ExamFinch.com My Study

Study guide

2.6 Risk Management, Contractor Insurance & Surety Bonds

Practice this exam

Alabama HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Alabama HACR Laws, Rules & Licensing

1.1 Alabama HACR Board Authority, Licensing Pathways & Experience Requirements 1.2 Contractor Bonding, Insurance, Fees & Annual Renewal 1.3 Permits, Local Jurisdictions, Inspections & Disciplinary Actions

2 Contractor Business, Contracts, Estimating & Alabama Lien Law

2.1 Business Organization, Risk Management & Project Administration 2.2 Construction Contracts, Change Orders & Warranties 2.3 Alabama Mechanics' Lien Law & Financial Management 2.4 Construction Estimating, Markup & Bid Preparation 2.5 Project Management, Scheduling & Field Supervision 2.6 Risk Management, Contractor Insurance & Surety Bonds

3 Safety Standards, OSHA & EPA Section 608

3.1 OSHA Construction Safety (29 CFR 1926) for HVAC Contractors 3.2 EPA Section 608 Refrigerant Regulations & Recovery Requirements 3.3 Refrigerant Management, Leak Repair Rules & A2L Transition

4 General Technical Knowledge & Thermodynamics

4.1 Principles of Heat Transfer, Temperature & Pressure 4.2 The Mechanical Refrigeration Cycle & Refrigerant Properties 4.3 Psychrometrics & Air Properties for Humid Climates 4.4 Basic Electricity, Ohm's Law & Electrical Power for HVAC

5 Piping Systems, Refrigerant Lines & Fuel Gas Piping

5.1 Refrigerant Piping Sizing, Materials & Installation 5.2 Fuel Gas Piping Sizing & Installation (IRC Chapter 24) 5.3 Condensate Drain Systems & Trapping

6 System Sizing & ACCA Manual J Load Calculations

6.1 ACCA Manual J Fundamentals & Design Conditions 6.2 Envelope Loads: Conduction, Radiation & Fenestration 6.3 Infiltration, Ventilation & Internal Heat Gains

7 Duct System Design & ACCA Manual D

7.1 Airflow Principles, Static Pressure & Fan Performance 7.2 ACCA Manual D Duct Sizing & Friction Rate 7.3 Duct Materials, Installation Standards & Air Distribution

8 Heating & Cooling Equipment Operation

8.1 Heat Pump Systems & Supplemental Heating 8.2 Gas Furnaces & Combustion Systems 8.3 Air Conditioning Units, Compressors & Metering Devices

9 Mechanical Codes, Electrical Applications & Maintenance Diagnostics

9.1 Combustion Air & Venting Systems (IRC Chapter 24) 9.2 Electrical Applications for HVAC (NFPA 70 / NEC Article 440) 9.3 Preventative Maintenance, Troubleshooting & Plan Reading

10 Employment Law, Payroll Taxes & Contractor Finance

10.1 Federal & Alabama Labor Laws for HVAC Employers 10.2 Payroll, Employment Taxes & Worker Classification 10.3 Job Costing, Break-Even Analysis & Cash Flow Forecasting

11 Preventative Maintenance, Service Procedures & Commissioning

11.1 Preventative Maintenance Programs & Service Agreements 11.2 Filter, Coil & Drain Maintenance for Alabama's Humid Climate 11.3 Evacuation, Dehydration & Refrigerant Charging Procedures 11.4 Airflow Verification, Static Pressure Testing & Commissioning

12 Electrical Applications & Construction Documents

12.1 Electric Motors, Compressors & Motor Protection 12.2 Transformers, Control Circuits & Low-Voltage Wiring 12.3 Branch Circuits, Conductors, Grounding & Disconnects 12.4 Construction Documents, Specifications & Submittals

2.6 Risk Management, Contractor Insurance & Surety Bonds

Key Takeaways Explain This Topic AI

The four risk treatments are avoid, transfer, mitigate, and retain; insurance and indemnity clauses are transfer tools, and a safety program is a mitigation tool.

Alabama requires workers compensation coverage from employers who regularly employ five or more employees, and corporate officers count toward the five.

A commercial general liability policy carries both a per-occurrence limit and a separate annual aggregate, and products-completed operations coverage is what responds after the job is finished.

A surety bond is a three-party credit instrument, and the surety has a right of indemnity to recover every dollar it pays from the contractor.

Code of Alabama Section 39-1-1 requires a payment bond of not less than 50 percent of the contract price on public works, because a mechanics lien cannot attach to public property.

Last updated: September 2026

2.6 Risk Management, Contractor Insurance & Surety Bonds

Important

Bond versus insurance : This is the single distinction the risk management questions return to. Insurance is a two-party contract in which the insurer expects to pay losses and prices premiums to cover them. A surety bond is a three-party credit instrument in which the surety expects to pay nothing, and when it does pay it has a contractual right of indemnity to recover the full amount from the contractor. A bond protects the owner; only insurance protects the contractor.

