Study guide
6.1 AC 3-Phase Calculations, Power Factor & Apparent Power
Dubai Municipality DEQ Electrical Technical Staff Qualification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: DEWA Regulations and Approval Procedures
1.1 DEWA Low Voltage Supply Characteristics & Network Parameters 1.2 DEQ Qualification Scope and Applicant Requirements 1.3 Drawing Approval, NOCs, Inspection & Connection Workflows 1.4 Metering Enclosures, Labelling & Distribution Point Rules
2 Chapter 2: Earthing, Bonding and Protection
2.1 TN-S Earthing System & Earth Loop Impedance (Zs, Ze) 2.2 Equipotential and Supplementary Bonding Requirements 2.3 RCD/ELCB Protection Standards (30mA & Distribution RCDs) 2.4 Overcurrent Protection, Circuit Breakers & Discrimination
3 Chapter 3: Cable Sizing and Load Calculation
3.1 Conductor Selection & Current-Carrying Capacity 3.2 Temperature, Grouping & Installation Derating Factors for Dubai 3.3 Voltage Drop Limits & Calculation Methods 3.4 Connected Load, Maximum Demand & DEWA Diversity Factors
4 Chapter 4: BS 7671 Wiring and Installation Practice
4.1 IEC Conductor Colors, Wiring Methods & IP Ratings 4.2 Special Locations & Bathroom Zoning Requirements 4.3 Initial Verification: Dead & Live Electrical Testing Procedures 4.4 Fire-Resistant Wiring, Containment & Concealed Wiring Rules
5 Chapter 5: Substation and Transformer Requirements
5.1 Substation & Switchroom Layout, Ventilation & Clearances 5.2 Ring Main Units (RMU), Transformers & Switchgear 5.3 Fault Levels, Earth Electrodes & Step/Touch Potentials
6 Chapter 6: Electrical Theory and Safety
6.1 AC 3-Phase Calculations, Power Factor & Apparent Power 6.2 Safe Isolation, Lockout/Tagout & DEWA Safety Protocols
6.1 AC 3-Phase Calculations, Power Factor & Apparent Power
Key Takeaways Explain This Topic AI
DEWA LV distribution operates on a 3-phase, 4-wire system at 400V line-to-line and 230V line-to-neutral at 50 Hz frequency ( V L = 3 ⋅ V P V_L = \sqrt{3} \cdot V_P V L = 3 ⋅ V P ).
Active power ( P = 3 V L I L cos ϕ P = \sqrt{3} V_L I_L \cos\phi P = 3 V L I L cos ϕ ) represents real work in kW, Reactive power ( Q = 3 V L I L sin ϕ Q = \sqrt{3} V_L I_L \sin\phi Q = 3 V L I L sin ϕ ) maintains magnetic fields in kvar, and Apparent power ( S = 3 V L I L S = \sqrt{3} V_L I_L S = 3 V L I L ) defines total supply capacity in kVA.
In Star (Y) connections, line current equals phase current ( I L = I P I_L = I_P I L = I P ), while in Delta ( Δ \Delta Δ ) connections, line current is 3 \sqrt{3} 3 times phase current ( I L = 3 I P I_L = \sqrt{3} I_P I L = 3 I P ).
DEWA allows an overall power factor from 0.90 lagging to unity at customer intake points and recommends 0.95 lagging as a design target; designs must avoid leading power factor.
Capacitor bank sizing ( Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 ) Q_c = P \cdot (\tan\phi_1 - \tan\phi_2) Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 ) ) reduces line current, lowers thermal cable losses, and frees up transformer capacity.
Last updated: August 2026
6.1 AC 3-Phase Calculations, Power Factor & Apparent Power
In low-voltage electrical design and contracting across the Emirate of Dubai, mastering alternating current (AC) circuit theory and three-phase power calculations is an essential prerequisite for passing the Dubai Municipality DEQ technical-staff qualification for Electrical Fitting Contracting activity 453014. Electrical installations in Dubai operate under strict regulatory frameworks established by the DEWA Regulations for Electrical Installations . Understanding the mathematical relationships between voltage, current, active power, reactive power, apparent power, and power factor is critical to ensure electrical safety, system efficiency, and compliance with grid connection standards.
