Study guide

1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them

Alaska Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Alaska Certificates of Fitness, Law & Exam Logistics

1.1 The Alaska Certificate of Fitness System 1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them 1.3 Trainee, Residential Wireman, Lineman, Provisional & Reciprocal Certificates 1.4 The Journeyman Examination: Format, Scheduling, Open-Book Rules & Retakes 1.5 Adopted Codes, Fees, Renewal, Inspection & Enforcement

2 Chapter 2: Using the 2020 NEC

2.1 Article 90: Purpose, Scope, Arrangement & Enforcement 2.2 Navigating the Code Book: Structure, Index & Tabbing Strategy 2.3 Article 100 Definitions You Must Know Cold 2.4 Electrical Theory for the Exam: Ohm's Law, Power & Three-Phase

3 Chapter 3: General Requirements — Article 110

3.1 Approval, Listing, Interrupting Rating & Terminations 3.2 Temperature Limitations of Terminations — 110.14(C) 3.3 Working Space, Access, Egress & Illumination — 110.26(A) through (D) 3.4 Dedicated Equipment Space, Guarding & Over-1000-Volt Installations

4 Chapter 4: Conductors and Ampacity — Article 310

4.1 Conductor Types, Insulation Markings & Table 310.16 4.2 Ambient Temperature Correction and Alaska's Cold 4.3 Adjustment for More Than Three Current-Carrying Conductors 4.4 Putting It Together: Full Conductor-Sizing Problems 4.5 Parallel Conductors, Dwelling Service Sizing & Conditions of Use

5 Chapter 5: Wiring Methods and Materials — NEC Chapter 3

5.1 Article 300 General Requirements and Underground Cover 5.2 Thermal Movement: Expansion Fittings and Table 352.44 5.3 Boxes and Enclosures: Box Fill and Pull Box Sizing 5.4 Cable Assemblies: NM, MC, AC, SE, UF and TC 5.5 Raceways: RMC, IMC, EMT, FMC, LFMC, PVC and ENT 5.6 Conduit Fill: Chapter 9 Tables and Annex C 5.7 Cable Trays, Wireways, Busways, Gutters and Surface Raceways

6 Chapter 6: Branch Circuits and Feeders

6.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Circuits 6.2 Required Outlets and Receptacle Spacing in Dwellings 6.3 GFCI Protection — Article 210.8 6.4 AFCI Protection and Receptacle Requirements 6.5 Feeders and Outside Branch Circuits — Articles 215 and 225 6.6 Grounded Conductor Identification, Switches & Panelboards

7 Chapter 7: Overcurrent Protection — Articles 240 and 242

7.1 Article 240 Fundamentals: Ratings, Locations & Conductor Protection 7.2 Feeder Tap Rules — 240.21(B) 7.3 Transformer Secondary Conductors — 240.21(C) 7.4 Fuses, Circuit Breakers, Series Ratings & Article 242 Surge Protection

8 Chapter 8: Services and Load Calculations

8.1 Service Conductors, Clearances and Service Equipment 8.2 Service Disconnects, the 2020 Rule Change, SPDs and Service GFPE 8.3 Article 220 Part II: General Lighting, Receptacles and Demand Factors 8.4 The Standard Dwelling Calculation — Article 220 Part III 8.5 Optional Dwelling and Multifamily Calculations 8.6 Commercial and Industrial Load Calculations 8.7 Neutral Load Calculations and Harmonics — 220.61

9 Chapter 9: Grounding and Bonding — Article 250

9.1 System Grounding, 250.24 and the Main Bonding Jumper 9.2 The Grounding Electrode System — 250.50 through 250.53 9.3 Grounding Electrode Conductor Sizing and Installation 9.4 Bonding: Services, Metal Piping, Structural Metal and Other Systems 9.5 Equipment Grounding Conductors: Types, Sizing and Continuity 9.6 Separately Derived Systems and Separate Buildings 9.7 Ground-Fault Protection of Equipment and Grounding of Specific Equipment

10 Chapter 10: Equipment for General Use — NEC Chapter 4

10.1 Flexible Cords, Cables and Fixture Wires 10.2 Switches, Receptacles and Industrial Control Panels 10.3 Luminaires, Lampholders and Recessed Installations 10.4 Appliances and Fixed Electric Space Heating 10.5 Deicing, Snow Melting, Pipeline and Vessel Heating 10.6 Motors Part I: Full-Load Current, Conductors and Overload Protection 10.7 Motors Part II: Short-Circuit Protection, Controllers, Disconnects and HVAC

11 Chapter 11: Transformers, Generators and Special Occupancies

11.1 Transformers — Article 450 11.2 Generators, Storage Batteries and Energy Storage Systems 11.3 Hazardous (Classified) Locations — Articles 500 through 506 11.4 Garages, Hangars, Fuel Dispensing, Bulk Storage and Spray Application 11.5 Health Care Facilities — Article 517 11.6 Agricultural Buildings, Manufactured Homes, RV Parks and Marinas 11.7 Assembly, Theaters, Carnivals, Temporary Installations and Pools

12 Chapter 12: Special Equipment, Special Conditions and Exam Strategy

12.1 Signs, Cranes, Elevators, Electric Vehicle Charging and Welders 12.2 Solar Photovoltaic, Interconnection and Stand-Alone Systems 12.3 Wind Electric Systems and Fire Pumps 12.4 Emergency, Legally Required Standby, Optional Standby and COPS 12.5 Class 1, 2 and 3 Circuits, Fire Alarm, Optical Fiber and Communications 12.6 Cold-Climate Practice in Alaska: Code Basis and Engineering Judgment 12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management

1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them

Key Takeaways Explain This Topic AI

8 AAC 90.160(b)(2) requires 8,000 hours of work experience subject to NEC standards, documented on a notarized department form, notarized employer letterhead statements, or a sworn Alaska-union affidavit.

