Study guide
2.1 Article 90: Purpose, Scope, Arrangement & Enforcement
Alaska Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Alaska Certificates of Fitness, Law & Exam Logistics
1.1 The Alaska Certificate of Fitness System 1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them 1.3 Trainee, Residential Wireman, Lineman, Provisional & Reciprocal Certificates 1.4 The Journeyman Examination: Format, Scheduling, Open-Book Rules & Retakes 1.5 Adopted Codes, Fees, Renewal, Inspection & Enforcement
2 Chapter 2: Using the 2020 NEC
2.1 Article 90: Purpose, Scope, Arrangement & Enforcement 2.2 Navigating the Code Book: Structure, Index & Tabbing Strategy 2.3 Article 100 Definitions You Must Know Cold 2.4 Electrical Theory for the Exam: Ohm's Law, Power & Three-Phase
3 Chapter 3: General Requirements — Article 110
3.1 Approval, Listing, Interrupting Rating & Terminations 3.2 Temperature Limitations of Terminations — 110.14(C) 3.3 Working Space, Access, Egress & Illumination — 110.26(A) through (D) 3.4 Dedicated Equipment Space, Guarding & Over-1000-Volt Installations
4 Chapter 4: Conductors and Ampacity — Article 310
4.1 Conductor Types, Insulation Markings & Table 310.16 4.2 Ambient Temperature Correction and Alaska's Cold 4.3 Adjustment for More Than Three Current-Carrying Conductors 4.4 Putting It Together: Full Conductor-Sizing Problems 4.5 Parallel Conductors, Dwelling Service Sizing & Conditions of Use
5 Chapter 5: Wiring Methods and Materials — NEC Chapter 3
5.1 Article 300 General Requirements and Underground Cover 5.2 Thermal Movement: Expansion Fittings and Table 352.44 5.3 Boxes and Enclosures: Box Fill and Pull Box Sizing 5.4 Cable Assemblies: NM, MC, AC, SE, UF and TC 5.5 Raceways: RMC, IMC, EMT, FMC, LFMC, PVC and ENT 5.6 Conduit Fill: Chapter 9 Tables and Annex C 5.7 Cable Trays, Wireways, Busways, Gutters and Surface Raceways
6 Chapter 6: Branch Circuits and Feeders
6.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Circuits 6.2 Required Outlets and Receptacle Spacing in Dwellings 6.3 GFCI Protection — Article 210.8 6.4 AFCI Protection and Receptacle Requirements 6.5 Feeders and Outside Branch Circuits — Articles 215 and 225 6.6 Grounded Conductor Identification, Switches & Panelboards
7 Chapter 7: Overcurrent Protection — Articles 240 and 242
7.1 Article 240 Fundamentals: Ratings, Locations & Conductor Protection 7.2 Feeder Tap Rules — 240.21(B) 7.3 Transformer Secondary Conductors — 240.21(C) 7.4 Fuses, Circuit Breakers, Series Ratings & Article 242 Surge Protection
8 Chapter 8: Services and Load Calculations
8.1 Service Conductors, Clearances and Service Equipment 8.2 Service Disconnects, the 2020 Rule Change, SPDs and Service GFPE 8.3 Article 220 Part II: General Lighting, Receptacles and Demand Factors 8.4 The Standard Dwelling Calculation — Article 220 Part III 8.5 Optional Dwelling and Multifamily Calculations 8.6 Commercial and Industrial Load Calculations 8.7 Neutral Load Calculations and Harmonics — 220.61
9 Chapter 9: Grounding and Bonding — Article 250
9.1 System Grounding, 250.24 and the Main Bonding Jumper 9.2 The Grounding Electrode System — 250.50 through 250.53 9.3 Grounding Electrode Conductor Sizing and Installation 9.4 Bonding: Services, Metal Piping, Structural Metal and Other Systems 9.5 Equipment Grounding Conductors: Types, Sizing and Continuity 9.6 Separately Derived Systems and Separate Buildings 9.7 Ground-Fault Protection of Equipment and Grounding of Specific Equipment
10 Chapter 10: Equipment for General Use — NEC Chapter 4
