Study guide

1.2 IPC Chapter 3 General Regulations: Protection, Sleeves, Trenching & Structural Safety

Alabama Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Alabama Law, General Regulations, Trade Math, Tools & Safety

1.1 Alabama Exam Format, Licensing Law & Board Rules 1.2 IPC Chapter 3 General Regulations: Protection, Sleeves, Trenching & Structural Safety 1.3 Trade Math I: Pressure, Head, Fall, Volume & Expansion 1.4 Trade Math II: Fractions, Offsets, Areas & Heat Calculations 1.5 Plumbing Tools: Layout, Cutting, Joining, Threading & Test Equipment 1.6 Jobsite Safety: Trenches, Ladders, Confined Spaces, Hot Work & PPE

2 Chapter 2: Plumbing Fixtures, Fittings & Clearances

2.1 Minimum Plumbing Facilities, Fixture Clearances & Accessibility 2.2 Fixture Materials, Prohibited Fixtures, Overflows, Waste Outlets & Fixture Setting 2.3 Flushing Devices, Water Conservation & Temperature-Limiting Controls

3 Chapter 3: Water Supply, Distribution, Backflow & Water Heaters

3.1 Water Service & Distribution Sizing: WSFU, Demand, Pressure & Friction 3.2 Water Piping Materials, Joints, Valves, Supports & Disinfection 3.3 Cross-Connection Control & Backflow Prevention (IPC 608 & 312.10) 3.4 Water Heaters: Installation, Relief Valves, Pans & Thermal Expansion

4 Chapter 4: Sanitary Drainage Systems & DWV Sizing

4.1 Drainage Fixture Units & Sizing Branches, Stacks and Building Drains 4.2 Drainage Slopes, Building Drain & Sewer Rules, Offsets and Backwater Valves 4.3 DWV Materials, Fittings, Joints, Supports & Underground Installation 4.4 Indirect Waste, Special Waste, Sumps and Sewage Ejectors

5 Chapter 5: Traps, Cleanouts, Interceptors & Separators

5.1 Fixture Traps, Trap Seals, Prohibited Traps & Trap Seal Protection 5.2 Cleanouts: Required Locations, Size, Arrangement, Clearance & Access 5.3 Grease Interceptors, Oil Separators & Other Interceptors (IPC 1003)

6 Chapter 6: Vents and Venting Methods

6.1 Vent Purpose, Vent Stacks, Connections, Terminals & Vent Sizing 6.2 Fixture Vents, Individual Vents, Common Vents & Wet Venting 6.3 Circuit Vents, Combination Waste & Vent, Island, Waste Stack & Single-Stack Venting 6.4 Air Admittance Valves: Standards, Where Permitted, Location & Prohibitions

7 Chapter 7: Plan Reading, Sizing Practice, Testing & Fuel Gas

7.1 Reading Plumbing Drawings, Isometrics, Symbols & Schedules 7.2 Plan-Based Sizing Practice: Branches, Stacks, Building Drain, Vents & Water 7.3 Inspections and Tests: DWV, Water, Sewers, Storm, Shower Pans & Backflow 7.4 Fuel Gas Basics, Combustion Air, Venting & Alabama Gas Fitting Scope

8 Chapter 8: Roof Drain & Storm Drainage Systems

8.1 Roof Drains, Rainfall Rates & Storm Drain Sizing (IPC 1101–1106) 8.2 Secondary (Emergency) Roof Drainage, Scuppers, Controlled Flow, Subsoil Drains & Storm Sumps

1.2 IPC Chapter 3 General Regulations: Protection, Sleeves, Trenching & Structural Safety

Key Takeaways Explain This Topic AI

IPC 305.6 requires 0.0575-inch (No. 16 gage) steel shield plates where concealed piping, other than cast iron or galvanized steel, is less than 1-1/4 inches from the edge of a framing member.

IPC 305.3 requires a relieving arch or a sleeve two pipe sizes larger where a pipe passes through a foundation wall, so a 4-inch sewer needs a 6-inch sleeve.

IPC 306.2.2 requires rock to be removed at least 3 inches below the pipe and replaced with tamped sand, and 306.3 requires backfill in 6-inch layers to 12 inches over the crown.

