Study guide

4.2 Service-Entrance Conductors & Service Disconnecting Means

Alabama Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing, Exam Strategy & General Electrical Theory

1.1 Alabama Electrical Licensing, AECB Regulations & Prov Exam Structure 1.2 Electrical Fundamentals, Ohm's Law, Joule's Law & Power Formulas 1.3 Circuit Analysis: Series, Parallel & Combination Circuits

2 Chapter 2: NEC General Requirements, Working Spaces & Trade Knowledge

2.1 NEC Structure, Article 90 & Mandatory Article 100 Definitions 2.2 Electrical Equipment Spaces, Working Clearances & Dedicated Spaces 2.3 Electrical Connections, Terminations & Temperature Ratings 2.4 Electrical Plans, Symbols, Test Instruments & Troubleshooting

3 Chapter 3: Branch Circuits & Receptacle Outlets

3.1 Branch Circuit Ratings, Multiwire Branch Circuits & Required Outlets 3.2 Receptacle Spacing & Placement Requirements 3.3 GFCI Protection Requirements 3.4 AFCI Protection Requirements & Tamper-Resistant Receptacles

4 Chapter 4: Feeders, Services & System Disconnects

4.1 Feeder Sizing, Demand Factors & Neutral Calculations 4.2 Service-Entrance Conductors & Service Disconnecting Means 4.3 Service Equipment Rating, Emergency Disconnects & Surge Protection

5 Chapter 5: Load Calculations

5.1 Standard Dwelling Unit Load Calculations 5.2 Optional Dwelling Unit Load Calculations 5.3 Commercial Load Calculations & Non-Dwelling Demands

6 Chapter 6: Conductors, Cables & Flexible Cords

6.1 Conductor Types, Insulation & Temperature Ratings 6.2 Conductor Ampacity Derating & Correction Factors 6.3 Nonmetallic-Sheathed Cable (Type NM) & Underground Feeder (Type UF) 6.4 Armored Cable (Type AC) & Metal-Clad Cable (Type MC) 6.5 Service-Entrance Cable (Types SE & USE), Other Cables & Flexible Cords

7 Chapter 7: Raceways, Conduit Fill & Enclosures

7.1 Conduit Systems: EMT, RMC, IMC, and PVC 7.2 Flexible Raceways: FMC, LFMC, and LFNC 7.3 Conduit Fill Calculations & Chapter 9 Tables 7.4 Outlet, Device & Junction Box Sizing 7.5 Wireways, Auxiliary Gutters, Surface Raceways & Cable Trays 7.6 Underground Raceways, ENT & Protection from Physical Damage

8 Chapter 8: Grounding & Bonding Systems

8.1 Grounding Electrode System & Grounding Electrodes 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation 8.3 Main & System Bonding Jumpers 8.4 Equipment Grounding Conductors (EGC) Sizing & Identification

9 Chapter 9: Overcurrent Protection & Ground-Fault Protection

9.1 Standard Fuse & Circuit Breaker Ratings & Sizing 9.2 Small Conductor Rules & Overcurrent Exceptions 9.3 Tap Rules & Ground-Fault Protection of Equipment

10 Chapter 10: Motors, Motor Circuits & Transformers

10.1 Motor Conductor Sizing & Full-Load Current Tables 10.2 Motor Overload Protection 10.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 10.4 Transformer Sizing, Installation & Overcurrent Protection

11 Chapter 11: Special Occupancies, Hazardous Locations & Special Equipment

11.1 Hazardous (Classified) Locations: Class I, II, III 11.2 Healthcare Facilities & Patient Care Spaces 11.3 Swimming Pools, Spas & Hot Tubs 11.4 Agricultural Buildings, Mobile Homes, Marinas & RV Parks 11.5 Appliances, Electric Space Heating, Water Heaters & Special Equipment

12 Chapter 12: Lighting, Signs, Low Voltage, Communications & Safety

12.1 Luminaires, Lighting Outlets & Electric Signs 12.2 Fire Alarm Systems, Class 1, 2, 3 Circuits & Power-Limited Cables 12.3 Solar Photovoltaic (PV) & Energy Storage Systems 12.4 Electrical Safety, OSHA Regulations & NFPA 70E Fundamentals 12.5 Communications, CATV & Optical Fiber Systems (NEC Chapter 8) 12.6 OSHA Electrical Standards, Lockout/Tagout & Jobsite Safety

4.2 Service-Entrance Conductors & Service Disconnecting Means

Key Takeaways Explain This Topic AI

NEC Article 100 categorizes service conductors into overhead service conductors (drop to service head), underground service conductors (lateral to meter/disconnect), and service-entrance conductors (connecting service point to service equipment).

Under NEC 230.24(B), overhead service conductor vertical clearances above ground must be at least 10 feet for pedestrian walkways, 12 feet for residential driveways, and 18 feet over public streets, alleys, and commercial parking areas subject to truck traffic.

NEC 230.70(A)(1) mandates that the service disconnecting means must be installed in a readily accessible location either outside of a building/structure or inside nearest the point of entrance of the service conductors.

The 2023 NEC revision to Section 230.71 eliminates the traditional 'rule of six' in a single enclosure, requiring each of the two to six service disconnecting means to be located in separate enclosures, separate compartments of switchboards, or listed meter centers.

Under NEC 230.79(C), the minimum service disconnecting means rating for any one-family dwelling unit is strictly 100 amperes, 3-wire.

