Study guide

3.2 Temperature, Grouping & Installation Derating Factors for Dubai

Dubai Municipality DEQ Electrical Technical Staff Qualification Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DEWA Regulations and Approval Procedures

1.1 DEWA Low Voltage Supply Characteristics & Network Parameters 1.2 DEQ Qualification Scope and Applicant Requirements 1.3 Drawing Approval, NOCs, Inspection & Connection Workflows 1.4 Metering Enclosures, Labelling & Distribution Point Rules

2 Chapter 2: Earthing, Bonding and Protection

2.1 TN-S Earthing System & Earth Loop Impedance (Zs, Ze) 2.2 Equipotential and Supplementary Bonding Requirements 2.3 RCD/ELCB Protection Standards (30mA & Distribution RCDs) 2.4 Overcurrent Protection, Circuit Breakers & Discrimination

3 Chapter 3: Cable Sizing and Load Calculation

3.1 Conductor Selection & Current-Carrying Capacity 3.2 Temperature, Grouping & Installation Derating Factors for Dubai 3.3 Voltage Drop Limits & Calculation Methods 3.4 Connected Load, Maximum Demand & DEWA Diversity Factors

4 Chapter 4: BS 7671 Wiring and Installation Practice

4.1 IEC Conductor Colors, Wiring Methods & IP Ratings 4.2 Special Locations & Bathroom Zoning Requirements 4.3 Initial Verification: Dead & Live Electrical Testing Procedures 4.4 Fire-Resistant Wiring, Containment & Concealed Wiring Rules

5 Chapter 5: Substation and Transformer Requirements

5.1 Substation & Switchroom Layout, Ventilation & Clearances 5.2 Ring Main Units (RMU), Transformers & Switchgear 5.3 Fault Levels, Earth Electrodes & Step/Touch Potentials

6 Chapter 6: Electrical Theory and Safety

6.1 AC 3-Phase Calculations, Power Factor & Apparent Power 6.2 Safe Isolation, Lockout/Tagout & DEWA Safety Protocols

3.2 Temperature, Grouping & Installation Derating Factors for Dubai

Key Takeaways Explain This Topic AI

DEWA establishes standard base ambient temperatures of 45°C for cables installed in free air/conduit and 35°C for underground direct burial or duct installations.

Higher ambient temperatures reduce the temperature gradient available for thermal dissipation, requiring an ambient correction factor Ca to downscale tabulated cable capacities.

Grouping correction factor Cg accounts for mutual thermal heating among adjacent cables; cables touching in trunking or ladder racks experience capacity reductions up to 40-50%.

Enclosing cables in thermal building insulation drastically restricts heat dissipation, requiring a thermal insulation factor Ci = 0.50 when fully surrounded over lengths ≥ 500 mm.

The overall derating factor is the product of all applicable individual correction factors (Ctotal = Ca · Cg · Ci · Cf · Cs · Cd), directly inflating the required tabulated current rating It.

Last updated: July 2026

3.2 Temperature, Grouping & Installation Derating Factors for Dubai

Study focus: Dubai's harsh summer climate imposes severe thermal stress on electrical installations. DEWA enforces base ambient temperatures of 45 ∘ C 45^\circ\text{C} 4 5 ∘ C in air and 35 ∘ C 35^\circ\text{C} 3 5 ∘ C in ground. Candidates must know how to combine multiple correction factors ( C a , C g , C i , C f , C s , C d C_a, C_g, C_i, C_f, C_s, C_d C a ​ , C g ​ , C i ​ , C f ​ , C s ​ , C d ​ ) to calculate the overall derating multiplier and select compliant cable sizes.

Tabulated current-carrying capacities published in standard reference tables (such as BS 7671 Table 4E4A or IEC 60364) are based on standardized reference environmental conditions—typically 30 ∘ C 30^\circ\text{C} 3 0 ∘ C ambient air temperature in the UK/Europe and 20 ∘ C 20^\circ\text{C} 2 0 ∘ C ground temperature. Operating electrical cables in Dubai's extreme desert climate without proper derating will result in severe thermal overload, accelerated insulation breakdown, and catastrophic fire hazard.

The Dubai Climatic Context & DEWA Ambient Bases

During Dubai summer months (May through September):

Ambient shade air temperatures regularly exceed 45 ∘ C 45^\circ\text{C} 4 5 ∘ C to 48 ∘ C 48^\circ\text{C} 4 8 ∘ C .

External metal containment (conduits, cable trays, trunking exposed to direct solar radiation) can reach internal air temperatures exceeding 55 ∘ C 55^\circ\text{C} 5 5 ∘ C to 60 ∘ C 60^\circ\text{C} 6 0 ∘ C .