The department counts no more than 2,000 hours of residential electrical work toward the 8,000-hour total under 8 AAC 90.160(c).

Classroom hours from a USDOL-registered apprenticeship or an accredited electrical training program substitute for a maximum of 1,000 hours under 8 AAC 90.160(d).

Up to 1,000 hours of power lineman experience may be applied under 8 AAC 90.160(e), but experience as a maintenance electrician may not be used at all under 8 AAC 90.160(f).

8 AAC 90.890 counts hours only when worked for a properly credentialed contractor, under the direct supervision of a journeyman, and in compliance with the law of the state where the work was performed.

Last updated: August 2026

The Core Requirement

8 AAC 90.160(b) says an electrician journeyman certificate of fitness will be issued on payment of the fees required by AS 18.62.030 if the applicant (1) has passed an examination meeting 8 AAC 90.115 and (2) documents a minimum of 8,000 hours of work experience subject to the standards of the National Electrical Code .

Eight thousand hours is nominally four years of full-time work. But Alaska does not accept raw hours — it accepts qualifying hours, and the qualifiers are where applications fail.

Documentation: Two Accepted Routes

8 AAC 90.160(b)(2) accepts exactly two forms of proof:

(A) Employer documentation. A notarized form provided by the department, or notarized statements on employer letterhead, showing at least 8,000 hours of NEC-covered work. In practice this is the department's Experience Verification Form (EVF) .

(B) Union affidavit. A sworn affidavit from an official of an Alaska-based union, on a department form, that demonstrates the applicant meets the requirement. The affidavit must specify the number of qualifying hours claimed, the inclusive dates worked, and the type of work performed with the name of each contractor.

The statutory hook for the union route is AS 18.62.050(c) , which permits union verification of a member's qualification in lieu of examination or other requirement. The department advises having the employer complete an EVF every six months or at the end of each period of employment and keeping the originals — reconstructing a decade of hours from a defunct employer is the single most common cause of a rejected packet.

What Makes an Hour Count — 8 AAC 90.890

8 AAC 90.890(a) sets three simultaneous conditions. Work is legally performed, and experience legally obtained, only if the work was performed:

for a contractor holding a current, valid credential required for that trade by the law of the state where the work was done, and performed in the state where the contractor is credentialed (if that state requires no credential, documented work is accepted);

under the direct supervision of a journeyman tradesperson ; and

in compliance with the laws of the state where the work was performed .

"Direct supervision" is defined narrowly in 8 AAC 90.900(8) : a certified journeyman is on the same job site, on the same floor, and in close and continual control of the trainee, and is responsible for the competency of the trainee's work. A journeyman two buildings away does not satisfy it.

The Four Caps and Exclusions

This table is worth memorizing exactly as written — the numbers are frequently confused with other states.

  • Rule Citation Effect on the 8,000 hours
  • Residential work cap 8 AAC 90.160(c) No more than 2,000 hours of residential electrical work may be counted

Classroom substitution 8 AAC 90.160(d) Classroom hours from a USDOL-registered apprenticeship or accredited electrical training program substitute for up to 1,000 hours

  • Power lineman experience 8 AAC 90.160(e) Up to 1,000 hours of power lineman experience may be applied
  • Maintenance electrician 8 AAC 90.160(f) Experience as a maintenance electrician may not be used at all

Read the first two rows carefully. The residential cap is a limit on a category of field work ; the classroom rule is a substitution allowance . They are different mechanisms with different numbers, and mixing them up (for example, claiming 2,000 classroom hours) will get a packet returned.

For comparison, the residential wireman certificate under 8 AAC 90.164 requires 4,000 hours and allows a classroom substitution of only 500 hours — again a different number.

Military and Vocational Hours

8 AAC 90.890(b) added a route that matters in a state with a large military population:

The department determines which military occupational specialty (MOS) or Air Force specialty codes (AFSC) qualify as hands-on trade experience, and which vocational schools qualify.

An applicant may claim up to 500 hours per full year assigned to a qualifying MOS or AFSC.

The maximum military-plus-vocational hours claimable is half the total required for the certificate — for the electrician journeyman, 4,000 hours.

Proof is a copy of the DD Form 214 or a certificate issued by the vocational training program.

Note the interaction: the half-the-total military/vocational allowance (4,000 hours) and the 1,000-hour classroom substitution in 8 AAC 90.160(d) are separate provisions with separate ceilings. When your hours involve both, submit the documentation and let Mechanical Inspection apply the caps rather than pre-computing a total that the department may score differently.

The Practical Sequence

Find an employer to sponsor you in the federal Registered Apprenticeship Program ; have them print the Davis Bacon letter from RAPIDS showing your registration.

Submit that letter with a Trainee Application to mi@alaska.gov . Expect 7–10 business days of processing; the certificate arrives by email.

Work under your trainee COF, tracking hours on EVFs signed by each employer.

At 8,000 qualifying hours, submit the journeyman application with your EVFs.

Once the packet is validated, Mechanical Inspection schedules your exam .

Pass at 70 percent or higher and the journey-level certificate is issued.

You may not perform code work while waiting for a certificate to process. You may do non-code work for your employer or study.