenance require the facility's isolation, lockout/tagout, access, and environmental controls.

Observation What it may indicate Evidence to check next

Upstream level rises while downstream level falls Increasing screen loss or blocked passage Differential level or head, visible debris, screen drive and wash system

Raw-water flow falls and suction pressure worsens Restricted intake/suction, low source level, or air entry Source and wet-well levels, valve lineup, screen condition, suction leaks

Motor current changes but indicated flow does not Hydraulic change, pump problem, or bad indication Discharge pressure, independent flow evidence, noise and vibration

Repeated screen-drive trip Jam, overload, misalignment, or failed drive component Alarm history and inspection after safe isolation

A single reading is a clue, not a diagnosis. First confirm instrument status and compare related indications. A plugged sensing line can imitate a screen problem; a failed flow transmitter can imitate a pump problem. Separate loss of source supply from loss of pumping capacity: a declining river, reservoir, or wet-well level affects every available unit, while one unit's abnormal pressure, current, or vibration can isolate a machine problem. Compare like-for-like pumps only under comparable hydraulic conditions. Even a standby unit that appears normal may share the same obstructed intake, so its start is both a continuity action and a carefully interpreted diagnostic observation.

Make readiness visible before a start

Before starting, identify the correct pump and review its status. Under the site SOP, confirm adequate source or wet-well level; an open suction path; acceptable screen condition; correct valve lineup; a primed or flooded suction where the design requires it; lubrication and seal-support readiness; installed guards; available power; and a valid discharge path. Pump type and installation determine the exact valve sequence, so no generic sequence should replace the approved one.

After start, verify that the machine actually established service. Observe suction and discharge pressure, flow, motor current, noise, vibration, leakage, and bearing or winding temperature indications available to the operator. Compare them with the unit's normal baseline and pump curve, not with an invented universal value. Confirm that intake level remains stable enough for the required supply. A permissive or green screen icon shows that control logic allowed a command; field evidence shows whether water moved as intended.

Recognize cavitation without unsafe investigation

Cavitation occurs when local static pressure falls below the water's vapor pressure, vapor bubbles form, and those bubbles collapse in a higher-pressure region. DOE guidance identifies crackling or marble-like noise, vibration, reduced head or flow, and impeller damage as important consequences. Low suction pressure, a fouled suction path, air pockets, excessive flow, or unsuitable operating conditions can contribute. Similar noise can have other causes, so diagnose from multiple observations.

If a running raw-water pump suddenly becomes noisy while suction pressure drops and screen differential rises, do not tighten packing, change protected settings, or open equipment while it runs. Follow the upset SOP: verify the readings, protect supply with an authorized standby path if available, reduce or stop the affected unit when required, notify the responsible operator, and inspect only after the proper energy and hydraulic isolation. Restoring suction conditions addresses the cause; simply restarting the same condition invites damage.

Use trends to separate cause from consequence

Consider a plant where raw-water flow slowly declines over two hours. Discharge pressure, motor current, and downstream wet-well level also drift, while the differential across a traveling screen climbs. That time-aligned pattern supports accumulating debris more strongly than an abrupt transmitter failure. The operator checks the screen wash and drive status, validates the level indications, follows the approved cleaning or standby-intake procedure, and watches whether all values recover together. If flow remains low after screen loss returns to normal, the pump or another restriction still needs investigation.

Record the pump ID, operating hours, source and wet-well levels, screen differential, suction/discharge pressures, flow, motor current, abnormal noise or vibration, alarms, debris conditions, action, and post-action result. These data let the next shift distinguish seasonal loading from equipment deterioration.

  • Official source trail
  • WPI 2025 Water Treatment Operator Class I Need-to-Know
  • EPA Turbidity Provisions Guidance Manual, treatment-process discussion
  • EPA Sanitary Survey Learner's Guide
  • DOE Improving Pumping System Performance