Study guide

10.5 Deicing, Snow Melting, Pipeline and Vessel Heating

Alaska Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Alaska Certificates of Fitness, Law & Exam Logistics

1.1 The Alaska Certificate of Fitness System 1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them 1.3 Trainee, Residential Wireman, Lineman, Provisional & Reciprocal Certificates 1.4 The Journeyman Examination: Format, Scheduling, Open-Book Rules & Retakes 1.5 Adopted Codes, Fees, Renewal, Inspection & Enforcement

2 Chapter 2: Using the 2020 NEC

2.1 Article 90: Purpose, Scope, Arrangement & Enforcement 2.2 Navigating the Code Book: Structure, Index & Tabbing Strategy 2.3 Article 100 Definitions You Must Know Cold 2.4 Electrical Theory for the Exam: Ohm's Law, Power & Three-Phase

3 Chapter 3: General Requirements — Article 110

3.1 Approval, Listing, Interrupting Rating & Terminations 3.2 Temperature Limitations of Terminations — 110.14(C) 3.3 Working Space, Access, Egress & Illumination — 110.26(A) through (D) 3.4 Dedicated Equipment Space, Guarding & Over-1000-Volt Installations

4 Chapter 4: Conductors and Ampacity — Article 310

4.1 Conductor Types, Insulation Markings & Table 310.16 4.2 Ambient Temperature Correction and Alaska's Cold 4.3 Adjustment for More Than Three Current-Carrying Conductors 4.4 Putting It Together: Full Conductor-Sizing Problems 4.5 Parallel Conductors, Dwelling Service Sizing & Conditions of Use

5 Chapter 5: Wiring Methods and Materials — NEC Chapter 3

5.1 Article 300 General Requirements and Underground Cover 5.2 Thermal Movement: Expansion Fittings and Table 352.44 5.3 Boxes and Enclosures: Box Fill and Pull Box Sizing 5.4 Cable Assemblies: NM, MC, AC, SE, UF and TC 5.5 Raceways: RMC, IMC, EMT, FMC, LFMC, PVC and ENT 5.6 Conduit Fill: Chapter 9 Tables and Annex C 5.7 Cable Trays, Wireways, Busways, Gutters and Surface Raceways

6 Chapter 6: Branch Circuits and Feeders

6.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Circuits 6.2 Required Outlets and Receptacle Spacing in Dwellings 6.3 GFCI Protection — Article 210.8 6.4 AFCI Protection and Receptacle Requirements 6.5 Feeders and Outside Branch Circuits — Articles 215 and 225 6.6 Grounded Conductor Identification, Switches & Panelboards

7 Chapter 7: Overcurrent Protection — Articles 240 and 242

7.1 Article 240 Fundamentals: Ratings, Locations & Conductor Protection 7.2 Feeder Tap Rules — 240.21(B) 7.3 Transformer Secondary Conductors — 240.21(C) 7.4 Fuses, Circuit Breakers, Series Ratings & Article 242 Surge Protection

8 Chapter 8: Services and Load Calculations

8.1 Service Conductors, Clearances and Service Equipment 8.2 Service Disconnects, the 2020 Rule Change, SPDs and Service GFPE 8.3 Article 220 Part II: General Lighting, Receptacles and Demand Factors 8.4 The Standard Dwelling Calculation — Article 220 Part III 8.5 Optional Dwelling and Multifamily Calculations 8.6 Commercial and Industrial Load Calculations 8.7 Neutral Load Calculations and Harmonics — 220.61

9 Chapter 9: Grounding and Bonding — Article 250

9.1 System Grounding, 250.24 and the Main Bonding Jumper 9.2 The Grounding Electrode System — 250.50 through 250.53 9.3 Grounding Electrode Conductor Sizing and Installation 9.4 Bonding: Services, Metal Piping, Structural Metal and Other Systems 9.5 Equipment Grounding Conductors: Types, Sizing and Continuity 9.6 Separately Derived Systems and Separate Buildings 9.7 Ground-Fault Protection of Equipment and Grounding of Specific Equipment

