Study guide
8.1 Service Conductors, Clearances and Service Equipment
Alaska Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Alaska Certificates of Fitness, Law & Exam Logistics
1.1 The Alaska Certificate of Fitness System 1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them 1.3 Trainee, Residential Wireman, Lineman, Provisional & Reciprocal Certificates 1.4 The Journeyman Examination: Format, Scheduling, Open-Book Rules & Retakes 1.5 Adopted Codes, Fees, Renewal, Inspection & Enforcement
2 Chapter 2: Using the 2020 NEC
2.1 Article 90: Purpose, Scope, Arrangement & Enforcement 2.2 Navigating the Code Book: Structure, Index & Tabbing Strategy 2.3 Article 100 Definitions You Must Know Cold 2.4 Electrical Theory for the Exam: Ohm's Law, Power & Three-Phase
3 Chapter 3: General Requirements — Article 110
3.1 Approval, Listing, Interrupting Rating & Terminations 3.2 Temperature Limitations of Terminations — 110.14(C) 3.3 Working Space, Access, Egress & Illumination — 110.26(A) through (D) 3.4 Dedicated Equipment Space, Guarding & Over-1000-Volt Installations
4 Chapter 4: Conductors and Ampacity — Article 310
4.1 Conductor Types, Insulation Markings & Table 310.16 4.2 Ambient Temperature Correction and Alaska's Cold 4.3 Adjustment for More Than Three Current-Carrying Conductors 4.4 Putting It Together: Full Conductor-Sizing Problems 4.5 Parallel Conductors, Dwelling Service Sizing & Conditions of Use
5 Chapter 5: Wiring Methods and Materials — NEC Chapter 3
5.1 Article 300 General Requirements and Underground Cover 5.2 Thermal Movement: Expansion Fittings and Table 352.44 5.3 Boxes and Enclosures: Box Fill and Pull Box Sizing 5.4 Cable Assemblies: NM, MC, AC, SE, UF and TC 5.5 Raceways: RMC, IMC, EMT, FMC, LFMC, PVC and ENT 5.6 Conduit Fill: Chapter 9 Tables and Annex C 5.7 Cable Trays, Wireways, Busways, Gutters and Surface Raceways
6 Chapter 6: Branch Circuits and Feeders
6.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Circuits 6.2 Required Outlets and Receptacle Spacing in Dwellings 6.3 GFCI Protection — Article 210.8 6.4 AFCI Protection and Receptacle Requirements 6.5 Feeders and Outside Branch Circuits — Articles 215 and 225 6.6 Grounded Conductor Identification, Switches & Panelboards
7 Chapter 7: Overcurrent Protection — Articles 240 and 242
7.1 Article 240 Fundamentals: Ratings, Locations & Conductor Protection 7.2 Feeder Tap Rules — 240.21(B) 7.3 Transformer Secondary Conductors — 240.21(C) 7.4 Fuses, Circuit Breakers, Series Ratings & Article 242 Surge Protection
8 Chapter 8: Services and Load Calculations
8.1 Service Conductors, Clearances and Service Equipment 8.2 Service Disconnects, the 2020 Rule Change, SPDs and Service GFPE 8.3 Article 220 Part II: General Lighting, Receptacles and Demand Factors 8.4 The Standard Dwelling Calculation — Article 220 Part III 8.5 Optional Dwelling and Multifamily Calculations 8.6 Commercial and Industrial Load Calculations 8.7 Neutral Load Calculations and Harmonics — 220.61
9 Chapter 9: Grounding and Bonding — Article 250
9.1 System Grounding, 250.24 and the Main Bonding Jumper 9.2 The Grounding Electrode System — 250.50 through 250.53 9.3 Grounding Electrode Conductor Sizing and Installation 9.4 Bonding: Services, Metal Piping, Structural Metal and Other Systems 9.5 Equipment Grounding Conductors: Types, Sizing and Continuity 9.6 Separately Derived Systems and Separate Buildings 9.7 Ground-Fault Protection of Equipment and Grounding of Specific Equipment
10 Chapter 10: Equipment for General Use — NEC Chapter 4
10.1 Flexible Cords, Cables and Fixture Wires 10.2 Switches, Receptacles and Industrial Control Panels 10.3 Luminaires, Lampholders and Recessed Installations 10.4 Appliances and Fixed Electric Space Heating 10.5 Deicing, Snow Melting, Pipeline and Vessel Heating 10.6 Motors Part I: Full-Load Current, Conductors and Overload Protection 10.7 Motors Part II: Short-Circuit Protection, Controllers, Disconnects and HVAC
11 Chapter 11: Transformers, Generators and Special Occupancies
11.1 Transformers — Article 450 11.2 Generators, Storage Batteries and Energy Storage Systems 11.3 Hazardous (Classified) Locations — Articles 500 through 506 11.4 Garages, Hangars, Fuel Dispensing, Bulk Storage and Spray Application 11.5 Health Care Facilities — Article 517 11.6 Agricultural Buildings, Manufactured Homes, RV Parks and Marinas 11.7 Assembly, Theaters, Carnivals, Temporary Installations and Pools
