Study guide
8.2 Grounding Electrode Conductor (GEC) Sizing & Installation
Alabama Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing, Exam Strategy & General Electrical Theory
1.1 Alabama Electrical Licensing, AECB Regulations & Prov Exam Structure 1.2 Electrical Fundamentals, Ohm's Law, Joule's Law & Power Formulas 1.3 Circuit Analysis: Series, Parallel & Combination Circuits
2 Chapter 2: NEC General Requirements, Working Spaces & Trade Knowledge
2.1 NEC Structure, Article 90 & Mandatory Article 100 Definitions 2.2 Electrical Equipment Spaces, Working Clearances & Dedicated Spaces 2.3 Electrical Connections, Terminations & Temperature Ratings 2.4 Electrical Plans, Symbols, Test Instruments & Troubleshooting
3 Chapter 3: Branch Circuits & Receptacle Outlets
3.1 Branch Circuit Ratings, Multiwire Branch Circuits & Required Outlets 3.2 Receptacle Spacing & Placement Requirements 3.3 GFCI Protection Requirements 3.4 AFCI Protection Requirements & Tamper-Resistant Receptacles
4 Chapter 4: Feeders, Services & System Disconnects
4.1 Feeder Sizing, Demand Factors & Neutral Calculations 4.2 Service-Entrance Conductors & Service Disconnecting Means 4.3 Service Equipment Rating, Emergency Disconnects & Surge Protection
5 Chapter 5: Load Calculations
5.1 Standard Dwelling Unit Load Calculations 5.2 Optional Dwelling Unit Load Calculations 5.3 Commercial Load Calculations & Non-Dwelling Demands
6 Chapter 6: Conductors, Cables & Flexible Cords
6.1 Conductor Types, Insulation & Temperature Ratings 6.2 Conductor Ampacity Derating & Correction Factors 6.3 Nonmetallic-Sheathed Cable (Type NM) & Underground Feeder (Type UF) 6.4 Armored Cable (Type AC) & Metal-Clad Cable (Type MC) 6.5 Service-Entrance Cable (Types SE & USE), Other Cables & Flexible Cords
7 Chapter 7: Raceways, Conduit Fill & Enclosures
7.1 Conduit Systems: EMT, RMC, IMC, and PVC 7.2 Flexible Raceways: FMC, LFMC, and LFNC 7.3 Conduit Fill Calculations & Chapter 9 Tables 7.4 Outlet, Device & Junction Box Sizing 7.5 Wireways, Auxiliary Gutters, Surface Raceways & Cable Trays 7.6 Underground Raceways, ENT & Protection from Physical Damage
8 Chapter 8: Grounding & Bonding Systems
8.1 Grounding Electrode System & Grounding Electrodes 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation 8.3 Main & System Bonding Jumpers 8.4 Equipment Grounding Conductors (EGC) Sizing & Identification
9 Chapter 9: Overcurrent Protection & Ground-Fault Protection
9.1 Standard Fuse & Circuit Breaker Ratings & Sizing 9.2 Small Conductor Rules & Overcurrent Exceptions 9.3 Tap Rules & Ground-Fault Protection of Equipment
10 Chapter 10: Motors, Motor Circuits & Transformers
10.1 Motor Conductor Sizing & Full-Load Current Tables 10.2 Motor Overload Protection 10.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 10.4 Transformer Sizing, Installation & Overcurrent Protection
11 Chapter 11: Special Occupancies, Hazardous Locations & Special Equipment
11.1 Hazardous (Classified) Locations: Class I, II, III 11.2 Healthcare Facilities & Patient Care Spaces 11.3 Swimming Pools, Spas & Hot Tubs 11.4 Agricultural Buildings, Mobile Homes, Marinas & RV Parks 11.5 Appliances, Electric Space Heating, Water Heaters & Special Equipment
12 Chapter 12: Lighting, Signs, Low Voltage, Communications & Safety
12.1 Luminaires, Lighting Outlets & Electric Signs 12.2 Fire Alarm Systems, Class 1, 2, 3 Circuits & Power-Limited Cables 12.3 Solar Photovoltaic (PV) & Energy Storage Systems 12.4 Electrical Safety, OSHA Regulations & NFPA 70E Fundamentals 12.5 Communications, CATV & Optical Fiber Systems (NEC Chapter 8) 12.6 OSHA Electrical Standards, Lockout/Tagout & Jobsite Safety
8.2 Grounding Electrode Conductor (GEC) Sizing & Installation
Key Takeaways Explain This Topic AI
The Grounding Electrode Conductor (GEC) is sized under NEC Table 250.66 based on the cross-sectional area of the largest ungrounded service-entrance conductor or the sum of parallel service conductors.
