Study guide

10.2 Motor Overload Protection

Alabama Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing, Exam Strategy & General Electrical Theory

1.1 Alabama Electrical Licensing, AECB Regulations & Prov Exam Structure 1.2 Electrical Fundamentals, Ohm's Law, Joule's Law & Power Formulas 1.3 Circuit Analysis: Series, Parallel & Combination Circuits

2 Chapter 2: NEC General Requirements, Working Spaces & Trade Knowledge

2.1 NEC Structure, Article 90 & Mandatory Article 100 Definitions 2.2 Electrical Equipment Spaces, Working Clearances & Dedicated Spaces 2.3 Electrical Connections, Terminations & Temperature Ratings 2.4 Electrical Plans, Symbols, Test Instruments & Troubleshooting

3 Chapter 3: Branch Circuits & Receptacle Outlets

3.1 Branch Circuit Ratings, Multiwire Branch Circuits & Required Outlets 3.2 Receptacle Spacing & Placement Requirements 3.3 GFCI Protection Requirements 3.4 AFCI Protection Requirements & Tamper-Resistant Receptacles

4 Chapter 4: Feeders, Services & System Disconnects

4.1 Feeder Sizing, Demand Factors & Neutral Calculations 4.2 Service-Entrance Conductors & Service Disconnecting Means 4.3 Service Equipment Rating, Emergency Disconnects & Surge Protection

5 Chapter 5: Load Calculations

5.1 Standard Dwelling Unit Load Calculations 5.2 Optional Dwelling Unit Load Calculations 5.3 Commercial Load Calculations & Non-Dwelling Demands

6 Chapter 6: Conductors, Cables & Flexible Cords

6.1 Conductor Types, Insulation & Temperature Ratings 6.2 Conductor Ampacity Derating & Correction Factors 6.3 Nonmetallic-Sheathed Cable (Type NM) & Underground Feeder (Type UF) 6.4 Armored Cable (Type AC) & Metal-Clad Cable (Type MC) 6.5 Service-Entrance Cable (Types SE & USE), Other Cables & Flexible Cords

7 Chapter 7: Raceways, Conduit Fill & Enclosures

7.1 Conduit Systems: EMT, RMC, IMC, and PVC 7.2 Flexible Raceways: FMC, LFMC, and LFNC 7.3 Conduit Fill Calculations & Chapter 9 Tables 7.4 Outlet, Device & Junction Box Sizing 7.5 Wireways, Auxiliary Gutters, Surface Raceways & Cable Trays 7.6 Underground Raceways, ENT & Protection from Physical Damage

8 Chapter 8: Grounding & Bonding Systems

8.1 Grounding Electrode System & Grounding Electrodes 8.2 Grounding Electrode Conductor (GEC) Sizing & Installation 8.3 Main & System Bonding Jumpers 8.4 Equipment Grounding Conductors (EGC) Sizing & Identification

9 Chapter 9: Overcurrent Protection & Ground-Fault Protection

9.1 Standard Fuse & Circuit Breaker Ratings & Sizing 9.2 Small Conductor Rules & Overcurrent Exceptions 9.3 Tap Rules & Ground-Fault Protection of Equipment

10 Chapter 10: Motors, Motor Circuits & Transformers

10.1 Motor Conductor Sizing & Full-Load Current Tables 10.2 Motor Overload Protection 10.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 10.4 Transformer Sizing, Installation & Overcurrent Protection

11 Chapter 11: Special Occupancies, Hazardous Locations & Special Equipment

11.1 Hazardous (Classified) Locations: Class I, II, III 11.2 Healthcare Facilities & Patient Care Spaces 11.3 Swimming Pools, Spas & Hot Tubs 11.4 Agricultural Buildings, Mobile Homes, Marinas & RV Parks 11.5 Appliances, Electric Space Heating, Water Heaters & Special Equipment

