Study guide

12.3 Solar Photovoltaic (PV) & Energy Storage Systems

Alabama Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing, Exam Strategy & General Electrical Theory

1.1 Alabama Electrical Licensing, AECB Regulations & Prov Exam Structure 1.2 Electrical Fundamentals, Ohm's Law, Joule's Law & Power Formulas 1.3 Circuit Analysis: Series, Parallel & Combination Circuits

2 Chapter 2: NEC General Requirements, Working Spaces & Trade Knowledge

2.1 NEC Structure, Article 90 & Mandatory Article 100 Definitions 2.2 Electrical Equipment Spaces, Working Clearances & Dedicated Spaces 2.3 Electrical Connections, Terminations & Temperature Ratings 2.4 Electrical Plans, Symbols, Test Instruments & Troubleshooting

3 Chapter 3: Branch Circuits & Receptacle Outlets

3.1 Branch Circuit Ratings, Multiwire Branch Circuits & Required Outlets 3.2 Receptacle Spacing & Placement Requirements 3.3 GFCI Protection Requirements 3.4 AFCI Protection Requirements & Tamper-Resistant Receptacles

4 Chapter 4: Feeders, Services & System Disconnects

4.1 Feeder Sizing, Demand Factors & Neutral Calculations 4.2 Service-Entrance Conductors & Service Disconnecting Means 4.3 Service Equipment Rating, Emergency Disconnects & Surge Protection

5 Chapter 5: Load Calculations

5.1 Standard Dwelling Unit Load Calculations 5.2 Optional Dwelling Unit Load Calculations 5.3 Commercial Load Calculations & Non-Dwelling Demands

6 Chapter 6: Conductors, Cables & Flexible Cords

6.1 Conductor Types, Insulation & Temperature Ratings 6.2 Conductor Ampacity Derating & Correction Factors 6.3 Nonmetallic-Sheathed Cable (Type NM) & Underground Feeder (Type UF) 6.4 Armored Cable (Type AC) & Metal-Clad Cable (Type MC) 6.5 Service-Entrance Cable (Types SE & USE), Other Cables & Flexible Cords

7 Chapter 7: Raceways, Conduit Fill & Enclosures

7.1 Conduit Systems: EMT, RMC, IMC, and PVC 7.2 Flexible Raceways: FMC, LFMC, and LFNC 7.3 Conduit Fill Calculations & Chapter 9 Tables 7.4 Outlet, Device & Junction Box Sizing 7.5 Wireways, Auxiliary Gutters, Surface Raceways & Cable Trays 7.6 Underground Raceways, ENT & Protection from Physical Damage

8 Chapter 8: Grounding & Bonding Systems

8.1 Grounding Electrode System & Grounding Electrodes 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation 8.3 Main & System Bonding Jumpers 8.4 Equipment Grounding Conductors (EGC) Sizing & Identification

9 Chapter 9: Overcurrent Protection & Ground-Fault Protection

9.1 Standard Fuse & Circuit Breaker Ratings & Sizing 9.2 Small Conductor Rules & Overcurrent Exceptions 9.3 Tap Rules & Ground-Fault Protection of Equipment

10 Chapter 10: Motors, Motor Circuits & Transformers

10.1 Motor Conductor Sizing & Full-Load Current Tables 10.2 Motor Overload Protection 10.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 10.4 Transformer Sizing, Installation & Overcurrent Protection

11 Chapter 11: Special Occupancies, Hazardous Locations & Special Equipment

11.1 Hazardous (Classified) Locations: Class I, II, III 11.2 Healthcare Facilities & Patient Care Spaces 11.3 Swimming Pools, Spas & Hot Tubs 11.4 Agricultural Buildings, Mobile Homes, Marinas & RV Parks 11.5 Appliances, Electric Space Heating, Water Heaters & Special Equipment

12 Chapter 12: Lighting, Signs, Low Voltage, Communications & Safety

12.1 Luminaires, Lighting Outlets & Electric Signs 12.2 Fire Alarm Systems, Class 1, 2, 3 Circuits & Power-Limited Cables 12.3 Solar Photovoltaic (PV) & Energy Storage Systems 12.4 Electrical Safety, OSHA Regulations & NFPA 70E Fundamentals 12.5 Communications, CATV & Optical Fiber Systems (NEC Chapter 8) 12.6 OSHA Electrical Standards, Lockout/Tagout & Jobsite Safety

12.3 Solar Photovoltaic (PV) & Energy Storage Systems

Key Takeaways Explain This Topic AI

NEC Article 690 governs Solar Photovoltaic (PV) systems, establishing rigorous standards for system architecture, DC string combiner boxes, inverters, and grounding.

