Study guide

3.2 Disinfection Byproducts (DBPs), Stage 1/2 Rules & CT Compliance

Alabama Water/Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Alabama Regulations, Certification, Exams & Utility Administration

1.1 ADEM Division 335-10-1: Facility Classifications, Grades & Staffing Rules 1.2 Becoming Certified in Alabama: Exam Application, Operator Intern Status, Experience, Renewal & CEHs 1.3 Environmental Compliance, SDWA, Clean Water Act & NPDES Permits 1.4 Alabama's PSI-Delivered WPI Exams: Format, Grade Crosswalk & Need-to-Know Blueprints 1.5 ADEM Drinking-Water Operating Rules (Division 335-7): Control Tests, Residuals, Pressure, Cross-Connections & Records 1.6 Utility Administration: SOPs, Records, Security, Cybersecurity, Emergency Planning & Supervision

2 Chapter 2: Source Water, Wells, Coagulation, Filtration & Membranes

2.1 Source Water Hydrology, Groundwater vs. Surface Water & Protection 2.2 Coagulation Chemistry, Coagulants & Rapid Mixing Mechanics 2.3 Flocculation Basin Design, Clarification & Sedimentation 2.4 Granular Media Filtration, Head Loss & Backwash Protocols 2.5 Membrane Filtration: MF, UF, NF & RO Operation, Integrity Testing and Cleaning 2.6 Wells & Groundwater Systems: Construction, Pumps, Testing and Sanitary Protection (ADEM 335-7-5)

3 Chapter 3: Water Disinfection, Chemical Addition, Stabilization & Residuals

3.1 Chlorination Chemistry, Breakpoint Chlorination & Residuals 3.2 Disinfection Byproducts (DBPs), Stage 1/2 Rules & CT Compliance 3.3 Corrosion Control, Lead and Copper Rule & Fluoridation 3.4 Iron/Manganese Removal, Water Softening & Taste/Odor Control 3.5 Water Treatment Residuals: Sludge, Backwash Recycle & Plant Discharges

4 Chapter 4: Wastewater Preliminary & Primary Treatment

4.1 Wastewater Characteristics, Screening, Shredding & Grit Removal 4.2 Primary Sedimentation Basins, Scum Removal & Clarifier Performance

5 Chapter 5: Secondary Biological Treatment: Activated Sludge

5.1 Activated Sludge Microbiology, Basin Configurations & Aeration Systems 5.2 Process Control: F/M Ratio, MCRT/SRT & Sludge Settling Characteristics 5.3 Operational Troubleshooting (Bulking, Foaming, Pin Floc) & Process Modifications

6 Chapter 6: Fixed-Film Treatment, Lagoons, Nutrient Removal, Tertiary Filtration & Disinfection

6.1 Trickling Filters & Rotating Biological Contactors (RBCs) 6.2 Waste Stabilization Ponds, Aerated Lagoons & Alabama Grade I Lagoon Operations 6.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal 6.4 Tertiary Filtration & Membrane Bioreactors (MBRs) 6.5 Wastewater Disinfection & Dechlorination: Chlorine, UV and Ozone

7 Chapter 7: Sludge Treatment, Biosolids & Odor Control

7.1 Sludge Thickening, Aerobic Digestion & Anaerobic Digestion 7.2 Mechanical Dewatering, Polymer Conditioning & EPA 503 Biosolids Regulations 7.3 Odor Control & Wastewater Chemical Addition

8 Chapter 8: Water Distribution Systems, Installation, Metering & Water Loss

8.1 Distribution Piping Materials, Valves & Finished Water Storage Facilities 8.2 Water Main Flushing, Disinfection Protocols (AWWA C651) & Water Quality Maintenance 8.3 Distribution Hydraulics, Pressure Control & Cross-Connection Prevention 8.4 Main & Service Installation, Tapping, Repair and Utility Locating (Alabama 811) 8.5 Meters, Water Loss Control, Asset Management & Customer Service