12 Chapter 12: Lighting, Signs, Low Voltage, Communications & Safety

12.1 Luminaires, Lighting Outlets & Electric Signs 12.2 Fire Alarm Systems, Class 1, 2, 3 Circuits & Power-Limited Cables 12.3 Solar Photovoltaic (PV) & Energy Storage Systems 12.4 Electrical Safety, OSHA Regulations & NFPA 70E Fundamentals 12.5 Communications, CATV & Optical Fiber Systems (NEC Chapter 8) 12.6 OSHA Electrical Standards, Lockout/Tagout & Jobsite Safety

10.2 Motor Overload Protection

Key Takeaways Explain This Topic AI

Motor overload protection is engineered to protect motor windings, control apparatus, and branch-circuit conductors against excessive operating temperatures caused by motor overloads and failure to start, distinct from short-circuit protection.

Under NEC 430.6(A)(1) and NEC 430.32, motor overload protective devices must be sized strictly from the motor NAMEPLATE full-load current rating, never from NEC FLC tables.

Continuous-duty motors rated more than 1 HP with a marked service factor of 1.15 or greater, or a marked temperature rise of 40°C or less, permit overload protection sized up to 125 percent of nameplate current per NEC 430.32(A)(1).

All other continuous-duty motors greater than 1 HP (including motors with a 1.0 service factor or temperature rise over 40°C) must have overload protection sized at not more than 115 percent of nameplate current.

Under NEC 430.32(C), if standard overload devices trip during starting, modifications may increase ratings up to 140 percent for SF ≥ 1.15 / 40°C motors, and up to 130 percent for all other motors, while NEC 430.43 strictly prohibits automatic resets where unexpected restart creates hazards.

Last updated: September 2026

Motor Overload Protection

Motor circuits feature two distinct protective functions operating in series: overload protection and short-circuit/ground-fault protection. While short-circuit devices protect against catastrophic fault currents, motor overload protection safeguards the motor windings, control apparatus, and branch-circuit conductors against destructive thermal stress resulting from mechanical overloads, bearing friction, voltage unbalances, or failure to start. Governed by NEC Article 430 Part III , understanding overload sizing rules, service factor criteria, and reset mechanisms is vital for journeyman exam success.

1. Physics of Motor Overload vs. Short-Circuit Protection

An overload occurs when an operating motor draws currents in excess of its continuous full-load rating while remaining confined to normal conductor paths. Under sustained overloads—typically ranging from 1.15 × 1.15\times 1.15 × to 6 × 6\times 6 × rated current—internal winding temperatures rise exponentially in proportion to I 2 R t I^2 R t I 2 Rt . If sustained, this heat rapidly deteriorates winding varnish and insulation, cutting motor operating lifespan in half for every 10°C increase above thermal insulation limits (such as Class B, F, or H insulation).

Because motors draw high inrush currents upon starting (locked-rotor currents typically reach 600 % 600\% 600% of full-load current), the branch-circuit breaker or fuse must be sized high enough to permit starting without nuisance tripping. Consequently, the branch-circuit breaker cannot protect the motor against moderate overloads. That dedicated protective role falls entirely upon the motor overload device housed in the motor starter or controller.

2. Overload Protective Devices & Operating Technologies

Overload relays monitor current drawn by each phase and trigger an auxiliary contact that de-energizes the starter's magnetic coil when overheating is detected:

Bimetallic Thermal Overload Relays : Current passes through resistive heater elements positioned adjacent to a bonded bimetallic strip. As heat accumulates, the two metals expand at different rates, deflecting the strip until it mechanically unlatches a spring-loaded normally closed (NC) contact in the control circuit.

Melting Alloy (Eutectic Solder Pot) Relays : Motor current passes through a heater coil surrounding a small brass tube filled with a special eutectic alloy solder. Under excessive current, the solder melts sharply at a precise temperature, allowing a spring-loaded ratchet wheel to turn and trip the auxiliary control contacts. Once cooled, the solder resolidifies and can be manually reset.