12 Chapter 12: Special Equipment, Special Conditions and Exam Strategy
12.1 Signs, Cranes, Elevators, Electric Vehicle Charging and Welders 12.2 Solar Photovoltaic, Interconnection and Stand-Alone Systems 12.3 Wind Electric Systems and Fire Pumps 12.4 Emergency, Legally Required Standby, Optional Standby and COPS 12.5 Class 1, 2 and 3 Circuits, Fire Alarm, Optical Fiber and Communications 12.6 Cold-Climate Practice in Alaska: Code Basis and Engineering Judgment 12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management
8.1 Service Conductors, Clearances and Service Equipment
Key Takeaways Explain This Topic AI
NEC 230.24(B) requires overhead service conductor clearances of 10 feet above pedestrian-only areas at not over 150 volts to ground, 12 feet over residential property and driveways at not over 300 volts to ground, 15 feet where the voltage exceeds 300 volts to ground, and 18 feet over public streets and truck-traffic areas.
NEC 230.24(A) requires 8 feet of clearance above roofs, with Exception No. 3 permitting a reduction to 18 inches above only the overhanging portion where not more than 6 feet of conductor passes above the roof, not more than 4 feet horizontally, terminating at a through-the-roof raceway or approved support.
NEC 230.9 requires service conductors to maintain 3 feet of clearance from windows designed to be opened, doors, porches, balconies, ladders, stairs, and fire escapes, except above the top level of a window.
NEC 230.2 permits only one service to a building or structure, with listed exceptions for special conditions, special occupancies, capacity requirements, different characteristics, and documented switching procedures.
NEC 230.70(A)(1) requires the service disconnecting means to be installed at a readily accessible location either outside the building or inside nearest the point of entrance of the service conductors.
Last updated: August 2026
Where the Code Starts
90.2(B)(5) excludes installations under the exclusive control of an electric utility from the NEC. Article 100 defines the service point as the point of connection between the facilities of the serving utility and the premises wiring. Everything from that point onward is yours; everything before it belongs to the utility and to the National Electrical Safety Code.
The defined terms matter and are frequently tested:
- Term Meaning
- Service conductors The conductors from the service point to the service disconnecting means
- Service drop The overhead conductors between the utility electric supply system and the service point
Overhead service conductors The overhead conductors between the service point and the first point of connection to the service-entrance conductors
Service lateral The underground conductors between the utility electric supply system and the service point
Underground service conductors The underground conductors between the service point and the first point of connection to the service-entrance conductors
Service-entrance conductors The service conductors between the terminals of the service equipment and a point outside the building, or the point of connection to the service drop, overhead service conductors, service lateral, or underground service conductors
Service equipment The necessary equipment, usually one or more circuit breakers or switches and fuses, connected to the load end of service conductors, intended to constitute the main control and cutoff of the supply
Number of Services — 230.2
A building or other structure served shall be supplied by only one service unless permitted in 230.2(A) through (D).
(A) Special Conditions. Fire pumps; emergency systems; legally required standby; optional standby; parallel power production systems; systems designed for connection to multiple sources for enhanced reliability.
(B) Special Occupancies. By special permission, multiple-occupancy buildings where there is no available space for service equipment accessible to all occupants, or a single building or structure sufficiently large to make two or more services necessary.