9 Chapter 9: Wastewater Collection Systems, Lift Stations & Sewer Maintenance

9.1 Gravity Collection Networks, Manhole Construction & Self-Cleansing Velocity Standards 9.2 Wastewater Lift Stations, Submersible Pumps, Force Mains & Inflow/Infiltration (I&I) 9.3 Sewer Cleaning, CCTV Inspection & SSO Response

10 Chapter 10: Laboratory Procedures, Sampling & Environmental Compliance

10.1 Drinking Water Laboratory Analysis: Turbidity, pH, Alkalinity & Coliform Testing 10.2 Wastewater Laboratory Testing: BOD5, COD, Total Suspended Solids & Settleability 10.3 Representative Sampling Protocols, Preservation, Chain of Custody & QA/QC

11 Chapter 11: Plant Equipment, Pumps, Motors & Instrumentation

11.1 Centrifugal and Positive Displacement Pumps: Operation, Cavitation & Packing/Seals 11.2 Electric Motors, Variable Frequency Drives, Flow Meters & SCADA Systems

12 Chapter 12: Safety: Chemicals, Confined Spaces & Field Hazards

12.1 Chemical Safety: Chlorine Gas Emergency Handling (Kits A & B) & Hydrogen Sulfide (H2S) Hazards 12.2 Permit-Required Confined Space Entry, Lockout/Tagout (LOTO) & Personal Protective Equipment 12.3 Field Safety: Work-Zone Traffic Control, Electrical Hazards, Fall Protection & Hazard Communication

13 Chapter 13: Water & Wastewater Mathematics: Hydraulics, Chemical Feed & Pumping

13.1 Flow Conversions, Geometry, Tank Volume & Detention Time Calculations 13.2 The Pounds Formula, Chemical Feed Rates & Solution Concentration Calculations 13.3 Pumping Math: Total Dynamic Head, Horsepower, Efficiency & Power Cost

14 Chapter 14: Water & Wastewater Mathematics: Treatment Process Calculations

14.1 Clarifier Surface Overflow Rate, Weir Loading & Granular Filter Loading Rates 14.2 Biological Calculations: F/M Ratio, MCRT Solids Balance & Sludge Volume Index (SVI)

3.2 Disinfection Byproducts (DBPs), Stage 1/2 Rules & CT Compliance

Key Takeaways Explain This Topic AI

The Surface Water Treatment Rule (SWTR) establishes mandatory microbial inactivation and removal benchmarks: 3-log (99.9%) for Giardia lamblia cysts and 4-log (99.99%) for enteric viruses.

Disinfection compliance is verified using the C T CT CT concept ( C × T 10 C \times T_{10} C × T 10 ​ ), where C C C represents disinfectant residual in mg/L and T 10 T_{10} T 10 ​ represents effective contact time (detention time achieved by 90% of water molecules).

Hydraulic baffling factors ( B F BF BF ) range from 0.1 for unbaffled circular basins prone to severe short-circuiting to 0.7 for superior serpentine cross-baffled basins and 1.0 for true plug-flow pipelines.

Reaction between free chlorine and Natural Organic Matter (NOM) generates regulated Disinfection Byproducts: Total Trihalomethanes (TTHM, MCL = 0.080 mg/L or 80 ppb) and Five Haloacetic Acids (HAA5, MCL = 0.060 mg/L or 60 ppb).

The Stage 2 D/DBP Rule enforces compliance using the Locational Running Annual Average (LRAA) at each specific monitoring location rather than a system-wide average, driving enhanced coagulation and alternative disinfectant adoption.

Last updated: October 2026

3.2 Disinfection Byproducts (DBPs), Stage 1/2 Rules & CT Compliance

Water treatment facilities must continually balance two competing regulatory imperatives: providing adequate disinfection to prevent acute waterborne disease outbreaks while minimizing chemical disinfection byproducts that pose chronic carcinogenic and reproductive health risks. This critical balance is governed by the Surface Water Treatment Rule (SWTR) and the Disinfectants and Disinfection Byproducts Rules (Stage 1 and Stage 2 D/DBPR).