Solid-State Electronic Overload Relays : Modern microprocessor-based relays use current transformers (CTs) to measure phase currents directly. They feature user-selectable trip classes:

Class 10 : Trips in 10 seconds or less at 600% locked-rotor current (ideal for fast-heating submersible pumps and hermetic compressors).

Class 20 : Trips in 20 seconds at 600% current (standard industrial T-frame motors).

Class 30 : Trips in 30 seconds at 600% current (high-inertia loads such as industrial flywheels and heavy blowers).

3. Sizing Overload Protection per NEC 430.32

Unlike conductors and fuses, NEC 430.6(A)(1) and NEC 430.32 dictate that motor overload protection must be sized using the actual motor NAMEPLATE full-load current , never the NEC tables. For continuous-duty motors rated more than 1 HP, NEC 430.32(A)(1) establishes two primary percentage tiers:

1. Motors Sized at Maximum 125% of Nameplate Current:

Motors with a marked Service Factor (SF) of 1.15 or greater .

Motors with a marked temperature rise of 40°C or less .

A Service Factor of 1.15 indicates the motor is engineered to handle a continuous 15 percent overload without exceeding insulation thermal damage limits.

2. Motors Sized at Maximum 115% of Nameplate Current:

All other motors , including any motor with a marked Service Factor of 1.0 or an unmarked service factor, and motors with a marked temperature rise exceeding 40°C. Standard Maximum Overload Setting = { Nameplate Current × 1.25 if SF ≥ 1.15 or Temp Rise ≤ 40 ∘ C Nameplate Current × 1.15 all other motors \text{Standard Maximum Overload Setting} = \begin{cases} \text{Nameplate Current} \times 1.25 & \text{if SF} \ge 1.15 \text{ or Temp Rise} \le 40^\circ\text{C} \\ \text{Nameplate Current} \times 1.15 & \text{all other motors} \end{cases} Standard Maximum Overload Setting = { Nameplate Current × 1.25 Nameplate Current × 1.15 ​ if SF ≥ 1.15 or Temp Rise ≤ 4 0 ∘ C all other motors ​

4. Maximum Overload Modification Exceptions (NEC 430.32(C))

In practical installations, high starting inertia or prolonged acceleration times may cause standard overload relays sized under 430.32(A)(1) to trip before the motor reaches full operating speed. Under NEC 430.32(C) , where the standard selected overload relay is insufficient to start the motor or carry the load, the next higher size overload device may be installed, provided the trip rating does not exceed the following statutory ceilings:

140 percent of nameplate full-load current for motors with a Service Factor ≥ 1.15 \ge 1.15 ≥ 1.15 or temperature rise ≤ 40 ∘ C \le 40^\circ\text{C} ≤ 4 0 ∘ C .

130 percent of nameplate full-load current for all other motors. Absolute Overload Modification Ceiling = { Nameplate Current × 1.40 if SF ≥ 1.15 or Temp Rise ≤ 40 ∘ C Nameplate Current × 1.30 all other motors \text{Absolute Overload Modification Ceiling} = \begin{cases} \text{Nameplate Current} \times 1.40 & \text{if SF} \ge 1.15 \text{ or Temp Rise} \le 40^\circ\text{C} \\ \text{Nameplate Current} \times 1.30 & \text{all other motors} \end{cases} Absolute Overload Modification Ceiling = { Nameplate Current × 1.40 Nameplate Current × 1.30 ​ if SF ≥ 1.15 or Temp Rise ≤ 4 0 ∘ C all other motors ​

5. Phase Overload Protection & Single-Phasing (NEC Table 430.37)

Under NEC Table 430.37 , three-phase AC motors must have three overload units —one sensing element installed in each ungrounded phase conductor. This universal requirement prevents catastrophic motor burnout under single-phasing conditions. If one phase opens on a 3-phase supply (such as a blown utility primary fuse), the motor will attempt to carry its mechanical load on the remaining two phases, drawing 1.732 × 1.732\times 1.732 × normal current and generating extreme thermal stress in the active stator coils.