(C) Capacity Requirements. Where capacity requirements are in excess of 2000 amperes at a supply voltage of 1000 volts or less; where the load requirements of a single-phase installation are greater than the serving agency normally supplies through one service; or by special permission.
(D) Different Characteristics. Different voltages, frequencies, or phases, or for different uses such as different rate schedules.
230.2(E) Identification. Where a building or structure is supplied by more than one service, or any combination of branch circuits, feeders, and services, a permanent plaque or directory shall be installed at each service disconnect location denoting all other services, feeders, and branch circuits supplying that building and the area served by each.
Overhead Service Clearances — 230.24
230.24(A) Above Roofs. Conductors shall have a vertical clearance of not less than 8 feet (2.5 m) above the roof surface, maintained for a distance of not less than 3 feet in all directions from the edge of the roof.
- Exception Condition Reduced clearance
- No. 1 Area above the roof is subject to pedestrian or vehicular traffic Use the 230.24(B) clearances instead
- No. 2 Voltage between conductors does not exceed 300, and the roof slope is not less than 4 in. in 12 in. 3 ft
No. 3 Voltage between conductors does not exceed 300, and not more than 6 ft of conductor, 4 ft horizontally , passes above the roof overhang, terminating at a through-the-roof raceway or approved support 18 in. above only the overhanging portion
No. 4 The requirement for maintaining the clearance 3 ft in all directions from the edge of the roof does not apply to the final conductor span where the conductors are attached to the side of a building —
Exceptions 2 and 3 are constantly swapped. Exception No. 2 is the sloped-roof rule at 3 feet. Exception No. 3 is the roof-overhang service-mast rule at 18 inches.
230.24(B) Vertical Clearance for Overhead Service Conductors. Overhead service conductors shall have the following minimum clearance from final grade:
Clearance Condition
10 ft At the electric service entrance to buildings, at the lowest point of the drip loop, and above areas or sidewalks accessible only to pedestrians, measured from final grade or other accessible surface, only for service-drop cables supported on and cabled together with a grounded bare messenger where the voltage does not exceed 150 volts to ground
12 ft Over residential property and driveways, and those commercial areas not subject to truck traffic, where the voltage does not exceed 300 volts to ground
15 ft For those areas listed in the 12-foot classification where the voltage exceeds 300 volts to ground
18 ft Over public streets, alleys, roads, parking areas subject to truck traffic, driveways on other than residential property, and other land traversed by vehicles, such as cultivated, grazing, forest, and orchard
24.5 ft Over the track rails of railroads
Note the deliberate trap in the 12-foot row: a residential driveway is 12 feet even where the homeowner parks a pickup, because the 18-foot row applies to "driveways on other than residential property."
230.9 Clearances on Buildings. Service conductors installed as open conductors or multiconductor cable without an overall outer jacket shall have a clearance of not less than 3 feet (900 mm) from windows that are designed to be opened, doors, porches, balconies, ladders, stairs, fire escapes, or similar locations. Exception: conductors run above the top level of a window shall be permitted to be less than 3 feet.
230.9(C) Above Final Grade. Service conductors shall have a clearance of not less than 10 feet (3.0 m) above the final grade or lower level, where not readily accessible.
Service Masts — 230.28
230.28(A) Strength. Where a service mast is used for the support of overhead service conductors, it shall be of adequate strength or be supported by braces or guys to withstand safely the strain imposed by the service-drop or overhead service conductors. Hubs intended for use with a conduit that serves as a service mast shall be identified for use with service-entrance equipment.
230.28(B) Attachment. Only power service-drop or overhead service conductors shall be permitted to be attached to a service mast. Communications, CATV, and other cables may not be strapped to it.