10.1 Flexible Cords, Cables and Fixture Wires 10.2 Switches, Receptacles and Industrial Control Panels 10.3 Luminaires, Lampholders and Recessed Installations 10.4 Appliances and Fixed Electric Space Heating 10.5 Deicing, Snow Melting, Pipeline and Vessel Heating 10.6 Motors Part I: Full-Load Current, Conductors and Overload Protection 10.7 Motors Part II: Short-Circuit Protection, Controllers, Disconnects and HVAC
11 Chapter 11: Transformers, Generators and Special Occupancies
11.1 Transformers — Article 450 11.2 Generators, Storage Batteries and Energy Storage Systems 11.3 Hazardous (Classified) Locations — Articles 500 through 506 11.4 Garages, Hangars, Fuel Dispensing, Bulk Storage and Spray Application 11.5 Health Care Facilities — Article 517 11.6 Agricultural Buildings, Manufactured Homes, RV Parks and Marinas 11.7 Assembly, Theaters, Carnivals, Temporary Installations and Pools
12 Chapter 12: Special Equipment, Special Conditions and Exam Strategy
12.1 Signs, Cranes, Elevators, Electric Vehicle Charging and Welders 12.2 Solar Photovoltaic, Interconnection and Stand-Alone Systems 12.3 Wind Electric Systems and Fire Pumps 12.4 Emergency, Legally Required Standby, Optional Standby and COPS 12.5 Class 1, 2 and 3 Circuits, Fire Alarm, Optical Fiber and Communications 12.6 Cold-Climate Practice in Alaska: Code Basis and Engineering Judgment 12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management
2.1 Article 90: Purpose, Scope, Arrangement & Enforcement
Key Takeaways Explain This Topic AI
NEC 90.1(A) states the purpose is the practical safeguarding of persons and property from hazards arising from the use of electricity; 90.1(B) adds that compliance produces an installation that is essentially free from hazard but not necessarily efficient, convenient, or adequate for future expansion.
NEC 90.2(B) excludes utility-owned installations, railway generation and signalling, ships, aircraft, mining equipment, and installations under the exclusive control of an electric utility from the Code's scope.
NEC 90.3 fixes the arrangement: Chapters 1 through 4 apply generally, Chapters 5, 6, and 7 supplement or modify them, Chapter 8 stands alone unless referenced, and Chapter 9 tables are applicable as referenced.
NEC 90.5 defines the language: 'shall' is mandatory, permissive rules use 'shall be permitted,' explanatory Informational Notes are not enforceable, and Informative Annexes are not part of the Code requirements.
NEC 90.4 makes the authority having jurisdiction responsible for interpreting rules, approving equipment, and granting special permission in writing.
Last updated: August 2026
Why Article 90 Is Tested
Candidates skip Article 90 because it looks like a preface. It is not — it is the set of meta-rules that tell you how every other article behaves. An exam question about whether Chapter 5 can override Chapter 3, or whether an Informational Note is enforceable, is answered in Article 90 and nowhere else. On an open-book exam this is cheap credit.
90.1 Purpose
90.1(A) Practical Safeguarding. "The purpose of this Code is the practical safeguarding of persons and property from hazards arising from the use of electricity." Note the qualifier: not the elimination of all risk, but practical safeguarding.
90.1(B) Adequacy. The Code contains provisions considered necessary for safety, and compliance with it "and proper maintenance results in an installation that is essentially free from hazard but not necessarily efficient, convenient, or adequate for good service or future expansion of electrical use." This sentence is a classic exam item. A Code-minimum installation is a safe installation, not necessarily a good one. Voltage-drop performance, spare capacity, and future expansion are design choices beyond the Code minimum.
90.1(C) Relation to Other International Standards. The Code addresses the fundamental principles of protection for safety in IEC 60364-1.