Unconditioned ceiling voids, roof plant rooms, and transformer enclosures frequently operate at 50 ∘ C 50^\circ\text{C} 5 0 ∘ C .

Ground temperatures at standard cable burial depths ( 0.8 m 0.8\text{ m} 0.8 m to 1.0 m 1.0\text{ m} 1.0 m ) reach 35 ∘ C 35^\circ\text{C} 3 5 ∘ C to 40 ∘ C 40^\circ\text{C} 4 0 ∘ C .

Because conductor current capacity is governed by the rate at which I 2 R I^2 R I 2 R electrical heat can dissipate into the surrounding environment, a higher ambient temperature reduces the thermal gradient ( Δ T = T max − T ambient \Delta T = T_{\text{max}} - T_{\text{ambient}} Δ T = T max ​ − T ambient ​ ), drastically lowering permissible continuous current. Thermal Dissipation Headroom (XLPE 90°C)

  • ┌─────────────────────────────────────────────────────────────────────────┐
  • │ Base 30°C Ambient Air: ΔT = 90°C - 30°C = 60°C Headroom (Ca = 1.00) │
  • ├─────────────────────────────────────────────────────────────────────────┤
  • │ Dubai 45°C Ambient Air: ΔT = 90°C - 45°C = 45°C Headroom (Ca = 0.87-0.90)│
  • ├─────────────────────────────────────────────────────────────────────────┤
  • │ Dubai 50°C Plant Room: ΔT = 90°C - 50°C = 40°C Headroom (Ca = 0.82) │
  • └─────────────────────────────────────────────────────────────────────────┘
  • DEWA Standard Base Ambient Temperatures

Cables Installed in Air / Trunking / Conduit: 45 ∘ C 45^\circ\text{C} 4 5 ∘ C base ambient air temperature .

Cables Buried Underground / in Ducts: 35 ∘ C 35^\circ\text{C} 3 5 ∘ C base ground temperature .

Ambient Temperature Correction Factor ( C a C_a C a ​ )

When using standard BS 7671 base tables (which assume a 30 ∘ C 30^\circ\text{C} 3 0 ∘ C air reference base), an ambient temperature correction factor C a C_a C a ​ must be applied.

The theoretical thermal rating factor follows the mathematical square-root relation: C a = T max − T ambient T max − T reference C_a = \sqrt{\frac{T_{\text{max}} - T_{\text{ambient}}}{T_{\text{max}} - T_{\text{reference}}}} C a ​ = T max ​ − T reference ​ T max ​ − T ambient ​ ​ ​

Where T max T_{\text{max}} T max ​ is 90 ∘ C 90^\circ\text{C} 9 0 ∘ C for XLPE and 70 ∘ C 70^\circ\text{C} 7 0 ∘ C for PVC.

Ambient Temp ( ∘ C ^\circ\text{C} ∘ C ) PVC Insulation ( 70 ∘ C 70^\circ\text{C} 7 0 ∘ C Max) XLPE Insulation ( 90 ∘ C 90^\circ\text{C} 9 0 ∘ C Max)

  • 30 ∘ C 30^\circ\text{C} 3 0 ∘ C 1.00 1.00 1.00 1.00 1.00 1.00
  • 35 ∘ C 35^\circ\text{C} 3 5 ∘ C 0.94 0.94 0.94 0.96 0.96 0.96
  • 40 ∘ C 40^\circ\text{C} 4 0 ∘ C 0.87 0.87 0.87 0.91 0.91 0.91

45 ∘ C 45^\circ\text{C} 4 5 ∘ C (DEWA Air Base) 0.79 0.79 0.79 0.87 0.87 0.87 (or 0.90 0.90 0.90 depending on reference table)

  • 50 ∘ C 50^\circ\text{C} 5 0 ∘ C (Plant Room / Sun) 0.71 0.71 0.71 0.82 0.82 0.82
  • 55 ∘ C 55^\circ\text{C} 5 5 ∘ C (Rooftop Conduit) 0.61 0.61 0.61 0.76 0.76 0.76

Notice that PVC suffers much steeper capacity loss than XLPE at elevated temperatures due to its lower maximum continuous thermal ceiling ( 70 ∘ C 70^\circ\text{C} 7 0 ∘ C vs 90 ∘ C 90^\circ\text{C} 9 0 ∘ C ).

Grouping Correction Factor ( C g C_g C g ​ )

When multiple power circuits or multi-core cables are installed in close physical proximity (bunched together in trunking, conduit, or stacked on cable trays), mutual thermal radiation prevents heat from escaping. The grouping correction factor C g C_g C g ​ penalizes closely packed cables.