10 Chapter 10: Equipment for General Use — NEC Chapter 4

10.1 Flexible Cords, Cables and Fixture Wires 10.2 Switches, Receptacles and Industrial Control Panels 10.3 Luminaires, Lampholders and Recessed Installations 10.4 Appliances and Fixed Electric Space Heating 10.5 Deicing, Snow Melting, Pipeline and Vessel Heating 10.6 Motors Part I: Full-Load Current, Conductors and Overload Protection 10.7 Motors Part II: Short-Circuit Protection, Controllers, Disconnects and HVAC

11 Chapter 11: Transformers, Generators and Special Occupancies

11.1 Transformers — Article 450 11.2 Generators, Storage Batteries and Energy Storage Systems 11.3 Hazardous (Classified) Locations — Articles 500 through 506 11.4 Garages, Hangars, Fuel Dispensing, Bulk Storage and Spray Application 11.5 Health Care Facilities — Article 517 11.6 Agricultural Buildings, Manufactured Homes, RV Parks and Marinas 11.7 Assembly, Theaters, Carnivals, Temporary Installations and Pools

12 Chapter 12: Special Equipment, Special Conditions and Exam Strategy

12.1 Signs, Cranes, Elevators, Electric Vehicle Charging and Welders 12.2 Solar Photovoltaic, Interconnection and Stand-Alone Systems 12.3 Wind Electric Systems and Fire Pumps 12.4 Emergency, Legally Required Standby, Optional Standby and COPS 12.5 Class 1, 2 and 3 Circuits, Fire Alarm, Optical Fiber and Communications 12.6 Cold-Climate Practice in Alaska: Code Basis and Engineering Judgment 12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management

10.5 Deicing, Snow Melting, Pipeline and Vessel Heating

Key Takeaways Explain This Topic AI

NEC 426.28 requires ground-fault protection of equipment for fixed outdoor electric deicing and snow-melting equipment, other than equipment employing mineral-insulated metal-sheathed cable embedded in a noncombustible medium.

NEC 427.22 requires ground-fault protection of equipment for fixed electric heating equipment for pipelines and vessels, with an exception for mineral-insulated metal-sheathed cable in industrial establishments under qualified maintenance and supervision.

NEC 426.4 and 427.4 both classify fixed outdoor deicing, snow-melting, pipeline, and vessel heating equipment as a continuous load, requiring 125 percent branch-circuit sizing.

NEC 427.13 requires caution signs or permanent markings on pipelines and vessels with electric heating equipment, at intervals not exceeding 20 feet.

The dedicated-branch-circuit exception in 210.8(A)(3) applies to snow-melting and deicing equipment supplied in accordance with 426.28, and is not a general exemption from outdoor GFCI requirements.

Last updated: August 2026

Why These Two Articles Matter in Alaska

Few jurisdictions apply Articles 426 and 427 as heavily as Alaska does. Roof and gutter deicing, ramp and walkway snow melting, freeze protection on water and fire-protection piping, and process heat tracing on fuel and glycol lines are routine work. Both articles share a structure and both hinge on ground-fault protection of equipment .

Article 426 Article 427

Scope Fixed outdoor electric deicing and snow-melting equipment Fixed electric heating equipment for pipelines and vessels

Typical application Roof and gutter cable, embedded ramp heating, walkway mats Freeze protection and process maintenance on piping and tanks

  • Continuous load 426.4 427.4
  • GFPE requirement 426.28 427.22
  • Marking 426.13 427.13
  • Article 426 — Deicing and Snow Melting

426.4 Continuous Load. Fixed outdoor electric deicing and snow-melting equipment shall be considered a continuous load . Branch-circuit conductors and the overcurrent device are therefore sized at 125 percent of the load under 210.19(A)(1) and 210.20(A).

