Study guide
8.3 Main & System Bonding Jumpers
Alabama Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing, Exam Strategy & General Electrical Theory
1.1 Alabama Electrical Licensing, AECB Regulations & Prov Exam Structure 1.2 Electrical Fundamentals, Ohm's Law, Joule's Law & Power Formulas 1.3 Circuit Analysis: Series, Parallel & Combination Circuits
2 Chapter 2: NEC General Requirements, Working Spaces & Trade Knowledge
2.1 NEC Structure, Article 90 & Mandatory Article 100 Definitions 2.2 Electrical Equipment Spaces, Working Clearances & Dedicated Spaces 2.3 Electrical Connections, Terminations & Temperature Ratings 2.4 Electrical Plans, Symbols, Test Instruments & Troubleshooting
3 Chapter 3: Branch Circuits & Receptacle Outlets
3.1 Branch Circuit Ratings, Multiwire Branch Circuits & Required Outlets 3.2 Receptacle Spacing & Placement Requirements 3.3 GFCI Protection Requirements 3.4 AFCI Protection Requirements & Tamper-Resistant Receptacles
4 Chapter 4: Feeders, Services & System Disconnects
4.1 Feeder Sizing, Demand Factors & Neutral Calculations 4.2 Service-Entrance Conductors & Service Disconnecting Means 4.3 Service Equipment Rating, Emergency Disconnects & Surge Protection
5 Chapter 5: Load Calculations
5.1 Standard Dwelling Unit Load Calculations 5.2 Optional Dwelling Unit Load Calculations 5.3 Commercial Load Calculations & Non-Dwelling Demands
6 Chapter 6: Conductors, Cables & Flexible Cords
6.1 Conductor Types, Insulation & Temperature Ratings 6.2 Conductor Ampacity Derating & Correction Factors 6.3 Nonmetallic-Sheathed Cable (Type NM) & Underground Feeder (Type UF) 6.4 Armored Cable (Type AC) & Metal-Clad Cable (Type MC) 6.5 Service-Entrance Cable (Types SE & USE), Other Cables & Flexible Cords
7 Chapter 7: Raceways, Conduit Fill & Enclosures
7.1 Conduit Systems: EMT, RMC, IMC, and PVC 7.2 Flexible Raceways: FMC, LFMC, and LFNC 7.3 Conduit Fill Calculations & Chapter 9 Tables 7.4 Outlet, Device & Junction Box Sizing 7.5 Wireways, Auxiliary Gutters, Surface Raceways & Cable Trays 7.6 Underground Raceways, ENT & Protection from Physical Damage
8 Chapter 8: Grounding & Bonding Systems
8.1 Grounding Electrode System & Grounding Electrodes 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation 8.3 Main & System Bonding Jumpers 8.4 Equipment Grounding Conductors (EGC) Sizing & Identification
9 Chapter 9: Overcurrent Protection & Ground-Fault Protection
9.1 Standard Fuse & Circuit Breaker Ratings & Sizing 9.2 Small Conductor Rules & Overcurrent Exceptions 9.3 Tap Rules & Ground-Fault Protection of Equipment
10 Chapter 10: Motors, Motor Circuits & Transformers
10.1 Motor Conductor Sizing & Full-Load Current Tables 10.2 Motor Overload Protection 10.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 10.4 Transformer Sizing, Installation & Overcurrent Protection
11 Chapter 11: Special Occupancies, Hazardous Locations & Special Equipment
11.1 Hazardous (Classified) Locations: Class I, II, III 11.2 Healthcare Facilities & Patient Care Spaces 11.3 Swimming Pools, Spas & Hot Tubs 11.4 Agricultural Buildings, Mobile Homes, Marinas & RV Parks 11.5 Appliances, Electric Space Heating, Water Heaters & Special Equipment
12 Chapter 12: Lighting, Signs, Low Voltage, Communications & Safety
12.1 Luminaires, Lighting Outlets & Electric Signs 12.2 Fire Alarm Systems, Class 1, 2, 3 Circuits & Power-Limited Cables 12.3 Solar Photovoltaic (PV) & Energy Storage Systems 12.4 Electrical Safety, OSHA Regulations & NFPA 70E Fundamentals 12.5 Communications, CATV & Optical Fiber Systems (NEC Chapter 8) 12.6 OSHA Electrical Standards, Lockout/Tagout & Jobsite Safety
8.3 Main & System Bonding Jumpers
Key Takeaways Explain This Topic AI
Bonding connects metal non-current-carrying parts together to create an effective low-impedance ground-fault current path back to the electrical source to trigger the overcurrent protective device.