1. Fundamentals of AC Distribution in Dubai
The DEWA low-voltage (LV) electrical distribution grid operates as a three-phase, 4-wire system at a nominal frequency of 50 Hz . System voltages are standard across commercial, industrial, and residential developments:
- Nominal Phase-to-Neutral Voltage ( V P V_P V P ): 230 V ± 10 % 230\text{ V} \pm 10\% 230 V ± 10%
- Nominal Line-to-Line Voltage ( V L V_L V L ): 400 V ± 10 % 400\text{ V} \pm 10\% 400 V ± 10%
- System Frequency: 50 Hz ± 0.5 % 50\text{ Hz} \pm 0.5\% 50 Hz ± 0.5%
Earthing System: TN-S system (separate Neutral and Protective Earth conductors from the transformer throughout the installation).
The fundamental mathematical relationship between line voltage ( V L V_L V L ) and phase voltage ( V P V_P V P ) in a balanced three-phase system is derived from the 120 ∘ 120^\circ 12 0 ∘ phase displacement between the three phase vectors ( R R R , Y Y Y , B B B or L 1 L1 L 1 , L 2 L2 L 2 , L 3 L3 L 3 ): V L = 3 ⋅ V P ≈ 1.73205 × 230 V = 398.37 V ≈ 400 V V_L = \sqrt{3} \cdot V_P \approx 1.73205 \times 230\text{ V} = 398.37\text{ V} \approx 400\text{ V} V L = 3 ⋅ V P ≈ 1.73205 × 230 V = 398.37 V ≈ 400 V
Where:
V L V_L V L is the line-to-line RMS voltage ( 400 V 400\text{ V} 400 V ).
V P V_P V P is the phase-to-neutral RMS voltage ( 230 V 230\text{ V} 230 V ).
3 ≈ 1.732 \sqrt{3} \approx 1.732 3 ≈ 1.732 is the three-phase vector factor.
2. Single-Phase Power Triangle & Definitions
In single-phase AC circuits supplying inductive or capacitive loads, current and voltage sinusoidal waveforms are displaced by a phase angle ϕ \phi ϕ . This angular displacement gives rise to three distinct power quantities, represented visually by the Power Triangle :
Power Parameter Symbol Formula Units Physical Significance
Active (Real) Power P P P P = V ⋅ I ⋅ cos ϕ P = V \cdot I \cdot \cos\phi P = V ⋅ I ⋅ cos ϕ Watts (W) / Kilowatts (kW) Actual useful work performed (heat, mechanical torque, light output).
Reactive Power Q Q Q Q = V ⋅ I ⋅ sin ϕ Q = V \cdot I \cdot \sin\phi Q = V ⋅ I ⋅ sin ϕ Volt-Amperes Reactive (var) / kvar Sustains alternating electromagnetic fields in inductive coils (motors, transformers).
Apparent Power S S S S = V ⋅ I S = V \cdot I S = V ⋅ I Volt-Amperes (VA) / Kilovolt-Amperes (kVA) Total complex capacity required from DEWA grid transformers and cables.
Vector Relationships & Pythagorean Identity: S = P 2 + Q 2 S = \sqrt{P^2 + Q^2} S = P 2 + Q 2 Power Factor ( PF ) = cos ϕ = P S = Active Power (kW) Apparent Power (kVA) \text{Power Factor } (\text{PF}) = \cos\phi = \frac{P}{S} = \frac{\text{Active Power (kW)}}{\text{Apparent Power (kVA)}} Power Factor ( PF ) = cos ϕ = S P = Apparent Power (kVA) Active Power (kW)
3. Three-Phase Power Formulas & Load Configurations
In balanced three-phase systems, total electrical power is the vector sum of the power in all three individual phases. The formulas for total active, reactive, and apparent power depend on line values ( V L , I L V_L, I_L V L , I L ):
Three-Phase Active Power: P = 3 ⋅ V L ⋅ I L ⋅ cos ϕ P = \sqrt{3} \cdot V_L \cdot I_L \cdot \cos\phi P = 3 ⋅ V L ⋅ I L ⋅ cos ϕ
Three-Phase Reactive Power: Q = 3 ⋅ V L ⋅ I L ⋅ sin ϕ Q = \sqrt{3} \cdot V_L \cdot I_L \cdot \sin\phi Q = 3 ⋅ V L ⋅ I L ⋅ sin ϕ
- Three-Phase Apparent Power: S = 3 ⋅ V L ⋅ I L S = \sqrt{3} \cdot V_L \cdot I_L S = 3 ⋅ V L ⋅ I L
- Star (Y / Wye) vs. Delta ( Δ \Delta Δ ) Load Connections
Electrical equipment connected to a 3-phase supply can be configured in either Star (Y) or Delta ( Δ \Delta Δ ) :
Star (Y) Configuration:
Voltage: V L = 3 ⋅ V P ⟹ V P = V L 3 ≈ 230 V V_L = \sqrt{3} \cdot V_P \implies V_P = \frac{V_L}{\sqrt{3}} \approx 230\text{ V} V L = 3 ⋅ V P ⟹ V P = 3 V L ≈ 230 V .