1. The Surface Water Treatment Rule (SWTR) & Log Inactivation

The federal Surface Water Treatment Rule mandates that all public water systems utilizing surface water sources (or groundwater under the direct influence of surface water, GWUDI) must achieve specified minimum pathogen removal and inactivation standards:

3-Log (99.9%) Removal / Inactivation of Giardia lamblia cysts.

4-Log (99.99%) Removal / Inactivation of enteric viruses.

Physical Removal of Cryptosporidium oocysts: the Interim and Long Term 1 Enhanced SWTRs require at least 2-log removal by filtration, and the Long Term 2 rule (LT2ESWTR) adds treatment based on source-water monitoring bins.

Log Reduction Mathematics

Pathogen reduction is expressed logarithmically on a base-10 scale:

Log Reduction = log ⁡ 10 ( N in N out ) \text{Log Reduction} = \log_{10}\left(\frac{N_{\text{in}}}{N_{\text{out}}}\right) Log Reduction = lo g 10 ​ ( N out ​ N in ​ ​ )

  • Log Inactivation % Reduction Remaining Fraction
  • 1.0-log 90.0% 1 / 10 1/10 1/10 ( 10 − 1 10^{-1} 1 0 − 1 )
  • 2.0-log 99.0% 1 / 100 1/100 1/100 ( 10 − 2 10^{-2} 1 0 − 2 )
  • 3.0-log 99.9% 1 / 1 , 000 1/1,000 1/1 , 000 ( 10 − 3 10^{-3} 1 0 − 3 )
  • 4.0-log 99.99% 1 / 10 , 000 1/10,000 1/10 , 000 ( 10 − 4 10^{-4} 1 0 − 4 )
  • Treatment Train Credits: Physical Removal vs. Chemical Disinfection

Water treatment plants rarely rely on chemical disinfection alone to fulfill the entire log-reduction mandate. Instead, the multi-barrier approach credits physical clarification and filtration processes toward total compliance:

Conventional Filtration Credit: A properly operated conventional filtration facility (coagulation, flocculation, sedimentation, and granular media filtration) that consistently maintains settled water clarity and achieves combined filter effluent turbidity ≤ 0.3 NTU \le 0.3\text{ NTU} ≤ 0.3 NTU in at least 95% of monthly measurements is automatically granted:

  • 2.5-log credit for Giardia lamblia
  • 2.0-log credit for enteric viruses

2-log Cryptosporidium removal under the IESWTR (credited as 3-log for conventional treatment under the LT2ESWTR)

Disinfection Obligation: To achieve total SWTR compliance, the downstream chemical disinfection process (e.g., clearwell chlorination) must supply the remaining inactivation balance: 0.5-log for Giardia ( 3.0 − 2.5 = 0.5 3.0 - 2.5 = 0.5 3.0 − 2.5 = 0.5 ) and 2.0-log for viruses ( 4.0 − 2.0 = 2.0 4.0 - 2.0 = 2.0 4.0 − 2.0 = 2.0 ). Because Giardia cysts are far hardier and more chlorine-resistant than enteric viruses, satisfying the 0.5-log Giardia inactivation standard under free chlorine almost universally guarantees virus inactivation compliance.

2. The CT Concept and Hydraulic Baffling Factors

Chemical disinfection efficacy is quantified using the C T CT CT concept :

C T = C × T 10 CT = C \times T_{10} CT = C × T 10 ​

C C C (Disinfectant Concentration): The free chlorine residual measured at the outlet of the disinfection contact basin, expressed in milligrams per liter (mg/L).