6. Safety Rules: Manual vs. Automatic Reset Overloads (NEC 430.43)

Under NEC 430.43 , an overload device that resets automatically upon cooling is strictly prohibited if automatic restarting of the motor can result in personal injury to operators or maintenance personnel. For hazardous mechanical equipment—such as meat grinders, table saws, metal lathes, conveyor belts, and industrial punch presses—overload relays must require manual reset to guarantee that power cannot be restored until an operator deliberately clears the machine and pushes the start button.

7. Overload Protection Reference Summary

  • Parameter NEC Section Requirement / Maximum Rating
  • Current Source NEC 430.6(A)(1) Motor NAMEPLATE current only (never NEC tables)

Standard SF ≥ 1.15 \ge 1.15 ≥ 1.15 / ≤ 40 ∘ C \le 40^\circ\text{C} ≤ 4 0 ∘ C NEC 430.32(A)(1) 125 % 125\% 125% of nameplate full-load current

Standard All Other Motors NEC 430.32(A)(1) 115 % 115\% 115% of nameplate full-load current

Modification SF ≥ 1.15 \ge 1.15 ≥ 1.15 / ≤ 40 ∘ C \le 40^\circ\text{C} ≤ 4 0 ∘ C NEC 430.32(C) Absolute maximum of 140 % 140\% 140% of nameplate current

  • Modification All Other Motors NEC 430.32(C) Absolute maximum of 130 % 130\% 130% of nameplate current
  • Number of Overload Units NEC Table 430.37 3 units (one per phase) for all 3-phase AC motors
  • Automatic Reset Restriction NEC 430.43 Prohibited where restarting creates injury hazard
  • 8. Step-by-Step Worked Sizing Examples
  • Worked Example 1: 3-Phase Industrial Motor

A 15 HP, 460-volt, 3-phase induction motor has a marked nameplate current of 18.5 amperes and a marked service factor of 1.15. Determine the standard overload setting and the maximum allowable modified setting if starting difficulties occur.

Standard Overload Sizing (NEC 430.32(A)(1)) : Because the service factor is 1.15, use the 125 percent multiplier on the nameplate rating: Standard Maximum Overload = 18.5 A × 1.25 = 23.125 amperes \text{Standard Maximum Overload} = 18.5\text{ A} \times 1.25 = 23.125\text{ amperes} Standard Maximum Overload = 18.5 A × 1.25 = 23.125 amperes

Modified Overload Sizing (NEC 430.32(C)) : If the motor fails to accelerate to speed with a 23.1A heater, an increased heater is permitted up to 140 percent: Maximum Modified Overload = 18.5 A × 1.40 = 25.90 amperes \text{Maximum Modified Overload} = 18.5\text{ A} \times 1.40 = 25.90\text{ amperes} Maximum Modified Overload = 18.5 A × 1.40 = 25.90 amperes

Worked Example 2: Motor with 1.0 Service Factor

A 7.5 HP, 230-volt single-phase air compressor motor has a marked nameplate current of 38.0 amperes, a service factor of 1.0, and a temperature rise of 50°C.

Standard Overload Sizing : Because the service factor is 1.0 (less than 1.15) and temperature rise exceeds 40°C, the motor falls into the 115 percent category: Standard Maximum Overload = 38.0 A × 1.15 = 43.70 amperes \text{Standard Maximum Overload} = 38.0\text{ A} \times 1.15 = 43.70\text{ amperes} Standard Maximum Overload = 38.0 A × 1.15 = 43.70 amperes

Modified Overload Sizing : If needed under NEC 430.32(C), the maximum allowable rating is 130 percent: Maximum Modified Overload = 38.0 A × 1.30 = 49.40 amperes \text{Maximum Modified Overload} = 38.0\text{ A} \times 1.30 = 49.40\text{ amperes} Maximum Modified Overload = 38.0 A × 1.30 = 49.40 amperes