IPC 307.4 forbids cutting, drilling or notching truss members without written approval from a registered design professional.

IPC 314.2.1.1 forbids connecting condensate drains directly to a DWV pipe; they must discharge to a receptor such as a floor drain, floor sink, hub drain, standpipe or mop sink.

Last updated: October 2026

Why Chapter 3 matters

Chapter 3 of the 2021 International Plumbing Code (IPC) holds the general rules that apply to every system. These rules are a large share of the 10 General Knowledge questions. They are easy points if you have tabbed the chapter. The sections below follow the code's order so you can move from these notes to your book.

Connections, locations and conflicts (301–303)

301.3: Every fixture, drain and appliance that discharges liquid waste must connect directly to the sanitary drainage system, except for the indirect wastes required by Chapter 8.

301.4: Every fixture that uses water must connect, directly or indirectly, to the water supply.

301.5: Pipe sizes in the code are nominal sizes unless the code says otherwise.

301.6: Plumbing may not be placed in an elevator shaft or elevator equipment room . Floor drains, sumps and sump pumps at the base of the shaft are allowed if they are indirectly connected and meet 1003.4.

301.7: When the code and the manufacturer's instructions conflict, the more restrictive rule applies.

302.1: Ashes, rags, flammable or explosive liquids, grease and other materials that can block the system or upset treatment may not be put into the drainage system.

303.1, 303.3 and 303.4: Every pipe, fitting and device must carry the manufacturer's identification. Plastic pipe must be certified to NSF 14 , and products must be third-party listed to their standards.

Rodentproofing (304)

Strainer plates on drain inlets may have openings no larger than 1/2 inch in least dimension (304.2). Meter boxes must stop rodents from following the service pipe into the building. Annular spaces around pipes through walls, floors and ceilings must be sealed with caulk or gasketing (304.4).

Protecting pipes (305)

Section Rule

305.1 Metallic pipe, except cast iron, ductile iron and galvanized steel, may not touch steel framing, concrete, cinder or masonry, or corrosive soil. Plastic sheathing used to prevent contact must be at least 0.008 inch (8 mil) thick and must let the pipe move.

305.2 Pipe must be installed to prevent stresses from expansion, contraction and building settlement.

305.3 A pipe through a foundation wall needs a relieving arch or a sleeve two pipe sizes larger than the pipe.

305.4 Water, soil and waste pipes may not be installed where they can freeze unless protected by insulation, heat or both.

305.5 Roof and vent penetrations must be flashed watertight.

305.6 Use No. 16 gage (0.0575 inch) steel shield plates where concealed pipe is less than 1-1/4 inches from the edge of a stud, joist or rafter. The plates must extend 2 inches above sole plates and below top plates.

305.7 Components in alleys, driveways and parking garages must be recessed or protected from damage.

Sleeve sizing example. "Two pipe sizes greater" counts nominal sizes. For a 4-inch building drain, the sizes above 4 inches are 5 and 6, so the sleeve is 6 inches . For a 3-inch line, it is 3 → 3-1/2 → 4, so 4 inches. (If your supplier skips 3-1/2-inch pipe, ask the inspector how they count.)

Shield plate example. A 1-1/2-inch PVC drain (outside diameter about 1.9 inches) bored through the center of a 3-1/2-inch-deep 2×4 non-bearing stud (a hole just over 2 inches, inside the 60% limit) leaves about ( 3.5 − 1.9 ) / 2 = 0.8 (3.5-1.9)/2 = 0.8 ( 3.5 − 1.9 ) /2 = 0.8 inch on each side. That is less than 1-1/4 inches, so plates are required on both faces. Cast iron and galvanized steel are exempt from 305.6 because nails will not go through them.

Freezing (305.4) in Alabama. The model IPC tells the local jurisdiction to fill in the frost-depth and sewer-depth numbers (shown as [NUMBER] in 305.4.1). Alabama's Board adopts the 2021 IPC without filling in those values, so burial depths come from the local building department. Exposed pipes in unheated crawl spaces and exterior walls still need insulation or heat.

Trenching, excavation and backfill (306)

Buried pipe must be supported for its entire length (306.1).