The Four Treatments of Risk

  • Treatment Meaning HVAC example
  • Avoid Decline the exposure entirely Refusing asbestos-abatement scope on a duct demolition

Transfer Move the financial consequence to another party Insurance, indemnity clauses, subcontracting specialty work

  • Mitigate Reduce frequency or severity Fall protection program, torch-free press fittings, lockout/tagout
  • Retain Accept and fund it Deductibles, self-insured tool losses, a contingency line in the estimate

Every risk gets one of these four answers. "We will be careful" is not one of them.

  • The Contractor Insurance Portfolio
  • Commercial General Liability (CGL)

The foundation policy. It responds to third-party bodily injury and property damage caused by the contractor operations.

Occurrence versus claims-made : an occurrence form covers injury that happens during the policy period no matter when the claim is filed. A claims-made form covers only claims reported while the policy (or its extended reporting period) is active. Construction buyers should insist on occurrence form.

Two limits, not one : a policy written at $1,000,000 / $2,000,000 pays up to $1,000,000 for any single occurrence and no more than $2,000,000 for all occurrences in the policy year. A second large loss in the same year can exhaust the aggregate.

Products-completed operations : the part of the CGL that responds after the work is finished and turned over. A flue that leaks carbon monoxide two months after start-up is a completed-operations claim. Contractors who let this coverage lapse are uninsured for their installed work.

Common exclusions : damage to the contractor own work (the "your work" exclusion), professional liability for design, pollution, and employee injury (which belongs to workers compensation).

Workers Compensation - the Alabama Threshold

Under the Alabama Workers Compensation Act, Code of Alabama Title 25, Chapter 5, an employer who regularly employs five or more employees in any one business must secure coverage. Key exam points:

Full-time, part-time, and seasonal employees all count toward the five, and corporate officers are counted as employees for the threshold.

Coverage is the exclusive remedy : an injured employee recovers statutory benefits and generally may not sue the employer in tort.

The experience modification rate (EMR) multiplies the manual premium. An EMR of 1.00 is industry average; 0.80 means the contractor pays 20% less than average, and many general contractors and owners will not let a subcontractor on site with an EMR above 1.00.

A contractor who hires an uninsured subcontractor can be treated as the statutory employer of that subcontractor employees, which is why certificates of insurance are collected before the sub starts work, not after.

The Rest of the Portfolio

  • Policy What it covers
  • Commercial auto Service trucks, owned, hired, and non-owned vehicles
  • Inland marine / tools and equipment Recovery machines, gauges, vacuum pumps, brakes, in transit and on site
  • Builders risk Physical damage to the work in progress, usually owner- or GC-purchased
  • Umbrella / excess Additional limit sitting above CGL, auto, and employers liability
  • Employment practices liability (EPLI) Wrongful termination, harassment, discrimination claims
  • Cyber Customer data breach in the dispatch and payment system
  • Certificates, Additional Insured and Waivers

A certificate of insurance (COI) is evidence only; it grants no coverage. The coverage comes from the policy and its endorsements.

Additional insured status must be added by endorsement. Being listed only in the certificate description box is worth nothing in a coverage fight.

A waiver of subrogation stops the contractor insurer from suing the owner or general contractor after paying a loss. It must be endorsed onto the policy, and it usually costs a small additional premium.

Indemnity / hold harmless clauses shift liability by contract. Read them for scope: a broad-form clause that makes you indemnify the owner for the owner own negligence may be unenforceable or uninsurable.

Surety Bonds

A bond has three parties: the principal (the contractor), the obligee (the party protected), and the surety (the company guaranteeing performance).

  • Bond Purpose
  • Bid bond Guarantees the bidder will enter the contract and furnish final bonds if awarded
  • Performance bond Guarantees completion according to the contract documents
  • Payment bond Guarantees payment to subcontractors, laborers, and suppliers
  • Maintenance / warranty bond Guarantees correction of defects during the warranty term
  • License bond Required by a regulator - in Alabama, the $20,000 HACR Form BF-1 performance bond

Underwriting turns on the "three Cs": capital (working capital and net worth), capacity (the ability to perform the work), and character (payment history and references). Reviewed or audited financial statements, a work-in-progress schedule, and personal indemnity agreements from the owners are standard.

Public Work in Alabama

A mechanics lien cannot attach to public property . Alabama replaces that remedy with a statutory bond. Code of Alabama Section 39-1-1 requires a contractor on a public works contract to execute a performance bond and, separately, a payment bond in an amount not less than 50 percent of the contract price , payable to the awarding authority, guaranteeing payment to everyone supplying labor, materials, or supplies, and covering reasonable attorney fees for successful claimants. A claimant may not file suit on the bond until 45 days after written notice to the surety stating the amount and nature of the claim, and the action must generally be brought within one year of project completion. Missing the notice step, not the lien deadline, is what defeats most Alabama public-project claims.