T 10 T_{10} T 10 ​ (Effective Contact Time): The time, in minutes, required for 10% of the water volume to pass through the contact basin under peak flow conditions. In other words, 90% of the water molecules remain inside the basin for at least T 10 T_{10} T 10 ​ minutes.

Determining Theoretical Detention Time vs. Effective Contact Time

Theoretical detention time ( T T T ) represents the hydraulic average time water spends in a vessel assuming ideal, complete mixing:

T = Basin Volume (gal) Peak Flow Rate (gpm) = Basin Volume (gal) Peak Flow Rate (MGD) × 1440 min/day T = \frac{\text{Basin Volume (gal)}}{\text{Peak Flow Rate (gpm)}} = \frac{\text{Basin Volume (gal)}}{\text{Peak Flow Rate (MGD)}} \times 1440\text{ min/day} T = Peak Flow Rate (gpm) Basin Volume (gal) ​ = Peak Flow Rate (MGD) Basin Volume (gal) ​ × 1440 min/day

In real treatment basins, water does not travel as a uniform mass. Fluid friction, thermal density stratification, poorly designed inlets/outlets, and eddy currents cause hydraulic short-circuiting , where some water rushes through the tank much faster than theoretical detention time. To correct for short-circuiting, environmental regulators assign a Baffling Factor ( B F BF BF ) to basins:

T 10 = T × B F T_{10} = T \times BF T 10 ​ = T × BF

Baffling Classification Baffling Factor ( B F BF BF ) Physical Configuration Characteristics

Unbaffled / None 0.1 Circular or rectangular tank with adjacent inlet and outlet; no internal baffles; severe short-circuiting

  • Poor 0.3 Single baffle or inlet/outlet at opposite ends without internal guide walls
  • Average 0.5 Multiple inlet/outlet ports; intra-basin baffle walls directing flow

Superior 0.7 Serpentine contact chamber; multi-pass cross-baffling; perforated diffuser inlet and outlet baffles

Perfect Plug Flow 1.0 Pipeline contactors with length-to-diameter ratio > 100 : 1 > 100:1 > 100 : 1 ; zero short-circuiting

Environmental Impacts on Required CT

The required C T CT CT value is not constant; it is derived from EPA empirical lookup tables based on three operational water parameters:

Water Temperature: Cold water drastically impedes microbial inactivation kinetics. Lowering the water temperature from 20°C to 0.5°C nearly quadruples the required free chlorine C T CT CT for Giardia inactivation (at pH 7.0 and a residual of 0.4 mg/L or less, the 3-log CT rises from 52 to 195 mg·min/L). Winter operations demand significantly higher chlorine residuals or increased contact times.

Finished Water pH: Because hypochlorous acid ( HOCl \text{HOCl} HOCl ) dissociates into the weaker hypochlorite ion ( OCl − \text{OCl}^- OCl − ) as pH climbs, the required free chlorine C T CT CT increases dramatically at higher pH levels. For example, at 10°C and a residual of 0.4 mg/L or less, EPA's table requires a 3-log Giardia C T CT CT of 104 mg ⋅ min/L 104\text{ mg}\cdot\text{min/L} 104 mg ⋅ min/L at pH 7.0 but 177 mg ⋅ min/L 177\text{ mg}\cdot\text{min/L} 177 mg ⋅ min/L at pH 8.5.

Disinfectant Residual ( C C C ): At higher chlorine concentrations, the required C T CT CT increases slightly due to non-linear chemical oxidation behavior.