NEC 250.4(A)(5) explicitly states that the earth shall not be considered as an effective ground-fault current path, because soil resistance is too high to produce the current needed to trip an overcurrent device.
The Main Bonding Jumper (MBJ), governed by NEC 250.28, connects the grounded system conductor (neutral) to the equipment grounding conductor and service disconnect enclosure at the service equipment.
The MBJ is sized using NEC Table 250.102(C)(1) based on the largest ungrounded service conductor, and for services exceeding 1100 kcmil copper or 1750 kcmil aluminum, the jumper must have an area not less than 12.5% of the phase conductor circular mils.
Under NEC 250.24(A)(5) and 250.142(B), neutral-to-ground connections are strictly prohibited on the load side of the service disconnecting means to prevent dangerous circulating neutral current on equipment enclosures and raceways.
Last updated: September 2026
- 8.3 Main & System Bonding Jumpers
- 1. Grounding vs. Bonding: The Life-Safety Distinction
While grounding connects systems to earth for lightning and surge protection, bonding is the active life-safety mechanism that prevents fatal electrocution and fires during ground faults.
Under NEC 250.4(A)(3) and (A)(4) , non-current-carrying metallic parts—switchboards, panels, raceways, boxes, and equipment frames—must be bonded together. The goal is to form an effective ground-fault current path: an electrically continuous, permanent, low-impedance circuit that facilitates the instantaneous operation of overcurrent protective devices (OCPDs). Without it, ground faults leave enclosures energized at line voltage.
2. Why the Earth Cannot Clear a Ground Fault (NEC 250.4(A)(5))
NEC 250.4(A)(5) explicitly commands: "The earth shall not be considered as an effective ground-fault current path."
To understand why, analyze an electrical fault using Ohm's Law ( I = E / R I = E / R I = E / R ):
Mathematical Demonstration
Assume an ungrounded 120-volt conductor contacts the metal frame of an appliance. Suppose the equipment grounding conductor is broken, and the only path back to the source is through a code-compliant 25-ohm ground rod: I fault = 120 Volts 25 Ω = 4.8 Amperes I_{\text{fault}} = \frac{120\text{ Volts}}{25\ \Omega} = 4.8\text{ Amperes} I fault = 25 Ω 120 Volts = 4.8 Amperes
The Fatal Result
A 20-ampere circuit breaker requires 20A to trip thermally, and 100 to 200A to trip magnetically. At 4.8 amperes , the breaker will never trip .
The metal appliance frame remains energized at 120 volts indefinitely. Anyone touching the frame while standing on earth completes the circuit.
The Low-Impedance Bonded Path
When an equipment grounding conductor and main bonding jumper return the fault directly to the utility neutral, path impedance is negligible (approximately 0.1 Ω 0.1\ \Omega 0.1 Ω ): I fault = 120 Volts 0.1 Ω = 1,200 Amperes I_{\text{fault}} = \frac{120\text{ Volts}}{0.1\ \Omega} = 1{,}200\text{ Amperes} I fault = 0.1 Ω 120 Volts = 1 , 200 Amperes
This 1,200-ampere surge trips the 20A breaker in under 16 milliseconds, instantly eliminating shock and fire hazards.
3. The Main Bonding Jumper (MBJ) at Service Equipment (NEC 250.28)
Governed by NEC 250.28 , the Main Bonding Jumper (MBJ) is the vital connection installed at the service disconnecting means (NEC 250.24(B)) that connects:
The grounded service conductor (system neutral).
The equipment grounding conductor (EGC) busbar.
The service disconnect enclosure.
The MBJ provides the sole return path from building equipment grounding back to the utility transformer neutral.
