Study guide

12.2 Transformers, Control Circuits & Low-Voltage Wiring

Alabama HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Alabama HACR Laws, Rules & Licensing

1.1 Alabama HACR Board Authority, Licensing Pathways & Experience Requirements 1.2 Contractor Bonding, Insurance, Fees & Annual Renewal 1.3 Permits, Local Jurisdictions, Inspections & Disciplinary Actions

2 Contractor Business, Contracts, Estimating & Alabama Lien Law

2.1 Business Organization, Risk Management & Project Administration 2.2 Construction Contracts, Change Orders & Warranties 2.3 Alabama Mechanics' Lien Law & Financial Management 2.4 Construction Estimating, Markup & Bid Preparation 2.5 Project Management, Scheduling & Field Supervision 2.6 Risk Management, Contractor Insurance & Surety Bonds

3 Safety Standards, OSHA & EPA Section 608

3.1 OSHA Construction Safety (29 CFR 1926) for HVAC Contractors 3.2 EPA Section 608 Refrigerant Regulations & Recovery Requirements 3.3 Refrigerant Management, Leak Repair Rules & A2L Transition

4 General Technical Knowledge & Thermodynamics

4.1 Principles of Heat Transfer, Temperature & Pressure 4.2 The Mechanical Refrigeration Cycle & Refrigerant Properties 4.3 Psychrometrics & Air Properties for Humid Climates 4.4 Basic Electricity, Ohm's Law & Electrical Power for HVAC

5 Piping Systems, Refrigerant Lines & Fuel Gas Piping

5.1 Refrigerant Piping Sizing, Materials & Installation 5.2 Fuel Gas Piping Sizing & Installation (IRC Chapter 24) 5.3 Condensate Drain Systems & Trapping

6 System Sizing & ACCA Manual J Load Calculations

6.1 ACCA Manual J Fundamentals & Design Conditions 6.2 Envelope Loads: Conduction, Radiation & Fenestration 6.3 Infiltration, Ventilation & Internal Heat Gains

7 Duct System Design & ACCA Manual D

7.1 Airflow Principles, Static Pressure & Fan Performance 7.2 ACCA Manual D Duct Sizing & Friction Rate 7.3 Duct Materials, Installation Standards & Air Distribution

8 Heating & Cooling Equipment Operation

8.1 Heat Pump Systems & Supplemental Heating 8.2 Gas Furnaces & Combustion Systems 8.3 Air Conditioning Units, Compressors & Metering Devices

9 Mechanical Codes, Electrical Applications & Maintenance Diagnostics

9.1 Combustion Air & Venting Systems (IRC Chapter 24) 9.2 Electrical Applications for HVAC (NFPA 70 / NEC Article 440) 9.3 Preventative Maintenance, Troubleshooting & Plan Reading

10 Employment Law, Payroll Taxes & Contractor Finance

10.1 Federal & Alabama Labor Laws for HVAC Employers 10.2 Payroll, Employment Taxes & Worker Classification 10.3 Job Costing, Break-Even Analysis & Cash Flow Forecasting

11 Preventative Maintenance, Service Procedures & Commissioning

11.1 Preventative Maintenance Programs & Service Agreements 11.2 Filter, Coil & Drain Maintenance for Alabama's Humid Climate 11.3 Evacuation, Dehydration & Refrigerant Charging Procedures 11.4 Airflow Verification, Static Pressure Testing & Commissioning

12 Electrical Applications & Construction Documents

12.1 Electric Motors, Compressors & Motor Protection 12.2 Transformers, Control Circuits & Low-Voltage Wiring 12.3 Branch Circuits, Conductors, Grounding & Disconnects 12.4 Construction Documents, Specifications & Submittals

12.2 Transformers, Control Circuits & Low-Voltage Wiring

Key Takeaways Explain This Topic AI

A control transformer is rated in volt-amperes, and the sum of the connected load VA - contactor coils, relays, valves, and the thermostat - must not exceed that rating.

The transformer turns ratio equals the voltage ratio, so a 240 to 24 volt transformer has a 10 to 1 ratio and steps current up by the same factor on the secondary.

A Class 2 control circuit under NEC Article 725 is limited in both voltage and power, which is why 24 volt control wiring is not required to be run in raceway like line-voltage conductors.

The standard low-voltage color code is R for 24 volt hot, C for common, Y for cooling, G for indoor fan, W for heat, and O or B for the heat pump reversing valve.

A control circuit fault is isolated by measuring 24 volts to common at each successive terminal, which locates the open device rather than guessing at the sequence.

Last updated: September 2026

12.2 Transformers, Control Circuits & Low-Voltage Wiring

Important

Nearly every no-heat and no-cool call is a control-circuit call. Line-voltage components fail loudly and rarely; 24 volt circuits fail quietly and constantly. The method in this section - measure to common at each successive terminal - resolves them without guesswork.

How a Transformer Works

A transformer has no moving parts. Alternating current in the primary winding creates a changing magnetic field in a laminated iron core, and that changing field induces a voltage in the secondary winding. Direct current will not work, because a steady field induces nothing.