Calculating the CT Inactivation Ratio

Utilities track daily compliance by computing the Inactivation Ratio :

Inactivation Ratio = C T achieved C T required = C × T 10 C T required \text{Inactivation Ratio} = \frac{CT_{\text{achieved}}}{CT_{\text{required}}} = \frac{C \times T_{10}}{CT_{\text{required}}} Inactivation Ratio = C T required ​ C T achieved ​ ​ = C T required ​ C × T 10 ​ ​

To demonstrate compliance, the Inactivation Ratio must equal or exceed 1.00 at all times. If a facility operates multiple basins in series (e.g., flocculator, clarifier, filter, and clearwell), the total plant inactivation ratio is the sum of the individual ratios across all units:

Total Ratio = ∑ ( C T achieved C T required ) ≥ 1.00 \text{Total Ratio} = \sum \left( \frac{CT_{\text{achieved}}}{CT_{\text{required}}} \right) \ge 1.00 Total Ratio = ∑ ( C T required ​ C T achieved ​ ​ ) ≥ 1.00

3. Disinfection Byproducts (DBPs) Formation Chemistry

When free chlorine is added to raw surface water, it reacts with naturally occurring organic precursors to synthesize halogenated organic compounds known as Disinfection Byproducts (DBPs) . The primary organic precursors are Natural Organic Matter (NOM) —predominantly humic and fulvic acids derived from decaying vegetation and soil runoff. Precursor abundance is quantified via Total Organic Carbon (TOC) and Specific Ultraviolet Absorbance (SUVA at 254 nm).

Total Trihalomethanes (TTHMs)

Trihalomethanes are single-carbon methane derivatives where three hydrogen atoms are replaced by halogen atoms (chlorine or bromine). If raw water contains natural bromide ( Br − \text{Br}^- Br − ), chlorine oxidizes bromide to hypobromous acid ( HOBr \text{HOBr} HOBr ), which reacts rapidly with NOM to yield brominated DBPs.

NOM + HOCl + HOBr ⟶ Trihalomethanes (TTHMs) \text{NOM} + \text{HOCl} + \text{HOBr} \longrightarrow \text{Trihalomethanes (TTHMs)} NOM + HOCl + HOBr ⟶ Trihalomethanes (TTHMs)

The four regulated trihalomethanes comprising Total Trihalomethanes (TTHM) are:

  • Chloroform ( CHCl 3 \text{CHCl}_3 CHCl 3 ​ )
  • Bromodichloromethane ( CHBrCl 2 \text{CHBrCl}_2 CHBrCl 2 ​ )
  • Dibromochloromethane ( CHBr 2 Cl \text{CHBr}_2\text{Cl} CHBr 2 ​ Cl )
  • Bromoform ( CHBr 3 \text{CHBr}_3 CHBr 3 ​ )

Maximum Contaminant Level (MCL): 0.080 mg/L (80 parts per billion, μ g/L \mu\text{g/L} μ g/L ).

Health Risks: Bladder and colorectal cancers, liver and kidney toxicity, and central nervous system effects.

Formation Kinetics: TTHM formation increases with higher water temperature, higher pH (alkaline conditions accelerate the base-catalyzed haloform reaction), longer water age, and higher free chlorine residual.

Five Haloacetic Acids (HAA5)

Haloacetic acids are carboxylic acids where halogen atoms replace hydrogen atoms on the acetic acid methyl group. The five regulated haloacetic acids comprising HAA5 are:

  • Monochloroacetic acid (MCAA, CH 2 ClCOOH \text{CH}_2\text{ClCOOH} CH 2 ​ ClCOOH )
  • Dichloroacetic acid (DCAA, CHCl 2 COOH \text{CHCl}_2\text{COOH} CHCl 2 ​ COOH )
  • Trichloroacetic acid (TCAA, CCl 3 COOH \text{CCl}_3\text{COOH} CCl 3 ​ COOH )
  • Monobromoacetic acid (MBAA, CH 2 BrCOOH \text{CH}_2\text{BrCOOH} CH 2 ​ BrCOOH )
  • Dibromoacetic acid (DBAA, CHBr 2 COOH \text{CHBr}_2\text{COOH} CHBr 2 ​ COOH )

Maximum Contaminant Level (MCL): 0.060 mg/L (60 parts per billion, μ g/L \mu\text{g/L} μ g/L ).