NEC 250.66(A), (B), and (C) establish critical upper limits: a GEC connecting solely to rod/pipe/plate electrodes is never required to exceed 6 AWG copper; solely to a concrete-encased electrode never exceeds 4 AWG copper; and solely to a ground ring never exceeds the ring conductor size.
NEC 250.64(C) requires the GEC to be installed in one continuous length without splices, except where joined by irreversible compression-type connectors listed as grounding equipment or by exothermic welding.
Under NEC 250.64(E), any ferrous metal raceway or enclosure enclosing a GEC must be bonded at both ends to the enclosure and electrode to prevent inductive choking of high-frequency lightning currents.
Aluminum or copper-clad aluminum GECs are strictly prohibited from being installed in direct contact with masonry or the earth, or subjected to corrosive conditions, per NEC 250.64(A).
Last updated: September 2026
- 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation
- 1. Definition and Function of the GEC (NEC Article 100 & 250.24(D))
NEC Article 100 defines the Grounding Electrode Conductor (GEC) as the conductor used to connect the system grounded conductor or the equipment to a grounding electrode or to a point on the grounding electrode system.
The GEC connects the service enclosure and neutral conductor directly to earth. Unlike circuit conductors sized for loads or equipment grounding conductors sized for fault currents, the GEC is sized primarily to dissipate lightning discharges, high-voltage surges, and line crossovers into earth while establishing a zero-volt ground reference.
2. Table 250.66 Sizing Methodology
Grounding Electrode Conductors are sized under NEC Table 250.66 based on the cross-sectional area of the largest ungrounded service conductor or equivalent area for parallel conductors.
NEC Table 250.66: Grounding Electrode Conductor Sizing
Largest Ungrounded Service Conductor (Copper) Largest Ungrounded Service Conductor (Aluminum / Copper-Clad) Minimum Size Copper GEC Minimum Size Aluminum GEC
- 2 AWG or smaller 1/0 AWG or smaller 8 AWG 6 AWG
- 1 AWG or 1/0 AWG 2/0 AWG or 3/0 AWG 6 AWG 4 AWG
- 2/0 AWG or 3/0 AWG 4/0 AWG or 250 kcmil 4 AWG 2 AWG
- Over 3/0 AWG through 350 kcmil Over 250 kcmil through 500 kcmil 2 AWG 1/0 AWG
- Over 350 kcmil through 600 kcmil Over 500 kcmil through 900 kcmil 1/0 AWG 3/0 AWG
- Over 600 kcmil through 1100 kcmil Over 900 kcmil through 1750 kcmil 2/0 AWG 4/0 AWG
- Over 1100 kcmil Over 1750 kcmil 3/0 AWG 250 kcmil
- Sizing for Parallel Service Conductors
When service conductors are installed in parallel sets, the equivalent size is determined by summing the circular mil area of the parallel conductors for any one phase : Equivalent Area = N × Circular Mils of One Parallel Conductor \text{Equivalent Area} = N \times \text{Circular Mils of One Parallel Conductor} Equivalent Area = N × Circular Mils of One Parallel Conductor
Example : A 1200A service has three parallel 500 kcmil copper conductors per phase ( 3 × 500 kcmil = 1,500 kcmil 3 \times 500\text{ kcmil} = 1{,}500\text{ kcmil} 3 × 500 kcmil = 1 , 500 kcmil ). Because 1,500 kcmil 1{,}500\text{ kcmil} 1 , 500 kcmil exceeds 1100 kcmil, Table 250.66 requires a 3/0 AWG copper GEC (or 250 kcmil aluminum).
