Study guide
12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management
Alaska Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Alaska Certificates of Fitness, Law & Exam Logistics
1.1 The Alaska Certificate of Fitness System 1.2 Journeyman Eligibility: 8,000 Hours and How Alaska Counts Them 1.3 Trainee, Residential Wireman, Lineman, Provisional & Reciprocal Certificates 1.4 The Journeyman Examination: Format, Scheduling, Open-Book Rules & Retakes 1.5 Adopted Codes, Fees, Renewal, Inspection & Enforcement
2 Chapter 2: Using the 2020 NEC
2.1 Article 90: Purpose, Scope, Arrangement & Enforcement 2.2 Navigating the Code Book: Structure, Index & Tabbing Strategy 2.3 Article 100 Definitions You Must Know Cold 2.4 Electrical Theory for the Exam: Ohm's Law, Power & Three-Phase
3 Chapter 3: General Requirements — Article 110
3.1 Approval, Listing, Interrupting Rating & Terminations 3.2 Temperature Limitations of Terminations — 110.14(C) 3.3 Working Space, Access, Egress & Illumination — 110.26(A) through (D) 3.4 Dedicated Equipment Space, Guarding & Over-1000-Volt Installations
4 Chapter 4: Conductors and Ampacity — Article 310
4.1 Conductor Types, Insulation Markings & Table 310.16 4.2 Ambient Temperature Correction and Alaska's Cold 4.3 Adjustment for More Than Three Current-Carrying Conductors 4.4 Putting It Together: Full Conductor-Sizing Problems 4.5 Parallel Conductors, Dwelling Service Sizing & Conditions of Use
5 Chapter 5: Wiring Methods and Materials — NEC Chapter 3
5.1 Article 300 General Requirements and Underground Cover 5.2 Thermal Movement: Expansion Fittings and Table 352.44 5.3 Boxes and Enclosures: Box Fill and Pull Box Sizing 5.4 Cable Assemblies: NM, MC, AC, SE, UF and TC 5.5 Raceways: RMC, IMC, EMT, FMC, LFMC, PVC and ENT 5.6 Conduit Fill: Chapter 9 Tables and Annex C 5.7 Cable Trays, Wireways, Busways, Gutters and Surface Raceways
6 Chapter 6: Branch Circuits and Feeders
6.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Circuits 6.2 Required Outlets and Receptacle Spacing in Dwellings 6.3 GFCI Protection — Article 210.8 6.4 AFCI Protection and Receptacle Requirements 6.5 Feeders and Outside Branch Circuits — Articles 215 and 225 6.6 Grounded Conductor Identification, Switches & Panelboards
7 Chapter 7: Overcurrent Protection — Articles 240 and 242
7.1 Article 240 Fundamentals: Ratings, Locations & Conductor Protection 7.2 Feeder Tap Rules — 240.21(B) 7.3 Transformer Secondary Conductors — 240.21(C) 7.4 Fuses, Circuit Breakers, Series Ratings & Article 242 Surge Protection
8 Chapter 8: Services and Load Calculations
8.1 Service Conductors, Clearances and Service Equipment 8.2 Service Disconnects, the 2020 Rule Change, SPDs and Service GFPE 8.3 Article 220 Part II: General Lighting, Receptacles and Demand Factors 8.4 The Standard Dwelling Calculation — Article 220 Part III 8.5 Optional Dwelling and Multifamily Calculations 8.6 Commercial and Industrial Load Calculations 8.7 Neutral Load Calculations and Harmonics — 220.61
9 Chapter 9: Grounding and Bonding — Article 250
9.1 System Grounding, 250.24 and the Main Bonding Jumper 9.2 The Grounding Electrode System — 250.50 through 250.53 9.3 Grounding Electrode Conductor Sizing and Installation 9.4 Bonding: Services, Metal Piping, Structural Metal and Other Systems 9.5 Equipment Grounding Conductors: Types, Sizing and Continuity 9.6 Separately Derived Systems and Separate Buildings 9.7 Ground-Fault Protection of Equipment and Grounding of Specific Equipment
10 Chapter 10: Equipment for General Use — NEC Chapter 4
10.1 Flexible Cords, Cables and Fixture Wires 10.2 Switches, Receptacles and Industrial Control Panels 10.3 Luminaires, Lampholders and Recessed Installations 10.4 Appliances and Fixed Electric Space Heating 10.5 Deicing, Snow Melting, Pipeline and Vessel Heating 10.6 Motors Part I: Full-Load Current, Conductors and Overload Protection 10.7 Motors Part II: Short-Circuit Protection, Controllers, Disconnects and HVAC