Current: I L = I P I_L = I_P I L = I P (Line current equals phase winding current).
Neutral Conductor: The neutral point connects to the center of the star. In a balanced system, phase currents cancel out ( I N = I R + I Y + I B = 0 A I_N = I_R + I_Y + I_B = 0\text{ A} I N = I R + I Y + I B = 0 A ). In an unbalanced system, I N I_N I N carries the vector residual current.
Delta ( Δ \Delta Δ ) Configuration:
Voltage: V L = V P = 400 V V_L = V_P = 400\text{ V} V L = V P = 400 V (Full line voltage is applied across each phase winding).
Current: I L = 3 ⋅ I P ⟹ I P = I L 3 I_L = \sqrt{3} \cdot I_P \implies I_P = \frac{I_L}{\sqrt{3}} I L = 3 ⋅ I P ⟹ I P = 3 I L (Line current is 3 \sqrt{3} 3 times phase current).
Neutral Conductor: Delta systems have no neutral connection (3-wire system).
Parameter Star (Y) Connection Delta ( Δ \Delta Δ ) Connection
Line Voltage ( V L V_L V L ) V L = 3 ⋅ V P V_L = \sqrt{3} \cdot V_P V L = 3 ⋅ V P ( 400 V 400\text{V} 400 V ) V L = V P V_L = V_P V L = V P ( 400 V 400\text{V} 400 V )
Phase Voltage ( V P V_P V P ) V P = V L / 3 V_P = V_L / \sqrt{3} V P = V L / 3 ( 230 V 230\text{V} 230 V ) V P = V L V_P = V_L V P = V L ( 400 V 400\text{V} 400 V )
Line Current ( I L I_L I L ) I L = I P I_L = I_P I L = I P I L = 3 ⋅ I P I_L = \sqrt{3} \cdot I_P I L = 3 ⋅ I P
Phase Current ( I P I_P I P ) I P = I L I_P = I_L I P = I L I P = I L / 3 I_P = I_L / \sqrt{3} I P = I L / 3
- Neutral Connection Available (4-wire system) Not available (3-wire system)
- Typical Applications Distribution MDBs, Star-Delta Motor Starting Heavy motor windings, APFC capacitor banks
- 4. Power Factor Improvement & DEWA Regulations
Why Power Factor Matters:
An uncorrected, low lagging power factor ( cos ϕ < 0.85 \cos\phi < 0.85 cos ϕ < 0.85 ) caused by inductive loads (HVAC chillers, induction motors, magnetic ballasts, transformers) draws excessive line current for a given active kW load: I L = P 3 ⋅ V L ⋅ cos ϕ I_L = \frac{P}{\sqrt{3} \cdot V_L \cdot \cos\phi} I L = 3 ⋅ V L ⋅ cos ϕ P
Higher line current results in:
Higher thermal I 2 R I^2 R I 2 R losses in distribution cables and transformers.
Increased voltage drop across long cable runs.
Premature tripping of main circuit breakers due to overcurrent loading.
Overloading of DEWA grid supply infrastructure.
DEWA Power Factor Range and Design Recommendation:
Allowable Range: Maintain overall power factor between 0.90 lagging and unity at the intake point, without over-correcting into a leading condition.