426.10 General. Equipment for outdoor electric deicing and snow melting shall be identified as being suitable for the following: the chemical, thermal, and physical environment; and installation in accordance with the manufacturer's drawings and instructions.

426.11 Use. Equipment shall be installed in such a manner that it will be protected from physical damage.

426.12 Thermal Protection. External surfaces of outdoor electric deicing and snow-melting equipment that operate at temperatures exceeding 60 degrees C (140 degrees F) shall be physically guarded, isolated, or thermally insulated to protect against contact by personnel in the area.

426.13 Identification. The presence of electric deicing and snow-melting equipment shall be evident by the posting of appropriate caution signs or markings where clearly visible.

426.14 Special Permission. Fixed electric deicing and snow-melting equipment for other than these described uses shall be permitted only by special permission.

426.20 Embedded Deicing and Snow-Melting Equipment. (A) Heating element assemblies shall be installed on a substantial asphalt or masonry base at least 2 inches (50 mm) thick and have at least 1.5 inches of asphalt or masonry applied over the units; or they shall be permitted to be installed over the top of existing asphalt or masonry, provided they are covered with at least 1.5 inches of asphalt or masonry. (B) Units shall be secured in place while the masonry or asphalt finish is applied. (C) Where installed in concrete, cinder fill, or other permanent forms of construction, the units shall not be subject to physical damage. (D) Units shall be installed to provide effective heat transfer to the area to be heated. (E) Cables shall be spaced not closer than 1 inch (25 mm) on centers, providing not more than 120 watts per square foot of heated area. (F) Cables shall not cross over themselves .

426.21 Heating Cable Installation. Cables shall be installed in accordance with the manufacturer's instructions and 426.20 through 426.24.

426.22 Resistance Heating Elements and 426.23 Nonheating Leads cover terminations and lead installation. 426.24 Electrical Connection requires nonheating leads to be attached to the cable using a factory-assembled splice.

The Key Rule — 426.28

426.28 Ground-Fault Protection of Equipment. Ground-fault protection of equipment shall be provided for fixed outdoor electric deicing and snow-melting equipment, other than equipment that employs mineral-insulated, metal-sheathed cable embedded in a noncombustible medium .

Read this precisely. It requires ground-fault protection of equipment (GFPE) — not a Class A GFCI. GFPE devices are typically listed at a 30-milliampere trip level for heating applications, which is far above the 4-to-6-milliampere Class A range but far below a conventional overcurrent device. The distinction is deliberate: a long heat-trace circuit inherently leaks more than 6 milliamperes, and requiring a Class A device would produce constant nuisance tripping while a GFPE device still catches the sheath damage that starts fires.

The exception is narrow: mineral-insulated metal-sheathed cable embedded in a noncombustible medium.

210.8(A)(3) Exception ties back to this: the outdoor GFCI requirement for dwelling receptacles has an exception for receptacles supplying only snow-melting or deicing equipment on a dedicated branch circuit installed in accordance with Part III of Article 426 . That exception is specific — it does not exempt general-purpose outdoor receptacles, and it does not exempt engine block heater outlets.

426.50 Disconnecting Means. All fixed outdoor deicing and snow-melting equipment shall be provided with a means for simultaneous disconnection from all ungrounded conductors . Where readily accessible to the user of the equipment, the branch-circuit switch or circuit breaker shall be permitted to serve as the disconnecting means. The disconnecting means shall be of the indicating type and be provided with a positive lockout in the off position.

426.51 requires controllers and thermostats to be either rated for the load or have a horsepower rating, and to be marked.

Article 427 — Pipeline and Vessel Heating

427.4 Continuous Load. Fixed electric heating equipment for pipelines and vessels shall be considered a continuous load .

427.10 General. Equipment shall be identified as suitable for the chemical, thermal, and physical environment, and installed in accordance with the manufacturer's drawings and instructions.