306.2: Where the trench bottom is the bed, give solid and continuous support between joints. Dig bell holes at hubs and couplings, and never block pipe up to grade.

306.2.1: If you over-excavate, backfill to grade with sand or fine gravel in layers no more than 6 inches deep, compacting each layer.

306.2.2: Remove rock to at least 3 inches below the bottom of the pipe and backfill with tamped sand. The pipe and joints may not rest on rock anywhere.

306.2.3: In soft soil, over-excavate at least two pipe diameters and backfill with fine gravel, crushed stone or a concrete foundation bedded on sand.

306.3: Backfill must be free of debris. Place loose earth free of rocks, broken concrete and frozen chunks in 6-inch layers , tamping each one, until the crown is covered by 12 inches . Bring backfill up evenly on both sides so the pipe stays aligned.

306.4: Tunneled or jacked pipe must be protected from damage and later uneven loading.

307.5: A trench running parallel to a footing may not extend into the footing's bearing plane . That plane is a line sloping down at 45 degrees from the outside bottom edge of the footing.

Structural safety (307)

Section 307.2 says framing members may not be cut, notched or bored beyond the limits in the International Building Code (IBC) . Plumbing exams test those IBC limits for conventional wood framing:

Member Bored hole Notch Other limits

Bearing or exterior wall stud 40% of stud depth (60% in doubled studs, no more than two doubled studs in a row) 25% of depth Hole at least 5/8 inch from the edge; no hole and notch in the same section

Non-bearing stud 60% of depth 40% of depth 5/8 inch edge distance

Solid joist 1/3 of joist depth, at least 2 inches from top and bottom 1/6 of depth, not in the middle third of the span End notches up to 1/4 of depth

Worked numbers. In a 2×10 joist (9-1/4 inches deep), a notch in an outer third may be up to 9.25 / 6 ≈ 1.54 9.25/6 \approx 1.54 9.25/6 ≈ 1.54 inches deep. A bored hole may be up to 9.25 / 3 ≈ 3.08 9.25/3 \approx 3.08 9.25/3 ≈ 3.08 inches across, kept at least 2 inches from each edge.

307.4: Truss members may not be cut, drilled, notched, spliced or altered without written approval from a registered design professional. Adding loads such as a water heater needs verification that the truss can carry them.

Engineered lumber, such as I-joists and LVL beams, follows the manufacturer's published hole charts.

307.3 and 315.1: Penetrations of fire-resistance-rated assemblies must be protected under the IBC. The annular space around any pipe through a sleeve or building-envelope opening must be sealed with caulk, foam sealant or gasketing that suits the location.

Flood areas, toilet rooms and condensate (309–314)

309.2: In flood hazard areas, water service, drainage, vents and water heaters must be located per IBC Section 1612, or designed to keep floodwater out and resist buoyancy.

310: Toilet rooms must be lit and ventilated per the IBC and the International Mechanical Code (IMC).

314.2.1: Condensate from cooling coils must slope at least 1/8 inch per foot to an approved place of disposal.

314.2.1.1: Condensate drains may not connect directly to a drain, waste or vent pipe. They may discharge only into a floor sink, floor drain, trench drain, mop sink, hub drain, standpipe, utility sink or laundry sink. The discharge must stay within the same tenant space or dwelling unit unless it goes to grade outdoors.

314.2.2: Condensate lines must be at least 3/4 inch and may not get smaller toward the outlet.

314.2.3: Where overflow could damage the building, one of four protection methods is required: an auxiliary pan with its own drain, an overflow line from the equipment pan, an auxiliary pan with a UL 508 shutoff switch, or a UL 508 water-level shutoff device.

Exam traps

Shield plates: the threshold is less than 1-1/4 inches , and the plate is 0.0575 inch (16 gage) .

Sleeves: two pipe sizes larger, at 305.3 . Section 305.4 is about freezing.

Rock: remove it 3 inches below the pipe and use tamped sand. Soft soil needs two pipe diameters of over-excavation.

Trusses: never alter them without a design professional's written approval ( 307.4 ).

Loading diagram... IPC Chapter 3 protection and support rules