Under NEC 690.7, maximum PV system DC voltage is determined by multiplying module rated open-circuit voltage (Voc) by cold-weather temperature correction coefficients, accounting for increased voltage at sub-freezing temperatures.

NEC 690.12 mandates building-mounted PV Rapid Shutdown within 30 seconds of initiation: controlling DC conductors outside the array boundary to 30 volts or less, and conductors inside the array boundary to 80 volts or less.

PV source and output circuit conductors and overcurrent devices must be sized at a minimum of 156% of module short-circuit current (Isc), factoring the 125% maximum circuit current multiplier and the 125% continuous duty multiplier (1.25 x 1.25 = 1.56).

NEC Article 706 regulates Energy Storage Systems (ESS), requiring an accessible system disconnect located within sight of the ESS and mandatory dedicated working clearances matching NEC 110.26.

Last updated: September 2026

  • 12.3 Solar Photovoltaic (PV) & Energy Storage Systems
  • Photovoltaic Architecture & System Topologies Under NEC Article 690

National Electrical Code Article 690 establishes electrical safety standards for Solar Photovoltaic (PV) systems, governing equipment from exposed rooftop DC arrays through grid-interactive inverters and utility interconnections. PV installations introduce unique electrical hazards because photovoltaic cells generate direct current (DC) electricity whenever exposed to solar radiation. Unlike conventional AC circuits, DC currents do not pass through a periodic zero-voltage crossing, making DC electrical arcs self-sustaining, intensely destructive, and capable of jumping wide air gaps.

A standard photovoltaic installation comprises distinct architectural stages:

Photovoltaic Cell : The elementary semiconductor diode converting photons to direct current, producing approximately 0.5 to 0.6 volts DC.

PV Module : An environmentally sealed frame containing series-connected photovoltaic cells.

PV String : Multiple PV modules wired in series to elevate circuit voltage to inverter operational thresholds.

PV Array : A complete mechanically integrated assembly of strings connected in parallel through a DC combiner box.

Inverter : Power electronics converting variable DC voltage into synchronized alternating current (AC) matching utility voltage and frequency.

Equipment Listing : Under NEC 690.4(B), all modules, combiners, inverters, and rapid shutdown devices must be listed and identified for PV system applications.

Maximum PV System DC Voltage Calculations (NEC 690.7)

Photovoltaic system conductors, switches, fuses, and modules must be rated to withstand the maximum direct current voltage generated by the array. In crystalline silicon photovoltaic cells, operating voltage is inversely related to ambient temperature: as operating temperatures drop, module open-circuit voltage ( V o c V_{oc} V oc ​ ) increases significantly . An installation generating 450 volts DC at 77°F (25°C) can easily exceed 550 volts DC during freezing sub-zero winter mornings.

Under NEC 690.7(A), the maximum PV system DC voltage is determined using one of two approved engineering methods:

Manufacturer Temperature Coefficient : Utilizing the module manufacturer's certified temperature coefficient of V o c V_{oc} V oc ​ applied to the lowest expected ambient temperature recorded for the installation site.

Table 690.7(A) Voltage Correction Factors : Multiplying the rated module open-circuit voltage by the ambient temperature correction factor from Table 690.7(A). For example, at temperatures from − 1 ∘ C -1^\circ\text{C} − 1 ∘ C to − 5 ∘ C -5^\circ\text{C} − 5 ∘ C ( 30 ∘ F 30^\circ\text{F} 3 0 ∘ F to 23 ∘ F 23^\circ\text{F} 2 3 ∘ F ), the factor is 1.12; from − 16 ∘ C -16^\circ\text{C} − 1 6 ∘ C to − 20 ∘ C -20^\circ\text{C} − 2 0 ∘ C ( 3 ∘ F 3^\circ\text{F} 3 ∘ F to − 4 ∘ F -4^\circ\text{F} − 4 ∘ F ), the multiplier rises to 1.18.