Last updated: September 2026

Service-Entrance Conductors & Service Disconnecting Means

Service-entrance conductors and service equipment deliver utility power to premises wiring. Governed by NEC Article 230 , service installations require compliance with clearance, burial, enclosure, and disconnect standards. Because service conductors lack downstream overcurrent protection ahead of the service disconnect, any line fault carries catastrophic arc-flash and fire hazards. For the Alabama Journeyman Electrician examination, mastering Article 230 rules—including the 2023 NEC overhaul of multiple disconnects—is essential for field safety and exam scoring.

1. Service Classifications & Boundaries (NEC Article 100 & 230.2)

Article 100 defines three service conductor classifications: overhead service conductors (utility service point to service head), underground service conductors (service point to meter or disconnect enclosure), and service-entrance conductors (connecting to service disconnect equipment). Under NEC 230.2 , a building must be supplied by only one service , except for fire pumps, emergency systems, capacity over 2,000A, or differing voltages/frequencies.

2. Overhead Service Clearances Above Grade (NEC 230.24(B))

Per NEC 230.24(B) , overhead service conductors (600V or less) must maintain minimum vertical clearances above grade:

10 Feet (3.05 m) : Over areas, sidewalks, or paths accessible to pedestrians only , and at the electric service entrance or lowest point of the drip loop, where voltage does not exceed 150 volts to ground.

12 Feet (3.66 m) : Over residential property and driveways , and commercial areas not subject to truck traffic, where voltage does not exceed 300 volts to ground.

15 Feet (4.57 m) : Over residential property and driveways where voltage exceeds 300 volts to ground.

18 Feet (5.49 m) : Over public streets, alleys, roads, and parking areas subject to truck traffic .

24.5 Feet (7.5 m) : Over track rails of railroads.

Clearances from Building Openings (NEC 230.9)

Under NEC 230.9(A) , overhead service conductors must maintain at least 3 feet (900 mm) of clearance from windows that open, doors, porches, balconies, stairs, and fire escapes. Exception: Conductors installed above the top level of a window are permitted closer than 3 feet.

3. Roof Clearances & Service Masts (NEC 230.24(A))

Under NEC 230.24(A) , overhead conductors above roofs must maintain an 8-foot (2.44 m) vertical clearance for 3 feet in all directions from the roof edge, subject to key exceptions:

Steep Pitch Roof (NEC 230.24(A) Ex. 2) : Where voltage between conductors does not exceed 300V and roof slope is at least 4 inches in 12 inches (4:12 pitch) , clearance may be reduced to 3 feet (900 mm) .

Through-Roof Mast (NEC 230.24(A) Ex. 3) : Where conductors pass over not more than 4 feet (1.22 m) of overhang to terminate at a mast within 6 feet (1.83 m) of the edge, clearance is permitted at 18 inches (450 mm) if voltage is not over 300V.

Per NEC 230.28 , service masts supporting overhead conductors must have adequate mechanical strength or guy bracing to withstand utility drop tension. Only service-drop conductors may attach to a mast.

4. Underground Lateral Protection & Sealing (NEC 230.30 & Table 300.5)

Underground service conductors must be installed in approved raceways or cables with minimum burial depths per NEC Table 300.5 : direct-buried cable ( 24 inches ), RMC/IMC ( 6 inches ), Schedule 40/80 PVC ( 18 inches ), or raceways under a 2-inch concrete slab ( 12 inches ). Per NEC 230.8 and 300.5(G) , underground service raceways entering buildings must be sealed with listed duct seal to block moisture and gas infiltration.

5. Service Disconnecting Means Location (NEC 230.70)

Under NEC 230.70(A)(1) , the service disconnecting means must be in a readily accessible location either outside the building or inside nearest the point of entrance of the service conductors.

Unfused service conductors inside buildings present severe fire hazards. Per NEC 230.6 , conductors are considered outside a building only when encased in at least 2 inches of concrete or brick , installed under 2 inches of concrete, or within a transformer vault. Service disconnects must never be installed in bathrooms (NEC 230.70(C)).

6. The 2023 NEC Overhaul of Section 230.71 ("Rule of Six")

Historically, up to six disconnects were permitted in a single panelboard without a main breaker. In the 2023 edition, NEC 230.71 was overhauled .

A service disconnecting means may still comprise up to six disconnects, but each must now be housed in:

  • A separate enclosure with a single disconnect,
  • A separate compartment of a listed multi-compartment switchboard or switchgear,
  • A listed metering center with individual disconnect compartments, or

Listed enclosed service disconnects.

Housing up to six service disconnects in a single panelboard is strictly prohibited to eliminate electrician arc-flash exposure to live, unfused service busbars.

7. Service Disconnect Rating Standards (NEC 230.79)

Under NEC 230.79 , service disconnect ratings must meet statutory minimums: 15A for single circuits, 30A for two 2-wire circuits, 100A 3-wire for one-family dwellings, and 60A for all other occupancies.

  • Service Parameter Governing Section NEC Requirement
  • Pedestrian Clearance NEC 230.24(B)(1) 10 ft min. above sidewalks and pedestrian areas
  • Residential Driveway NEC 230.24(B)(2) 12 ft min. for systems ≤ 300 V \le 300\text{V} ≤ 300 V to ground
  • Public Street / Alley NEC 230.24(B)(4) 18 ft min. over truck traffic roads and commercial parking

Through-Roof Mast NEC 230.24(A) Ex. 3 18 in. clearance if within 6 ft of edge and ≤ 4 ft \le 4\text{ ft} ≤ 4 ft of overhang

  • Building Openings NEC 230.9(A) 3 ft min. clearance from openable windows, doors, stairs
  • Single-Family Disconnect NEC 230.79(C) 100A, 3-wire absolute minimum rating
  • Multiple Disconnects NEC 230.71 Max. 6 disconnects in separate enclosures or compartments