Recommended Design Target: 0.95 lagging is a recommended target that provides operating margin; it is not a universal minimum threshold.
Capacitor Bank Sizing Formula:
To improve the power factor of a facility from an initial uncorrected value cos ϕ 1 \cos\phi_1 cos ϕ 1 to a target corrected value cos ϕ 2 \cos\phi_2 cos ϕ 2 (e.g., 0.95 or 0.97 lagging), parallel capacitor banks must supply reactive power ( Q c Q_c Q c ): Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 ) Q_c = P \cdot (\tan\phi_1 - \tan\phi_2) Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 )
Where:
Q c Q_c Q c = Required capacitor bank rating in kvar .
P P P = Active power of the load in kW .
tan ϕ 1 = tan ( arccos ( PF 1 ) ) = 1 − cos 2 ϕ 1 cos ϕ 1 \tan\phi_1 = \tan(\arccos(\text{PF}_1)) = \frac{\sqrt{1 - \cos^2\phi_1}}{\cos\phi_1} tan ϕ 1 = tan ( arccos ( PF 1 )) = c o s ϕ 1 1 − c o s 2 ϕ 1 .
tan ϕ 2 = tan ( arccos ( PF 2 ) ) = 1 − cos 2 ϕ 2 cos ϕ 2 \tan\phi_2 = \tan(\arccos(\text{PF}_2)) = \frac{\sqrt{1 - \cos^2\phi_2}}{\cos\phi_2} tan ϕ 2 = tan ( arccos ( PF 2 )) = c o s ϕ 2 1 − c o s 2 ϕ 2 .
Modern installations utilize Automatic Power Factor Correction (APFC) panels featuring microprocessor-based power factor controllers, heavy-duty contactors or thyristor switches, and 7% detuned harmonic reactors to protect capacitors from resonance with 5th and 7th harmonic currents generated by variable frequency drives (VFDs).
- 5. Step-by-Step Worked Numerical Examples
- Worked Example 6.1A: 3-Phase Industrial Chiller Calculation
Problem Statement: A commercial building in Dubai operates a 3-phase, 400V, 50 Hz central HVAC chiller motor drawing an active power P = 75 kW P = 75\text{ kW} P = 75 kW at an initial lagging power factor of cos ϕ 1 = 0.72 \cos\phi_1 = 0.72 cos ϕ 1 = 0.72 .
Determine:
The initial apparent power ( S 1 S_1 S 1 ) in kVA.
The initial full-load line current ( I L 1 I_{L1} I L 1 ) drawn from the DEWA main distribution panel.
The initial reactive power ( Q 1 Q_1 Q 1 ) in kvar.
Solution Step-by-Step:
Calculate Initial Apparent Power ( S 1 S_1 S 1 ): S 1 = P cos ϕ 1 = 75 kW 0.72 = 104.17 kVA S_1 = \frac{P}{\cos\phi_1} = \frac{75\text{ kW}}{0.72} = 104.17\text{ kVA} S 1 = cos ϕ 1 P = 0.72 75 kW = 104.17 kVA
Calculate Initial Line Current ( I L 1 I_{L1} I L 1 ): I L 1 = P ⋅ 1000 3 ⋅ V L ⋅ cos ϕ 1 = 75000 1.73205 × 400 × 0.72 = 75000 498.83 ≈ 150.35 A I_{L1} = \frac{P \cdot 1000}{\sqrt{3} \cdot V_L \cdot \cos\phi_1} = \frac{75000}{1.73205 \times 400 \times 0.72} = \frac{75000}{498.83} \approx 150.35\text{ A} I L 1 = 3 ⋅ V L ⋅ cos ϕ 1 P ⋅ 1000 = 1.73205 × 400 × 0.72 75000 = 498.83 75000 ≈ 150.35 A
Calculate Initial Reactive Power ( Q 1 Q_1 Q 1 ): ϕ 1 = arccos ( 0.72 ) = 43.95 ∘ \phi_1 = \arccos(0.72) = 43.95^\circ ϕ 1 = arccos ( 0.72 ) = 43.9 5 ∘ tan ϕ 1 = tan ( 43.95 ∘ ) ≈ 0.9639 \tan\phi_1 = \tan(43.95^\circ) \approx 0.9639 tan ϕ 1 = tan ( 43.9 5 ∘ ) ≈ 0.9639 Q 1 = P ⋅ tan ϕ 1 = 75 kW × 0.9639 = 72.29 kvar Q_1 = P \cdot \tan\phi_1 = 75\text{ kW} \times 0.9639 = 72.29\text{ kvar} Q 1 = P ⋅ tan ϕ 1 = 75 kW × 0.9639 = 72.29 kvar
Worked Example 6.1B: Sizing APFC Capacitor Bank to Meet DEWA Standard
Problem Statement: Using the 75 kW chiller load from Example 6.1A, calculate the required rating ( Q c Q_c Q c ) of the APFC capacitor bank in kvar necessary to raise the power factor to a chosen 0.97 lagging design target within DEWA's allowable range. Also, calculate the new line current ( I L 2 I_{L2} I L 2 ) after correction and the current reduction achieved.