Key Grouping Factors (BS 7671 Table 4C1)

Enclosed in Trunking or Conduit (Touching):

  • 2 2 2 circuits: C g = 0.80 C_g = 0.80 C g ​ = 0.80
  • 3 3 3 circuits: C g = 0.70 C_g = 0.70 C g ​ = 0.70
  • 4 4 4 circuits: C g = 0.65 C_g = 0.65 C g ​ = 0.65
  • 6 6 6 circuits: C g = 0.57 C_g = 0.57 C g ​ = 0.57
  • 9 9 9 circuits: C g = 0.50 C_g = 0.50 C g ​ = 0.50 (Cable current capacity is cut in half!)

Single Layer Touching on Perforated Cable Tray / Ladder:

  • 2 2 2 cables touching: C g = 0.88 C_g = 0.88 C g ​ = 0.88
  • 3 3 3 cables touching: C g = 0.82 C_g = 0.82 C g ​ = 0.82
  • 4 4 4 cables touching: C g = 0.77 C_g = 0.77 C g ​ = 0.77
  • 6 6 6 cables touching: C g = 0.73 C_g = 0.73 C g ​ = 0.73

Spaced Cable Installation ( 1 D 1 D 1 D Clearance):

Maintaining a physical gap equal to one cable diameter ( 1 D 1 D 1 D ) between adjacent cables allows free air convective cooling, keeping C g ≈ 0.95 − 1.00 C_g \approx 0.95 - 1.00 C g ​ ≈ 0.95 − 1.00 regardless of the number of cables.

Thermal Insulation Correction Factor ( C i C_i C i ​ )

When cables pass through or are embedded in building thermal insulation (e.g., glass wool, mineral fiber, or foam insulation in modern green building envelopes in Dubai):

Cable totally surrounded by thermal insulation over a length ≥ 500 mm \ge 500\text{ mm} ≥ 500 mm : C i = 0.50 C_i = 0.50 C i ​ = 0.50 (Capacity reduced by 50 % 50\% 50% ).

Cable in thermal insulation over 100 mm 100\text{ mm} 100 mm length: C i = 0.88 C_i = 0.88 C i ​ = 0.88 .

Cable in thermal insulation over 200 mm 200\text{ mm} 200 mm length: C i = 0.78 C_i = 0.78 C i ​ = 0.78 .

Cable in thermal insulation over 400 mm 400\text{ mm} 400 mm length: C i = 0.55 C_i = 0.55 C i ​ = 0.55 .

Ground & Underground Installation Factors ( C s , C d , C f C_s, C_d, C_f C s ​ , C d ​ , C f ​ )

For direct burial underground feeders or cables routed in subterranean ducts:

Soil Thermal Resistivity ( C s C_s C s ​ ): Standard ratings assume soil thermal resistivity of 1.2 K ⋅ m/W 1.2\text{ K}\cdot\text{m/W} 1.2 K ⋅ m/W . Dry sand or uncompacted backfill in Dubai has high resistivity (up to 2.0 K ⋅ m/W 2.0\text{ K}\cdot\text{m/W} 2.0 K ⋅ m/W ), yielding C s ≈ 0.85 C_s \approx 0.85 C s ​ ≈ 0.85 . Using thermally stabilized sand backfill maintains C s = 1.0 C_s = 1.0 C s ​ = 1.0 .

Depth of Burial ( C d C_d C d ​ ): Standard DEWA burial depth is 0.8 m 0.8\text{ m} 0.8 m under footpaths and 1.0 m 1.0\text{ m} 1.0 m under roadway crossings. Depths exceeding 1.5 m 1.5\text{ m} 1.5 m reduce heat loss, requiring C d ≈ 0.95 C_d \approx 0.95 C d ​ ≈ 0.95 .

Semi-Enclosed Ducting ( C f C_f C f ​ ): Cables routed in underground non-metallic ducts experience restricted air circulation compared to direct soil burial ( C f ≈ 0.85 − 0.90 C_f \approx 0.85 - 0.90 C f ​ ≈ 0.85 − 0.90 ).

Combined Derating Equation

The effective current-carrying capacity ( I z I_z I z ​ ) under combined site conditions is: I z = I t × ( C a ⋅ C g ⋅ C i ⋅ C f ⋅ C s ⋅ C d ) I_z = I_t \times (C_a \cdot C_g \cdot C_i \cdot C_f \cdot C_s \cdot C_d) I z ​ = I t ​ × ( C a ​ ⋅ C g ​ ⋅ C i ​ ⋅ C f ​ ⋅ C s ​ ⋅ C d ​ )

To size the required tabulated cable rating ( I t I_t I t ​ ): I t ≥ I n C a ⋅ C g ⋅ C i ⋅ C f ⋅ C s ⋅ C d I_t \ge \frac{I_n}{C_a \cdot C_g \cdot C_i \cdot C_f \cdot C_s \cdot C_d} I t ​ ≥ C a ​ ⋅ C g ​ ⋅ C i ​ ⋅ C f ​ ⋅ C s ​ ⋅ C d ​ I n ​ ​

  • Step-by-Step Worked Numerical Example
  • Problem Statement

A main sub-distribution feeder in a Dubai commercial high-rise connects a Main Distribution Board (MDB) to a secondary distribution panel located in an unconditioned rooftop HVAC plant room.