Wiring Methods and Support — Parts IV and V
230.43 Wiring Methods for 1000 Volts, Nominal, or Less. Service-entrance conductors shall be installed in accordance with the applicable requirements of the Code covering the type of wiring method used and shall be limited to the listed methods: open wiring on insulators; Type IGS cable; rigid metal conduit; intermediate metal conduit; electrical metallic tubing; electrical nonmetallic tubing; service-entrance cables; wireways; busways; auxiliary gutters; rigid polyvinyl chloride conduit; cablebus; Type MC cable; mineral-insulated cable; flexible metal conduit or liquidtight flexible metal conduit not over 6 feet long between raceways or between raceway and service equipment with a wire-type equipment bonding jumper; liquidtight flexible nonmetallic conduit; high density polyethylene conduit; nonmetallic underground conduit with conductors; and reinforced thermosetting resin conduit.
230.50 Protection Against Physical Damage. Underground service-entrance conductors shall be protected against physical damage in accordance with 300.5. All other service-entrance conductors shall be protected where subject to physical damage.
230.51(A) Service-Entrance Cables. Service-entrance cable shall be supported by straps or other approved means within 12 inches (300 mm) of every service head, gooseneck, or connection to a raceway or enclosure and at intervals not exceeding 30 inches (750 mm) .
230.54 Overhead Service Locations.
(A) Service raceways shall be equipped with a rain-tight service head at the point of connection to service-drop or overhead service conductors.
(B) Service-entrance cables shall be equipped with a rain-tight service head, or the cable shall be formed in a gooseneck and taped with self-sealing weather-resistant thermoplastic.
(C) Service heads and goosenecks in service-entrance cables shall be located above the point of attachment of the service-drop or overhead service conductors to the building. Exception: where it is impracticable, the service head or gooseneck shall be permitted to be located not further than 24 inches (600 mm) from the point of attachment.
(F) Drip loops shall be formed on individual conductors. To prevent the entrance of moisture, service-entrance conductors shall be connected to the service-drop or overhead service conductors below the level of the service head and below the termination of the service entrance cable sheath.
(G) Service-drop conductors and service-entrance conductors shall be arranged so that water will not enter service raceway or equipment.
230.53 Raceways to Drain. Where exposed to the weather, raceways enclosing service-entrance conductors shall be raintight and arranged to drain.
Underground Service Conductors — Part III
230.30(A) requires underground service conductors to be insulated for the applied voltage, with limited exceptions for bare copper used in a raceway or for direct burial where suitable for the soil conditions, bare copper for direct burial where bare copper is judged suitable by the authority having jurisdiction, and bare copper or aluminum in cable assemblies identified for underground use.
230.32 Protection Against Damage. Underground service conductors shall be protected against damage in accordance with 300.5. Service conductors entering a building shall be installed in accordance with 230.6 or protected by a raceway wiring method identified in 230.43.
230.6 Conductors Considered Outside the Building. Conductors are considered outside a building or other structure where they are:
- Installed under not less than 2 inches (50 mm) of concrete beneath a building;
- Installed within a building in a raceway that is encased in concrete or brick not less than 2 inches thick ;
- Installed in a vault that meets the construction requirements of Article 450, Part III;
- Installed in conduit and under not less than 18 inches (450 mm) of earth beneath a building;
Installed in overhead service masts on the outside surface of the building traveling directly to the point of penetration.
This is why service conductors may run some distance "inside" a building before reaching the disconnect — encased in concrete, they are legally outside.
Service Conductor Sizing
230.42(A) requires ungrounded service-entrance conductors to have an ampacity not less than either the sum of the noncontinuous loads plus 125 percent of the continuous load , or the sum of continuous and noncontinuous loads where the assembly including overcurrent devices is listed for operation at 100 percent of its rating.
230.42(B) Specific Installations. In addition, the service-entrance conductors shall have adequate ampacity to carry the current as computed in accordance with Part III, IV, or V of Article 220.
230.42(C) Grounded Conductors. The grounded conductor shall not be smaller than the minimum size required by 250.24(C).
230.79 Rating of Service Disconnecting Means. The service disconnecting means shall have a rating not less than the calculated load:
- Installation Minimum rating
- (A) One-circuit installation 15 A
- (B) Two-circuit installations 30 A
- (C) One-family dwelling 100 A, 3-wire
- (D) All others 60 A
Remember 310.12(A) from Chapter 4 of this guide: a one-family dwelling service on a single-phase 120/240 V system rated 100 A through 400 A may have conductors sized at 83 percent of the service rating. The disconnect must still be rated at least 100 A.