Health Risks: Probable human carcinogenicity, mutagenic effects, and adverse reproductive/developmental outcomes.

Formation Kinetics: Unlike TTHMs, HAA5 formation is favored at neutral to slightly acidic pH. Furthermore, HAA5 compounds are subject to biological degradation in distribution networks where water age is excessive and chlorine residuals have dissipated.

4. Stage 1 and Stage 2 Disinfectants and Disinfection Byproducts Rules

The EPA promulgated the Stage 1 and Stage 2 D/DBP Rules to progressively tighten regulatory oversight:

Feature Stage 1 D/DBP Rule (1998) Stage 2 D/DBP Rule (2006)

Compliance Metric Running Annual Average (RAA) averaged across the entire distribution network Locational Running Annual Average (LRAA) evaluated independently at each monitoring site

TTHM Standard 0.080 mg/L 0.080\text{ mg/L} 0.080 mg/L ( 80 μ g/L 80\ \mu\text{g/L} 80 μ g/L ) 0.080 mg/L 0.080\text{ mg/L} 0.080 mg/L ( 80 μ g/L 80\ \mu\text{g/L} 80 μ g/L ) at every site

HAA5 Standard 0.060 mg/L 0.060\text{ mg/L} 0.060 mg/L ( 60 μ g/L 60\ \mu\text{g/L} 60 μ g/L ) 0.060 mg/L 0.060\text{ mg/L} 0.060 mg/L ( 60 μ g/L 60\ \mu\text{g/L} 60 μ g/L ) at every site

Disinfectant Limits MRDL: Chlorine/Chloramines = 4.0 mg/L; ClO 2 \text{ClO}_2 ClO 2 ​ = 0.8 mg/L MRDL remains unchanged

Site Selection Representative points (average and extreme dead ends) Identified via Initial Distribution System Evaluation (IDSE) targeting highest DBP formation

  • Early Warning None Operational Evaluation Levels (OELs) trigger mandatory plant evaluation
  • The Critical Shift: RAA vs. LRAA

Under Stage 1, a utility could mask an extreme TTHM spike at a distant storage tank (e.g., 0.110 mg/L 0.110\text{ mg/L} 0.110 mg/L ) by averaging it with low values from samples taken near the treatment plant (e.g., 0.040 mg/L 0.040\text{ mg/L} 0.040 mg/L ), yielding an acceptable system-wide average of 0.075 mg/L 0.075\text{ mg/L} 0.075 mg/L .

Under Stage 2, every single monitoring site must maintain an LRAA below the MCL. The LRAA is computed at the end of each quarter by averaging the most recent four consecutive quarters of data collected at that specific location. A single chronic hot spot results in a direct regulatory violation for the entire water system.

Operational Evaluation Levels (OELs)

Stage 2 mandates that systems calculate an Operational Evaluation Level at each monitoring site every quarter:

OEL = Q 1 + Q 2 + 2 ( Q 3 ) 4 \text{OEL} = \frac{Q_1 + Q_2 + 2(Q_3)}{4} OEL = 4 Q 1 ​ + Q 2 ​ + 2 ( Q 3 ​ ) ​

Where Q 1 Q_1 Q 1 ​ is the concentration from two quarters ago, Q 2 Q_2 Q 2 ​ is the concentration from the prior quarter, and Q 3 Q_3 Q 3 ​ is the current quarter's concentration. By weighting the current quarter by a factor of 2, the OEL projects whether the site will breach the MCL in the subsequent quarter. An OEL exceedance does not constitute a violation, but it legally obligates the utility to submit an engineering evaluation to the state regulatory agency within 90 days examining source water quality, coagulant dosing, clearwell contact times, and storage tank turnover.