Permissible Construction and Finish (NEC 250.28(A) & (B))
Materials : Wire jumper, busbar, screw, or similar suitable conductor.
Green Screw Finish (NEC 250.28(B)) : If a screw is used as the MBJ, it must have a green finish that remains visible after installation . This unmistakable identification enables electrical inspectors to verify that the service neutral is properly bonded to the enclosure.
4. Sizing the Main Bonding Jumper (NEC 250.28(D) & Table 250.102(C)(1))
The MBJ is sized using NEC Table 250.102(C)(1) based on the largest ungrounded service conductor or equivalent area for parallel conductors.
NEC Table 250.102(C)(1): Main Bonding Jumper Sizing
Largest Ungrounded Service Conductor (Copper) Largest Ungrounded Service Conductor (Aluminum / Copper-Clad) Minimum Size Copper Bonding Jumper Minimum Size Aluminum Bonding Jumper
- 2 AWG or smaller 1/0 AWG or smaller 8 AWG 6 AWG
- 1 AWG or 1/0 AWG 2/0 AWG or 3/0 AWG 6 AWG 4 AWG
- 2/0 AWG or 3/0 AWG 4/0 AWG or 250 kcmil 4 AWG 2 AWG
- Over 3/0 AWG through 350 kcmil Over 250 kcmil through 500 kcmil 2 AWG 1/0 AWG
- Over 350 kcmil through 600 kcmil Over 500 kcmil through 900 kcmil 1/0 AWG 3/0 AWG
- Over 600 kcmil through 1100 kcmil Over 900 kcmil through 1750 kcmil 2/0 AWG 4/0 AWG
- Over 1100 kcmil Over 1750 kcmil 12.5% of Phase Area 12.5% of Phase Area
- The 12.5% Rule for Large Services (NEC 250.102(C)(1) Note 1 & 250.28(D)(1))
Where ungrounded phase conductors exceed 1,100 kcmil copper or 1,750 kcmil aluminum , the bonding jumper must have an area not less than 12.5% (one-eighth) of the total circular mil area of the largest phase conductor set.
Worked Calculation : A service has four parallel 500 kcmil copper conductors per phase ( 4 × 500,000 = 2,000,000 cmils = 2,000 kcmil 4 \times 500{,}000 = 2{,}000{,}000\text{ cmils} = 2{,}000\text{ kcmil} 4 × 500 , 000 = 2 , 000 , 000 cmils = 2 , 000 kcmil ). Required Area = 2,000,000 cmils × 0.125 = 250,000 cmils = 250 kcmil copper \text{Required Area} = 2{,}000{,}000\text{ cmils} \times 0.125 = 250{,}000\text{ cmils} = 250\text{ kcmil copper} Required Area = 2 , 000 , 000 cmils × 0.125 = 250 , 000 cmils = 250 kcmil copper
5. System Bonding Jumpers (SBJ) for Separately Derived Systems (NEC 250.30)
Separately derived systems have no direct connection to the utility neutral. Under NEC 250.30(A)(1) , an unspliced System Bonding Jumper (SBJ) must connect the derived neutral terminal ( X 0 X_0 X 0 ) to the transformer enclosure and equipment grounding conductors.
Location : Installed at any single point from the source to the first disconnecting means (in the transformer or the first panel, but never at both ).
Sizing : Sized per Table 250.102(C)(1) based on derived secondary phase conductors.
6. Downstream Neutral Isolation & Objectionable Current (NEC 250.24(A)(5) & 250.142(B))
Under NEC 250.24(A)(5) and 250.142(B) , the neutral conductor must never be connected to ground or enclosures on the load side of the service disconnect . In every subpanel, the neutral busbar must remain 100% electrically floating and isolated from the enclosure.
Dangers of Objectionable Current
Bonding the neutral in a subpanel places the neutral and metallic grounding paths in parallel. Normal neutral return current divides between the neutral wire and metallic building structures:
Shock Hazards : Metallic panel enclosures and conduits continuously carry live neutral current.
Fire Hazards : Loose conduit couplings arc and overheat from circulating current.
Equipment Malfunctions : Ground loops create electromagnetic interference and cause nuisance tripping of GFCI and AFCI devices.