Turns Ratio E primary E secondary = N primary N secondary = I secondary I primary \frac{E_{\text{primary}}}{E_{\text{secondary}}} = \frac{N_{\text{primary}}}{N_{\text{secondary}}} = \frac{I_{\text{secondary}}}{I_{\text{primary}}} E secondary ​ E primary ​ ​ = N secondary ​ N primary ​ ​ = I primary ​ I secondary ​ ​

A 240-volt to 24-volt transformer has a 10 to 1 turns ratio. Voltage steps down by 10; current steps up by 10. Power in equals power out, less core and winding losses.

VA Rating and Load Budgeting

Control transformers are rated in volt-amperes (VA) , and the sum of the connected loads must not exceed the rating.

  • Load Typical sealed VA draw
  • Contactor coil (residential condenser) 8 to 12 VA
  • Fan relay coil 4 to 8 VA
  • Gas valve 10 to 15 VA
  • Zone damper motor 5 to 10 VA
  • Communicating thermostat 3 to 6 VA
  • Humidifier solenoid 8 to 12 VA

A 40 VA transformer carrying a contactor, a fan relay, a gas valve, and a humidifier is at or beyond capacity. Note that inrush current when a contactor coil first energizes is several times its sealed draw, which is why a marginal transformer will buzz, run hot, and eventually fail open.

Multi-Tap Primaries and Secondary Grounding

Most HVAC transformers have multi-tap primaries - commonly 120, 208, and 240 volts. Landing the 240-volt supply on the 208-volt tap over-fluxes the core and burns the transformer; landing 208 on the 240 tap produces a weak 21-volt secondary that will not reliably pull in a contactor.

One leg of the 24-volt secondary is normally bonded to the equipment chassis and becomes common (C) . That is why touching R to the cabinet produces a short.

Paralleling two transformers requires matched polarity. If the secondaries are out of phase they oppose each other and both transformers burn.

Class 2 Control Circuits

NEC Article 725 classifies remote-control and signaling circuits. A Class 2 circuit is limited in voltage and power so that it presents minimal shock and fire-initiation hazard - which is why 24-volt thermostat wire may be run without raceway or cable armor, and why it may not be run in the same raceway or enclosure as line-voltage conductors unless a barrier or listed method separates them. The transformer or power supply itself must be a listed Class 2 source; that listing, not the wire, is what makes the circuit Class 2.

The Thermostat Color Code and What Each Wire Does

  • Terminal Conventional color Function
  • R / Rh / Rc Red 24 volt hot from the transformer
  • C Blue or brown 24 volt common; required by nearly all modern thermostats for power
  • Y / Y2 Yellow Compressor contactor, first and second stage
  • G Green Indoor blower relay
  • W / W2 White Heat, first and second stage or auxiliary heat
  • O / B Orange / dark blue Heat pump reversing valve energized in cooling (O) or in heating (B)
  • S1 / S2 Varies Outdoor temperature sensor
  • L Varies Malfunction or defrost indicator

Warning

O versus B is a heat pump trap. Most manufacturers energize the reversing valve in cooling , which is the O terminal. A minority energize it in heating , which is the B terminal. Wire it to the wrong terminal and the system delivers heat when the thermostat calls for cooling. Confirm against the equipment wiring diagram, never against habit.

A Simple Cooling Sequence

The thermostat closes R to G , energizing the indoor fan relay.

The thermostat closes R to Y , energizing the compressor contactor coil.

The contactor pulls in, closing line-voltage contacts to the compressor and condenser fan.

On a heat pump in cooling, R to O energizes the reversing valve solenoid.

Every safety in the circuit - the low-pressure switch, the high-pressure switch, the float switch - is wired in series in that low-voltage path, so any one of them opening drops the contactor out.

Relays, Contactors and Sequencers

A relay uses a low-power coil to switch a separate circuit. Contacts are described as normally open (NO) or normally closed (NC) , always with the coil de-energized.

A contactor is a heavy-duty relay sized to switch motor loads, rated in amperes and by pole count. Pitted or welded contacts cause chattering, voltage drop across the contacts, and compressor overheating.

A sequencer on electric strip heat closes its contacts in timed stages after its heater element warms, so the strips do not all inrush at once.

A defrost board on a heat pump uses time and temperature to initiate and terminate defrost, energizing the reversing valve, stopping the outdoor fan, and bringing on auxiliary heat during the cycle.

Low-Voltage Wire Sizing

Thermostat cable is normally 18 AWG solid conductor. On long runs the voltage drop becomes real: 18 AWG has roughly 6.4 ohms per 1,000 feet, so a 150-foot run carries about 300 feet of conductor and near 2 ohms of loop resistance. At a 0.5 ampere control load that is a 1-volt drop - tolerable. Double the load or the distance and the contactor may chatter or fail to pull in. On runs over about 100 feet with multiple loads, step up to 16 AWG.

Troubleshooting a Dead Control Circuit

Work from the source outward, always measuring to common :

Confirm line voltage at the transformer primary.

Measure the secondary: 24 to 28 volts across R and C confirms the transformer.

If the secondary is dead, look for a shorted low-voltage conductor, a shorted valve or coil, or an open fuse. Many boards use a 3 or 5 ampere automotive-style blade fuse on the 24 volt circuit; a blown fuse means a short exists and must be found before the fuse is replaced.

With the secondary confirmed, measure R to C at each successive terminal and safety device with a call energized. The first place the 24 volts disappears is the open device.

Confirm the coil, not the contacts, when a contactor fails to pull in - measure 24 volts across the coil terminals and check coil resistance with power off.