Solution Step-by-Step:
Determine Target Angles and Tangents:
Initial cos ϕ 1 = 0.72 ⟹ tan ϕ 1 = 0.9639 \cos\phi_1 = 0.72 \implies \tan\phi_1 = 0.9639 cos ϕ 1 = 0.72 ⟹ tan ϕ 1 = 0.9639 .
Target cos ϕ 2 = 0.97 ⟹ ϕ 2 = arccos ( 0.97 ) = 14.07 ∘ ⟹ tan ϕ 2 = tan ( 14.07 ∘ ) = 0.2506 \cos\phi_2 = 0.97 \implies \phi_2 = \arccos(0.97) = 14.07^\circ \implies \tan\phi_2 = \tan(14.07^\circ) = 0.2506 cos ϕ 2 = 0.97 ⟹ ϕ 2 = arccos ( 0.97 ) = 14.0 7 ∘ ⟹ tan ϕ 2 = tan ( 14.0 7 ∘ ) = 0.2506 .
Calculate Required Capacitor Rating ( Q c Q_c Q c ): Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 ) = 75 × ( 0.9639 − 0.2506 ) = 75 × 0.7133 = 53.50 kvar Q_c = P \cdot (\tan\phi_1 - \tan\phi_2) = 75 \times (0.9639 - 0.2506) = 75 \times 0.7133 = 53.50\text{ kvar} Q c = P ⋅ ( tan ϕ 1 − tan ϕ 2 ) = 75 × ( 0.9639 − 0.2506 ) = 75 × 0.7133 = 53.50 kvar
(Note: The contractor would specify a standard 55 kvar APFC capacitor step).
Calculate Corrected Line Current ( I L 2 I_{L2} I L 2 ): I L 2 = P ⋅ 1000 3 ⋅ V L ⋅ cos ϕ 2 = 75000 1.73205 × 400 × 0.97 = 75000 672.04 ≈ 111.60 A I_{L2} = \frac{P \cdot 1000}{\sqrt{3} \cdot V_L \cdot \cos\phi_2} = \frac{75000}{1.73205 \times 400 \times 0.97} = \frac{75000}{672.04} \approx 111.60\text{ A} I L 2 = 3 ⋅ V L ⋅ cos ϕ 2 P ⋅ 1000 = 1.73205 × 400 × 0.97 75000 = 672.04 75000 ≈ 111.60 A
Calculate Current Reduction: Δ I = I L 1 − I L 2 = 150.35 A − 111.60 A = 38.75 A \Delta I = I_{L1} - I_{L2} = 150.35\text{ A} - 111.60\text{ A} = 38.75\text{ A} Δ I = I L 1 − I L 2 = 150.35 A − 111.60 A = 38.75 A Percentage Reduction = 38.75 150.35 × 100 % ≈ 25.77 % \text{Percentage Reduction} = \frac{38.75}{150.35} \times 100\% \approx 25.77\% Percentage Reduction = 150.35 38.75 × 100% ≈ 25.77%
Study takeaway: Power factor correction from 0.72 to 0.97 reduces the cable current by 25.77% , freeing up switchgear thermal headroom and reducing reactive demand.