90.2 Scope
90.2(A) Covered. The installation of electrical conductors, equipment, and raceways; signalling and communications conductors and equipment; and optical fiber cables — for public and private premises, yards, lots, parking lots, carnivals, industrial substations, and installations of conductors and equipment that connect to the supply of electricity, plus installations used by an electric utility that are not an integral part of a generating plant, substation, or control center.
90.2(B) Not Covered. Learn this list; it produces reliable exam questions:
Installations in ships, watercraft, railway rolling stock, aircraft, or automotive vehicles (with a floating-building exception referencing Article 553);
Installations underground in mines and self-propelled mobile surface mining machinery and its attendant electrical trailing cable;
Installations of railways for generation, transformation, transmission, energy storage, or distribution of power used exclusively for operation of rolling stock, or installations used exclusively for signalling and communications purposes;
Installations of communications equipment under the exclusive control of communications utilities, in specified locations;
Installations under the exclusive control of an electric utility where they consist of service drops or laterals, are on property owned or leased by the utility, are on public highways or streets by legal right, or are for the purpose of communications, metering, generation, control, transformation, transmission, energy storage, or distribution of electric energy.
That last item is why the utility side of the meter is outside your journeyman scope and outside the NEC, matching the 8 AAC 90.900(10) definition that starts your trade at the secondary side of the transformer.
90.3 Code Arrangement — the Hierarchy That Decides Conflicts
This is the single most useful rule in Article 90:
- Chapters Status
- 1, 2, 3, 4 Apply generally to all electrical installations
- 5, 6, 7 Supplement or modify the requirements in Chapters 1 through 7
8 Communications systems — not subject to Chapters 1 through 7 except where the requirements are specifically referenced
- 9 Tables — applicable as referenced
- Informative Annexes Not part of the Code requirements ; informational only
So when Article 517 (health care) or Article 680 (pools) says something different from Article 250, the special-occupancy rule wins. When Article 800 says nothing about a Chapter 3 requirement, that Chapter 3 requirement does not automatically apply, because Chapter 8 stands alone.
90.4 Enforcement
The Code is intended to be suitable for mandatory application by governmental bodies. The authority having jurisdiction (AHJ) is responsible for interpreting the rules, deciding on the approval of equipment and materials, and — by special permission — granting waivers of specific requirements and permitting alternative methods where equivalent safety is assured.
Special permission is defined in Article 100 as the written consent of the authority having jurisdiction . Verbal approval from an inspector is not special permission. 90.4 also allows the AHJ to waive requirements or permit alternatives in existing buildings where it is assured that equivalent objectives can be achieved, and to allow use of equipment or materials not yet available at the time of adoption.
In Alaska the AHJ is generally a state electrical inspector or an authorized deputy electrical inspector appointed under AS 18.60.610 and 8 AAC 70.040, or a municipal inspector in a jurisdiction that has adopted its own not-less-stringent standards under AS 18.60.590(b).
90.5 Mandatory Rules, Permissive Rules, and Explanatory Material
Category Signal words Enforceable?
Mandatory rule "shall" or "shall not" Yes — required or prohibited
Permissive rule "shall be permitted" or "shall not be required" Yes , as an allowance — optional action or exemption
- Informational Note Explanatory material No — informational only
- Informative Annex Annex A through Annex J No — not a Code requirement
90.5(D) Informative Annexes confirms that annexes are not part of the enforceable requirements but are included for informational purposes. This is why the widely quoted 3 percent and 5 percent voltage-drop figures are recommendations : they live in Informational Notes to 210.19(A) and 215.2(A), not in mandatory text. Sizing a conductor for a 4 percent branch-circuit drop is legal; sizing it below its required ampacity is not.
90.7 Examination of Equipment for Safety explains that product-safety evaluation is generally performed by qualified electrical testing laboratories, and that the AHJ need not inspect internal wiring of listed factory-assembled equipment.
90.9 governs units of measurement, with SI units shown first and inch-pound units following in parentheses; 90.9(D) makes clear that either system may be used, and the values are not exact conversions.