Study guide
2.1 Minimum Plumbing Facilities, Fixture Clearances & Accessibility
Alabama Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Alabama Law, General Regulations, Trade Math, Tools & Safety
1.1 Alabama Exam Format, Licensing Law & Board Rules 1.2 IPC Chapter 3 General Regulations: Protection, Sleeves, Trenching & Structural Safety 1.3 Trade Math I: Pressure, Head, Fall, Volume & Expansion 1.4 Trade Math II: Fractions, Offsets, Areas & Heat Calculations 1.5 Plumbing Tools: Layout, Cutting, Joining, Threading & Test Equipment 1.6 Jobsite Safety: Trenches, Ladders, Confined Spaces, Hot Work & PPE
2 Chapter 2: Plumbing Fixtures, Fittings & Clearances
2.1 Minimum Plumbing Facilities, Fixture Clearances & Accessibility 2.2 Fixture Materials, Prohibited Fixtures, Overflows, Waste Outlets & Fixture Setting 2.3 Flushing Devices, Water Conservation & Temperature-Limiting Controls
3 Chapter 3: Water Supply, Distribution, Backflow & Water Heaters
3.1 Water Service & Distribution Sizing: WSFU, Demand, Pressure & Friction 3.2 Water Piping Materials, Joints, Valves, Supports & Disinfection 3.3 Cross-Connection Control & Backflow Prevention (IPC 608 & 312.10) 3.4 Water Heaters: Installation, Relief Valves, Pans & Thermal Expansion
4 Chapter 4: Sanitary Drainage Systems & DWV Sizing
4.1 Drainage Fixture Units & Sizing Branches, Stacks and Building Drains 4.2 Drainage Slopes, Building Drain & Sewer Rules, Offsets and Backwater Valves 4.3 DWV Materials, Fittings, Joints, Supports & Underground Installation 4.4 Indirect Waste, Special Waste, Sumps and Sewage Ejectors
5 Chapter 5: Traps, Cleanouts, Interceptors & Separators
5.1 Fixture Traps, Trap Seals, Prohibited Traps & Trap Seal Protection 5.2 Cleanouts: Required Locations, Size, Arrangement, Clearance & Access 5.3 Grease Interceptors, Oil Separators & Other Interceptors (IPC 1003)
6 Chapter 6: Vents and Venting Methods
6.1 Vent Purpose, Vent Stacks, Connections, Terminals & Vent Sizing 6.2 Fixture Vents, Individual Vents, Common Vents & Wet Venting 6.3 Circuit Vents, Combination Waste & Vent, Island, Waste Stack & Single-Stack Venting 6.4 Air Admittance Valves: Standards, Where Permitted, Location & Prohibitions
7 Chapter 7: Plan Reading, Sizing Practice, Testing & Fuel Gas
7.1 Reading Plumbing Drawings, Isometrics, Symbols & Schedules 7.2 Plan-Based Sizing Practice: Branches, Stacks, Building Drain, Vents & Water 7.3 Inspections and Tests: DWV, Water, Sewers, Storm, Shower Pans & Backflow 7.4 Fuel Gas Basics, Combustion Air, Venting & Alabama Gas Fitting Scope
8 Chapter 8: Roof Drain & Storm Drainage Systems
8.1 Roof Drains, Rainfall Rates & Storm Drain Sizing (IPC 1101–1106) 8.2 Secondary (Emergency) Roof Drainage, Scuppers, Controlled Flow, Subsoil Drains & Storm Sumps
2.1 Minimum Plumbing Facilities, Fixture Clearances & Accessibility
Key Takeaways Explain This Topic AI
IPC 403.1.1 divides the total occupant load in half for each sex, applies each Table 403.1 ratio, and rounds any fraction up to the next whole fixture.
A Group B office needs 1 water closet per 25 for the first 50 and 1 per 50 for the rest of each sex, and 1 lavatory per 40 for the first 80 and 1 per 80 for the rest.