Voltage Limitations

Per NEC 690.7(B), the maximum PV system voltage on one- and two-family dwellings cannot exceed 600 volts DC . Commercial, industrial, and ground-mounted utility arrays are permitted to operate at potentials up to 1,000 volts DC or 1,500 volts DC when utilizing listed industrial equipment.

Rapid Shutdown of PV Systems on Buildings (NEC 690.12)

When utility power is shut off during a structural fire, rooftop solar arrays continue producing lethal DC voltage whenever daylight strikes the modules. To safeguard emergency responders from fatal electrocution while performing rooftop ventilation or overhaul operations, NEC 690.12 mandates building-mounted PV Rapid Shutdown systems.

Controlled Operational Thresholds

The rapid shutdown system must be initiated from a clearly identified, readily accessible switch (such as the main service disconnect or a dedicated rapid shutdown initiator). Within 30 seconds of initiation , circuit voltages must drop to or below the following strict thresholds:

Outside the Array Boundary : Conductors located more than 1 foot (305 mm) from the array perimeter, or extending more than 3 feet (900 mm) from the point of building penetration, must be controlled to 30 volts or less .

Inside the Array Boundary : Conductors located inside the array or within 1 foot of the array perimeter must be controlled to 80 volts or less .

Compliance inside the array boundary is almost universally achieved using Module-Level Power Electronics (MLPE), such as microinverters or DC power optimizers with integrated rapid shutdown compliance, which de-energize string conductors at the individual panel level.

Sizing PV Conductors & Overcurrent Protection (NEC 690.8)

Photovoltaic circuits are subject to high solar irradiance events where snow reflection, cloud-edge lensing, and cool ambient conditions cause array output to exceed rated factory specifications.

The 156% Conductor and Overcurrent Sizing Rule

Maximum Circuit Current (NEC 690.8(A)(1)) : The maximum continuous current for a PV source circuit is calculated as 125% of the module rated short-circuit current ( I s c I_{sc} I sc ​ ) : Maximum Circuit Current = I s c × 1.25 \text{Maximum Circuit Current} = I_{sc} \times 1.25 Maximum Circuit Current = I sc ​ × 1.25

Continuous Duty Sizing (NEC 690.8(B)) : Because solar circuits operate under peak sunshine for three hours or more, PV circuits are classified as continuous loads. Under NEC 690.8(B), conductors and overcurrent protective devices must be sized at 125% of the maximum circuit current: Conductor Ampacity / OCPD = Maximum Current × 1.25 = ( I s c × 1.25 ) × 1.25 = I s c × 1.5625 \text{Conductor Ampacity / OCPD} = \text{Maximum Current} \times 1.25 = (I_{sc} \times 1.25) \times 1.25 = I_{sc} \times 1.5625 Conductor Ampacity / OCPD = Maximum Current × 1.25 = ( I sc ​ × 1.25 ) × 1.25 = I sc ​ × 1.5625

Therefore, PV source circuit conductors and overcurrent devices must be rated at not less than 156% of module rated short-circuit current ( I s c I_{sc} I sc ​ ) before applying temperature or conduit fill derating factors!

Energy Storage Systems (ESS) Under NEC Article 706

Energy Storage Systems (ESS), including advanced lithium-ion and flow battery installations, are governed by NEC Article 706:

Disconnecting Means (NEC 706.15) : A readily accessible disconnecting means must be provided within sight of the ESS. If the disconnect is located remotely, it must be lockable in the open position per NEC 110.25, and a directory plaque must be posted at the ESS indicating the disconnect's precise location.

Dedicated Working Clearances (NEC 706.16) : Working clearances around ESS equipment must strictly satisfy NEC 110.26 standards: a minimum of 3 feet of front depth clearance , a width of at least 30 inches or equipment width, and 6.5 feet of headroom , ensuring safe maintenance and emergency access.