427.12 Thermal Protection. External surfaces that operate at temperatures exceeding 60 degrees C (140 degrees F) shall be physically guarded, isolated, or thermally insulated to protect against contact by personnel in the area.

427.13 Identification. The presence of electrically heated pipelines, vessels, or both, shall be evident by the posting of appropriate caution signs or markings at intervals not exceeding 6 m (20 ft) along the pipeline or vessel and on or adjacent to equipment in the piping system that requires periodic servicing.

The 20-foot interval is a specific, tested number.

427.14 Corrosion Protection. Ferrous and nonferrous metal raceways, cable armor, cable sheath, boxes, cable trays, cabinets, elbows, couplings, nipples, fittings, supports, and support hardware shall be permitted to be installed in concrete or in direct contact with the earth, or in areas subject to severe corrosive influences, where made of material judged suitable for the condition, or where provided with corrosion protection approved for the condition.

427.15 Not Permitted in Hoistways. Pipeline and vessel heating equipment shall not be installed in hoistways.

427.16 Equipment Grounding. All fixed electric heating equipment for pipelines and vessels shall be grounded as required by Article 250.

Part IV — Impedance Heating

427.25 Personnel Protection. All accessible external surfaces of the pipeline or vessel being heated shall be physically guarded, isolated, or thermally insulated with a weatherproof jacket to protect against contact by personnel.

427.26 Isolation Transformer. A dual-winding transformer with a grounded shield between the primary and secondary windings shall be used to isolate the distribution system from the heating system.

427.28 Voltage Limitations. The secondary winding of the isolation transformer connected to the pipeline being heated shall not have an output voltage greater than 30 volts AC . Where the voltage exceeds 30 volts, ground-fault protection of equipment shall be provided.

The Key Rule — 427.22

427.22 Equipment Protection. Ground-fault protection of equipment shall be provided for electric heating equipment. Exception: In industrial establishments where there is alternating current equipment ground-fault protection and continued circuit operation is necessary for safe operation of equipment or processes, and where only qualified persons will service the installed systems, and continuous circuit operation is necessary for safe operation of equipment or processes.

Again, GFPE — not a Class A GFCI.

427.55 Disconnecting Means. All fixed electric pipeline or vessel heating equipment shall be provided with a means for disconnection from all ungrounded conductors . Where readily accessible to the user, the branch-circuit switch or circuit breaker shall be permitted. The disconnecting means shall be of the indicating type and be provided with a positive lockout in the off position.

427.57 Controllers. Each heating system shall be provided with an approved means for setting the maintenance temperature.

Practical Alaska Considerations

Nuisance tripping. Heat trace failures usually appear first as increasing leakage current. A GFPE device that trips intermittently is reporting a real problem, most often moisture ingress at a splice, a cold-lead termination, or a cable crushed by insulation cladding. Replacing the GFPE device with a plain breaker to "solve" the tripping is both a Code violation and a fire cause.

Cold-start inrush. Self-regulating heating cable draws several times its steady-state current at low temperature because the conductive polymer core's resistance falls as temperature falls. Manufacturers publish start-up current curves; the branch-circuit device must accommodate the start-up current without nuisance tripping while still satisfying 426.4 and 427.4 continuous-load sizing at 125 percent of steady-state load. This is a design calculation that comes from the manufacturer's data, made enforceable through 110.3(B) .

Roof and gutter cable. Article 426 applies. The equipment must be identified as suitable for the environment (426.10), guarded or insulated where surfaces exceed 60 degrees C (426.12), marked with caution signs (426.13), supplied at 125 percent (426.4), and protected by GFPE (426.28), with a lockable, indicating disconnect (426.50).

Buried ramp heating. Article 426 Part II applies: an asphalt or masonry base at least 2 inches thick, 1.5 inches of cover, cables secured while the finish is applied, spacing not closer than 1 inch on centers, not more than 120 watts per square foot, and no crossing of cables.