Urinals may replace up to 67% of required water closets in assembly and educational occupancies and up to 50% in all others (IPC 424.2).
IPC 405.3.1 requires at least 15 inches from a fixture's centerline to a side wall, 30 inches center to center between unpartitioned fixtures, and 21 inches of clearance in front.
Water closet compartments must be at least 30 inches wide and 60 inches deep for floor-mounted bowls or 56 inches deep for wall-hung bowls (IPC 405.3.1).
Last updated: October 2026
Why this section matters
Fixtures and Fittings carries 6 questions, and fixture counts also show up in plan-reading problems. The 2021 IPC puts minimum fixture counts in Table 403.1 . It sets clearances in 405.3 . Accessibility requirements come from the IBC and ICC A117.1 (IPC 404).
Counting fixtures with Table 403.1
The occupant load comes from the International Building Code . IPC 403.1.1 then works like this:
Divide the total occupant load in half to get the load for each sex. The exceptions are approved statistics showing a different split, all-gender multi-user rooms (counted at 100% of the load), and single-user rooms.
Apply each ratio to each sex separately , using Table 403.1.
Round any fraction up to the next whole number. For a building with mixed occupancies, add the fractions for each occupancy first, then round.
Selected rows from Table 403.1:
- Occupancy Water closets (M / F) Lavatories Drinking fountains Other
- A-1 theaters 1 per 125 / 1 per 65 1 per 200 1 per 500 1 service sink
- A-2 restaurants and banquet halls 1 per 75 / 1 per 75 1 per 200 1 per 500 1 service sink
- A-2 nightclubs and bars 1 per 40 / 1 per 40 1 per 75 1 per 500 1 service sink
- A-3 places of worship 1 per 150 / 1 per 75 1 per 200 1 per 1,000 1 service sink
B business (offices, banks) 1 per 25 for the first 50, then 1 per 50 1 per 40 for the first 80, then 1 per 80 1 per 100 1 service sink
- E educational 1 per 50 1 per 50 1 per 100 1 service sink
- F factory and industrial 1 per 100 1 per 100 1 per 400 1 service sink
- M mercantile (retail) 1 per 500 1 per 750 1 per 1,000 1 service sink
- S storage 1 per 100 1 per 100 1 per 1,000 1 service sink
Business and mercantile spaces with 15 or fewer occupants do not need a service sink.
Separate facilities and single-user rooms
403.2: Where fixtures are required, provide separate facilities for each sex. There are exceptions:
- dwelling and sleeping units;
- spaces with 15 or fewer total occupants;
- mercantile occupancies of 100 or fewer ;
- business occupancies of 25 or fewer ;
- single-user rooms;
all-gender rooms that give water closets privacy (405.3.4) and place each urinal in a stall or visually separated area.
403.1.2: Fixtures in single-user and family or assisted-use toilet rooms count toward the required total. These rooms must be identified as usable by all persons regardless of sex. Where several single-user rooms are clustered, at least one must have baby-changing facilities.
Urinal substitution (424.2)
In each toilet room, urinals may replace no more than 67% of the required water closets in assembly and educational occupancies, and no more than 50% in all other occupancies. Urinals substitute for water closets. They are not extra fixtures added on top of the required count.
Location and access (403.3)
Required public and employee facilities must be no more than one story above or below the space they serve, with a travel path of no more than 500 feet . In malls, the limit is 300 feet .
The route to public toilet rooms may not pass through kitchens, storage rooms or closets .
Toilet rooms may not open directly into a room where food is prepared for the public.
A multi-occupant toilet room's door may not be lockable from inside (403.3.6).
Worked example: two-story office
A Group B office has an occupant load of 120 (from the IBC).
Per sex: 120 ÷ 2 = 60 120 \div 2 = 60 120 ÷ 2 = 60 .