11 Chapter 11: Transformers, Generators and Special Occupancies
11.1 Transformers — Article 450 11.2 Generators, Storage Batteries and Energy Storage Systems 11.3 Hazardous (Classified) Locations — Articles 500 through 506 11.4 Garages, Hangars, Fuel Dispensing, Bulk Storage and Spray Application 11.5 Health Care Facilities — Article 517 11.6 Agricultural Buildings, Manufactured Homes, RV Parks and Marinas 11.7 Assembly, Theaters, Carnivals, Temporary Installations and Pools
12 Chapter 12: Special Equipment, Special Conditions and Exam Strategy
12.1 Signs, Cranes, Elevators, Electric Vehicle Charging and Welders 12.2 Solar Photovoltaic, Interconnection and Stand-Alone Systems 12.3 Wind Electric Systems and Fire Pumps 12.4 Emergency, Legally Required Standby, Optional Standby and COPS 12.5 Class 1, 2 and 3 Circuits, Fire Alarm, Optical Fiber and Communications 12.6 Cold-Climate Practice in Alaska: Code Basis and Engineering Judgment 12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management
12.7 Exam-Day Strategy: Navigation, Calculation Workflow and Time Management
Key Takeaways Explain This Topic AI
The Alaska electrician journeyman exam is open book with a four-hour maximum time limit, requires 70 percent to pass, and permits only the 2020 National Electrical Code as reference material.
Application processing takes 7 to 10 business days before an exam is scheduled, department testing runs on the first and third Wednesday of each month in Anchorage, Juneau, and Fairbanks, and a government-issued photo ID is required.
A failed exam requires a 30-day wait before retesting under 8 AAC 90.115(d), so a wasted attempt costs a month.
Alaska publishes no question count and no weighted content outline for this exam, so preparation should cover the whole adopted 2020 NEC rather than target a supposed blueprint.
The highest-value preparation for an open-book code exam is lookup speed: a disciplined tab system, familiarity with the article tables of contents, and repeated practice locating the calculation tables.
Last updated: August 2026
The Format, One More Time
- Item Rule Source
- Administered by Alaska DOL Mechanical Inspection Section 8 AAC 90.115(a)
Locations Division offices in Anchorage, Juneau, Fairbanks; DOL job centers by proctor; Alaska-based union halls MI Testing Information
- Schedule Department testing on the first and third Wednesday of each month MI Testing Information
- Prerequisite Approved application packet; 7 to 10 business days processing MI Testing Information
- Format Open book MI Testing Information
- Reference permitted National Electrical Code 2020 MI Testing Information
- Time limit Four (4) hours maximum MI Testing Information
- Passing score 70 percent 8 AAC 90.115(c)
- Retake wait 30 days from the failed exam 8 AAC 90.115(d)
- ID Government-issued picture ID required at testing MI Testing Information
- Results Emailed; allow 5 to 7 working days outside Anchorage MI Testing Information
Question count and content weighting are not published. Any source stating a precise number of items for this exam is not quoting the State of Alaska. Prepare for the whole 2020 NEC.
Before Test Day
Confirm the book rules. Your exam may be administered at a division office, a job center, an approved proctor, or a union hall, and the person proctoring will inspect your code book. Contact the Anchorage office and ask specifically about removable tabs, highlighting, handwritten margin notes, and loose inserted sheets . Loose paper is the item most commonly refused. Do not discover this at 8:00 a.m. on the first Wednesday of the month.