3. Maximum Size Caps for Specific Electrodes (NEC 250.66(A), (B), (C))
While Table 250.66 governs main GECs to water pipe or building steel, the code establishes hard upper limits for conductors connecting solely to specific electrodes:
Rod, Pipe, or Plate Electrodes (NEC 250.66(A)) : Where the GEC connects solely to a rod, pipe, or plate electrode, that portion of the conductor is never required to be larger than 6 AWG copper wire or 4 AWG aluminum wire .
Concrete-Encased Electrodes (NEC 250.66(B)) : Where the GEC connects solely to a concrete-encased electrode (Ufer ground), that portion of the conductor is never required to be larger than 4 AWG copper wire .
Ground Rings (NEC 250.66(C)) : Where the GEC connects solely to a ground ring, it is never required to be larger than the conductor used for the ground ring itself (minimum 2 AWG copper per NEC 250.52(A)(4)).
4. Installation Rules and Mechanical Protection (NEC 250.64)
NEC 250.64 governs physical installation and protection of Grounding Electrode Conductors:
Material Restrictions (NEC 250.64(A)) : Bare aluminum or copper-clad aluminum GECs are strictly prohibited from being installed in direct contact with masonry, concrete, or earth, or outdoors within 18 inches (450 mm) of finished grade.
Physical Protection (NEC 250.64(B)) : GECs 6 AWG and larger exposed to physical damage must be enclosed in RMC, IMC, PVC, RTRC, EMT, or cable armor. A 6 AWG or larger copper GEC free from physical damage may be run exposed along building surfaces. GECs smaller than 6 AWG (such as 8 AWG) must always be enclosed in conduit or cable armor .
Continuous Run Mandate (NEC 250.64(C)) : GECs must be installed in one continuous length without splices or joints, except:
Irreversible compression-type connectors listed as grounding equipment.
Exothermic welding.
Connections to busbars (minimum 1/4 in × \times × 2 in) located in accessible locations.
5. Inductive Magnetic Choke & Ferrous Metal Enclosure Bonding (NEC 250.64(E))
Lightning strikes generate high-frequency surge currents exceeding hundreds of kilohertz:
Physics of Magnetic Choke : When high-frequency current passes through a conductor enclosed inside a ferrous (steel) raceway, the raceway acts as an iron inductor core. This induces severe inductive reactance ( X L = 2 π f L X_L = 2\pi f L X L = 2 π f L ), choking off surge current flow.
The Code Solution (NEC 250.64(E)) : Any ferrous metal raceway enclosing a GEC must be bonded at each end to the electrical enclosure and the grounding electrode. Bonding both ends places the steel conduit in electrical parallel with the GEC. The induced currents cancel the net magnetic flux, eliminating inductive choke and allowing high-frequency surges to dissipate safely into earth.
6. Grounding Connection Clamps (NEC 250.70) & Worked Sizing Examples
Grounding clamps must be listed for the electrode material. Clamps installed underground or encased in concrete must be listed for direct burial and stamped "DB".
Worked Sizing Example
A 480V service has two parallel 350 kcmil copper conductors per phase ( 350 + 350 = 700 kcmil 350 + 350 = 700\text{ kcmil} 350 + 350 = 700 kcmil ). Electrodes include a metal water pipe and two driven ground rods.
GEC to Water Pipe : Sized per Table 250.66 for 700 kcmil copper. Requires 2/0 AWG copper .
GEC to Ground Rods : Sized per NEC 250.66(A). The tap running solely to the ground rods is capped at 6 AWG copper .