Water closets per sex: the first 50 need 50 ÷ 25 = 2 50 \div 25 = 2 50 ÷ 25 = 2 . The remaining 10 need 10 ÷ 50 = 0.2 10 \div 50 = 0.2 10 ÷ 50 = 0.2 , which rounds up to 1. Total: 3 per sex .
Urinals: in the men's room, up to 50% of the 3 water closets may be urinals. Half of 3 is 1.5, and since substitution may not exceed 50%, that means 1 urinal plus 2 water closets .
Lavatories per sex: all 60 fall within the first 80, so 60 ÷ 40 = 1.5 60 \div 40 = 1.5 60 ÷ 40 = 1.5 , which rounds up to 2 per sex .
Drinking fountains: the column is not split by sex, so 120 ÷ 100 = 1.2 120 \div 100 = 1.2 120 ÷ 100 = 1.2 , which rounds up to 2 . One hi-lo unit with two spouts counts as the required pair (410.3.1).
Service sink: 1 .
Fixture clearances (405.3.1)
- Dimension Minimum
- Fixture centerline to side wall, partition or vanity (water closet, urinal, lavatory, bidet) 15 in
- Center to center of adjacent fixtures not separated by partitions 30 in
- Clearance in front of the fixture to any wall, fixture or door 21 in
- Water closet compartment, floor-mounted bowl 30 in wide × 60 in deep
- Water closet compartment, wall-hung bowl 30 in wide × 56 in deep
- Accessible children's water closet, centerline to wall on one side 12 in
405.3.4: Each public or employee water closet needs its own compartment with a door, except in a lockable single-occupant room.
405.3.5: Urinal partitions must leave at least 30 inches between walls at each urinal. They start no higher than 12 inches above the floor, rise to at least 60 inches , and project at least 18 inches from the wall or 6 inches past the urinal's front lip, whichever is greater.
405.3.2: In employee and public toilet rooms, the required lavatory must be in the same room as the required water closet.
Accessible fixtures (IPC 404 and ICC A117.1)
- Item Typical A117.1 dimension
- Water closet centerline from side wall 16 to 18 in (17 to 19 in in an ambulatory stall)
- Water closet seat height 17 to 19 in above floor
- Clear space at water closet 60 in measured perpendicular from the side wall × 56 in from the rear wall
- Side grab bar 42 in long minimum, 12 in maximum from the rear wall, extends 54 in minimum from the rear wall
- Rear grab bar 36 in long minimum, 12 in on the wall side of the centerline, 24 in on the open side
- Grab bar height 33 to 36 in to the top of the gripping surface
- Flush control On the open side of the water closet, 48 in maximum height
- Lavatory rim or counter 34 in maximum
- Knee clearance 27 in high minimum, 30 in wide, at least 8 in deep at 27 in high
- Urinal rim (wall-hung) 17 in maximum above floor
- Wheelchair drinking fountain spout 36 in maximum; standing fountain spout 38 to 43 in
IPC 404.3: Water supply and drain pipes under accessible lavatories and sinks must be covered or otherwise configured to protect against contact. Pipe covers must comply with ASME A112.18.9 or ASTM C1822.
Drinking fountains (410)
No drinking fountain is required for an occupant load of 15 or fewer (410.2).
Where fountains are provided on a floor, on an exterior site or in a secured area, provide at least two : one for wheelchair users and one for standing persons. A single unit with two spouts may substitute (410.3.1).
Restaurants that serve free water in containers do not need fountains. In other occupancies where three or more fountains are required, water dispensers may replace up to 50% of them (410.4).
Fountains may not be installed in public restrooms (410.5).
Exam traps
Round per sex, then per fixture type. Do not combine fractions across sexes.
Urinal limit: 67% only for A and E occupancies. Everything else is 50%.
15-inch vs. 16- to 18-inch centerlines: 15 inches is the general IPC minimum. Accessible water closets are 16 to 18 inches.
Drinking fountains are never in the restroom.