Buy the right edition. The 2020 NEC. Not the 2017 and not the 2023. Table numbering changed between 2017 and 2020 — what was Table 310.15(B)(16) is now Table 310.16 , and the ambient correction and adjustment tables are now 310.15(B)(1) and 310.15(C)(1) . A 2017 book will send you to the wrong page under time pressure.
Tab it yourself. Section 2.2 of this guide gives the three-tier system: nine chapter tabs on the top edge, about twenty high-traffic article tabs on the side, and about fifteen table tabs on the bottom in a distinct colour. Forty to sixty tabs total. Writing them yourself is part of the learning; a preprinted set will not match how you think.
Practise the lookups, not just the answers. Time yourself finding Table 220.55, Table 250.122, Table 430.52, Chapter 9 Table 4, and Annex C Table C.1 from a closed book. Under twenty seconds each is the target.
Triage: The First Pass
With four hours and no published item count, budget by proportion rather than by minutes per question. A workable approach:
Pass 1 — the sweep (about 40 percent of your time). Go through every question in order. Answer immediately anything you know cold or can look up in under thirty seconds. Mark and skip anything that requires a multi-step calculation or a lookup you are unsure of. Do not let a single hard question eat ten minutes on the first pass.
Pass 2 — the calculations (about 40 percent). Return to the marked calculation questions. These are worth the same as the easy ones, but they take five times as long, so they belong after you have banked every quick mark.
Pass 3 — the residue and review (about 20 percent). Attack anything still unanswered. Then re-read the questions you flagged as uncertain. Answer every question — an unanswered question scores zero, while a reasoned elimination gives you a real chance.
The Calculation Workflow
Every calculation question in this guide follows one of a small number of shapes. Run the same steps every time: CONDUCTOR SIZING
- 1 Load in amperes
- 2 x 1.25 for the continuous portion 210.19(A)(1) / 215.2(A)(1)
- 3 Pick a size; start at the conductor's own insulation column
- 4 x correction (310.15(B)(1)) x adjustment (310.15(C)(1))
- 5 Cap at the termination column 110.14(C)
- 6 Check the overcurrent device 240.4, 240.6(A)
- MOTOR CIRCUIT
- 1 Table FLC from 430.247-430.250 430.6(A)(1)
- 2 Conductors at 125% of table FLC 430.22
- 3 Overload at 115% or 125% of NAMEPLATE FLA 430.32(A)(1)
- 4 Short-circuit/ground-fault from Table 430.52, round UP if needed
- 5 Disconnect at 115% of table FLC 430.110(A)
- DWELLING SERVICE, STANDARD METHOD
- 1 3 VA/ft2 + 1500 VA per small-appliance and laundry circuit
- 2 Table 220.42 demand: first 3000 at 100%, remainder at 35%
- 3 Fixed appliances: 75% if four or more 220.53
- 4 Dryer: larger of 5000 VA or nameplate 220.54
- 5 Range: Table 220.55 Column C (+5%/kW over 12)
- 6 Heat or A/C, larger only 220.51 / 220.60
- 7 Total VA / 240 V = service amperes
- CONDUIT FILL
- 1 Table 5 area per conductor x quantity (include the EGC)
- 2 Sum
- 3 Table 4, the correct raceway type, 40% column (or 60% for a nipple)
- BOX FILL
- 1 Conductors entering/passing: 1 volume each, Table 314.16(B)
- 2 All EGCs together: 1 volume, largest EGC
- 3 All internal clamps together: 1 volume, largest conductor
- 4 Each device yoke: 2 volumes, largest conductor on the yoke
- 5 Pigtails: 0
Write the steps down on your scratch paper. Under time pressure, the failure mode is skipping a step, not doing arithmetic wrong.
Reading Questions Carefully
Code exams are precise. Slow down on these words:
- Phrase What it changes
- "Minimum" versus "maximum" Reverses which way you round
- "Conductor ampacity" versus "overcurrent device" Two different answers from two different rules
- "Table full-load current" versus "nameplate" Article 430 uses each in different places
- "Dwelling unit" versus "other than dwelling" Changes demand factors, GFCI scope, and receptacle rules
- "Continuous load" Adds the 125 percent multiplier
- "Voltage to ground" versus "voltage between conductors" Changes Table 110.26(A)(1), 210.8, 215.10, 230.95
- "Readily accessible" versus "accessible" Different Article 100 definitions
- "Shall be permitted" A permissive rule, not a requirement
- "Not more than" Round down to the next standard size
- The Highest-Value Traps to Rehearse
The 90 degrees C column is a starting point, never an allowable ampacity where terminations are rated lower. 110.14(C).