System Voltage: 3-phase, 400 V 400\text{ V} 400 V , 50 Hz 50\text{ Hz} 50 Hz .

Design Load Current ( I b I_b I b ​ ): 210 A 210\text{ A} 210 A .

Protective Device: 250 A 250\text{ A} 250 A 3-Pole MCCB ( I n = 250 A I_n = 250\text{ A} I n ​ = 250 A ).

Cable Type: 4-core Copper XLPE/SWA/LSZH cable.

Installation Condition: Installed on an open ladder rack in the rooftop plant room where peak summer ambient air temperature reaches 50 ∘ C 50^\circ\text{C} 5 0 ∘ C . The cable is touching 3 3 3 other fully loaded 3-phase cables in a single layer (total of 4 4 4 grouped cables touching on ladder rack).

Thermal Insulation: None ( C i = 1.0 C_i = 1.0 C i ​ = 1.0 ).

Calculate the required cable cross-sectional area.

Step 1: Identify Individual Derating Factors

Ambient Temperature Factor ( C a C_a C a ​ ): For XLPE insulation at 50 ∘ C 50^\circ\text{C} 5 0 ∘ C air ambient (relative to 30 ∘ C 30^\circ\text{C} 3 0 ∘ C base), C a = 0.82 C_a = 0.82 C a ​ = 0.82 .

Grouping Factor ( C g C_g C g ​ ): For 4 single-layer cables touching on a cable ladder, C g = 0.77 C_g = 0.77 C g ​ = 0.77 .

Other Factors: C i = 1.0 C_i = 1.0 C i ​ = 1.0 , C f = 1.0 C_f = 1.0 C f ​ = 1.0 .

Step 2: Compute Combined Derating Factor ( C total C_{\text{total}} C total ​ ) C total = C a × C g = 0.82 × 0.77 = 0.6314 C_{\text{total}} = C_a \times C_g = 0.82 \times 0.77 = 0.6314 C total ​ = C a ​ × C g ​ = 0.82 × 0.77 = 0.6314

Step 3: Determine Minimum Required Tabulated Capacity ( I t I_t I t ​ ) I t ≥ I n C total = 250 A 0.6314 = 395.95 A I_t \ge \frac{I_n}{C_{\text{total}}} = \frac{250\text{ A}}{0.6314} = 395.95\text{ A} I t ​ ≥ C total ​ I n ​ ​ = 0.6314 250 A ​ = 395.95 A

Step 4: Select Cable Cross-Section from BS 7671 Table 4E4A

Consult BS 7671 Table 4E4A (4-Core XLPE Armored Copper Cable, Method E in Air):

120 mm 2 120\text{ mm}^2 120 mm 2 Cu XLPE cable: I t = 358 A I_t = 358\text{ A} I t ​ = 358 A (Insufficient: 358 < 395.95 A 358 < 395.95\text{ A} 358 < 395.95 A )

150 mm 2 150\text{ mm}^2 150 mm 2 Cu XLPE cable: I t = 407 A I_t = 407\text{ A} I t ​ = 407 A (Sufficient: 407 ≥ 395.95 A 407 \ge 395.95\text{ A} 407 ≥ 395.95 A )

185 mm 2 185\text{ mm}^2 185 mm 2 Cu XLPE cable: I t = 461 A I_t = 461\text{ A} I t ​ = 461 A

Step 5: Verify Effective Derated Capacity ( I z I_z I z ​ ) I z = I t × C total = 407 A × 0.6314 = 256.98 A I_z = I_t \times C_{\text{total}} = 407\text{ A} \times 0.6314 = 256.98\text{ A} I z ​ = I t ​ × C total ​ = 407 A × 0.6314 = 256.98 A

Since I b ( 210 A ) ≤ I n ( 250 A ) ≤ I z ( 256.98 A ) I_b (210\text{ A}) \le I_n (250\text{ A}) \le I_z (256.98\text{ A}) I b ​ ( 210 A ) ≤ I n ​ ( 250 A ) ≤ I z ​ ( 256.98 A ) , the 150 mm 2 150\text{ mm}^2 150 mm 2 4-core Cu/XLPE/SWA/LSZH cable is fully compliant.