240.4(D) is not an ampacity. 12 AWG copper is 20 A at 60 degrees C, 25 A at 75 degrees C and 30 A at 90 degrees C, but 240.4(D)(5) caps the overcurrent device at 20 A whichever column the terminations permit.
Article 430 uses the table FLC for everything except overload , which uses nameplate.
430.62 rounds down while 240.4(B) rounds up.
The equipment grounding conductor counts for conduit fill but never for ampacity adjustment.
The neutral counts as a current-carrying conductor on a four-wire wye with major nonlinear load, and on two-phases-plus-neutral of a wye — not on a three-wire single-phase circuit.
250.66(A), (B), and (C) cap the grounding electrode conductor at 6 AWG for rods, 4 AWG for concrete-encased, and the ring conductor size for a ground ring, no matter how large the service.
Table 110.26(A)(1) is indexed on voltage to ground , and concrete, brick, or tile walls make the space Condition 2.
110.26(C)(2) is 1200 A and over 6 ft wide for two entrances; 110.26(C)(3) is 800 A within 25 ft for panic hardware. Different thresholds.
Dedicated equipment space (110.26(E)) is a column above the gear ; working space (110.26(A)) is in front of it.
The 25-ohm rule applies to a single rod, pipe, or plate electrode only. There is no maximum resistance for the system.
A water pipe electrode always needs a supplement , with no resistance exception.
The service neutral has two minimums — the 220.61 calculated load and the 250.24(C) / Table 250.102(C)(1) floor. Take the larger.
Chapter 8 stands alone under 90.3.
Informational Notes are not enforceable under 90.5(C) — including the 3 percent and 5 percent voltage-drop figures.
Alaska-Specific Facts Worth Having Cold
8 AAC 70.025 adopts the 2020 NEC and the 2017 NESC . No state technical amendments.
8,000 hours for journeyman; no more than 2,000 residential; no more than 1,000 classroom substitution; no more than 1,000 lineman; maintenance electrician does not count .
Residential wireman: 4,000 hours, 500 hours classroom , limited to four residential units on a common foundation .
Trainee ratio: two trainees per journeyman or residential wireman.
Fees: $50 application + $200 journeyman certificate for two years. Provisional is $150 total , one year, non-renewable.
Renewal: 16 hours CE, at least 8 on NEC changes , within the preceding 24 months. Renew up to 90 days early.
Penalty: AS 18.62.080 — misdemeanor, fine not more than $500 . AS 18.60.650 — up to $1,000 for non-compliant wiring left uncorrected after written notice.
Alaska issues no master electrician license. Electrical Administrator is a separate DCCED credential under AS 08.40 and does not authorize code work.
The journeyman scope begins at the secondary side of the transformer , within property lines (8 AAC 90.900(10)).
Two Weeks Out
Work the practice questions in this guide closed book first , then look up every one you missed and tab the page .
Do a full timed dwelling service calculation by both the standard and optional methods until each takes under ten minutes.
Do five conduit fill problems with mixed conductor sizes, and five with same-size conductors using Annex C.
Do five motor problems end to end: conductors, overload, short-circuit protection, feeder, disconnect.
Re-read Article 90 and the Article 100 definitions in this guide's sections 2.1 and 2.3. They are free marks.
Re-read Chapter 1 of this guide. Alaska licensing facts are the questions nobody studies and everybody could answer.
On the Day
Bring the 2020 NEC , your government photo ID , a calculator you have used before , two pencils, and a highlighter if permitted. Arrive early. Read every question twice. Answer the easy ones first. Write the steps down. Check whether the question asked for a conductor or a device . And when an option offers something that sounds like a special Alaska rule, remember that Alaska adopted the NEC without amending it.