Enhanced Coagulation Requirements

Stage 1 established Enhanced Coagulation as a treatment technique for conventional surface water plants. Systems must remove a specified percentage of raw water Total Organic Carbon (TOC) prior to chemical disinfection, based on raw water alkalinity:

  • Raw Water TOC (mg/L) Raw Alkalinity 0–60 mg/L Raw Alkalinity 60–120 mg/L Raw Alkalinity > 120 mg/L
  • > 2.0 to 4.0 35.0% TOC Removal 25.0% TOC Removal 15.0% TOC Removal
  • > 4.0 to 8.0 45.0% TOC Removal 35.0% TOC Removal 25.0% TOC Removal
  • > 8.0 50.0% TOC Removal 40.0% TOC Removal 30.0% TOC Removal

Systems with raw water SUVA ≤ 2.0 L/mg ⋅ m \text{SUVA} \le 2.0\text{ L/mg}\cdot\text{m} SUVA ≤ 2.0 L/mg ⋅ m or treated water TOC < 2.0 mg/L \text{TOC} < 2.0\text{ mg/L} TOC < 2.0 mg/L are exempt from enhanced coagulation requirements.

5. DBP Control Strategies & Alternative Disinfectants

To achieve Stage 2 compliance without compromising microbial barriers, utilities employ targeted chemical and operational modifications:

Precursor Removal (Enhanced Coagulation): Increasing alum or ferric chloride coagulant dosing past the minimum turbidity-removal point depresses pH (to 5.5–6.3) and neutralizes negatively charged organic molecules, precipitating NOM before chlorine is applied.

Moving the Chlorination Point: Historically, plants dosed chlorine at the rapid mix basin ("pre-chlorination"). By moving primary chlorination to settled water or post-filtration, chlorine contacts water only after 50% to 70% of organic precursors have been physically extracted.

Alternative Disinfectants:

Disinfectant Microbial Strengths Microbial Weaknesses Regulated DBPs Formed Residual Stability

Free Chlorine ( Cl 2 \text{Cl}_2 Cl 2 ​ ) Outstanding virus and bacterial kill; good Giardia kill Ineffective against Cryptosporidium at normal doses TTHMs, HAA5 Moderate decay; reacts with biofilm

Chloramines ( NH 2 Cl \text{NH}_2\text{Cl} NH 2 ​ Cl ) Excellent biofilm penetration; stable secondary residual Very weak primary disinfectant; poor Giardia inactivation Low TTHM/HAA5; forms NDMA and cyanogen chloride Highly persistent in large distribution grids

Chlorine Dioxide ( ClO 2 \text{ClO}_2 ClO 2 ​ ) Powerful primary disinfectant; effective on Giardia & Cryptosporidium Sensitive to sunlight; volatile gas must be generated on-site Chlorite (MCL = 1.0 mg/L), Chlorate Does not maintain persistent distribution residual

Ozone ( O 3 \text{O}_3 O 3 ​ ) Strongest chemical disinfectant; rapid Cryptosporidium inactivation Extremely costly; leaves zero residual; off-gassing safety hazard Bromate (MCL = 0.010 mg/L in bromide-rich waters) Zero residual (decays within minutes)

Ultraviolet (UV) Light Exceptional physical inactivation of Cryptosporidium & Giardia Ineffective against adenoviruses without extreme dose Zero regulated halogenated DBPs Zero chemical residual (requires secondary disinfectant)

6. Operational Worked Calculations: CT & Inactivation Ratio

A surface water treatment plant operates a clearwell contact basin at a peak winter flow of 4.5 MGD. The clearwell has an effective storage volume of 400,000 gallons. Tracer studies have demonstrated that the cross-baffled basin has a hydraulic baffling factor of 0.60. At peak flow, the free chlorine residual exiting the basin is 1.6 mg/L, the water temperature is 10°C, and the finished pH is 7.5.

EPA's free chlorine CT table (Table B-1 in EPA's Disinfection Profiling and Benchmarking guidance) gives a 3-log Giardia CT ( C T 99.9 CT_{99.9} C T 99.9 ​ ) of 144 mg·min/L at 10°C, pH 7.5 and 1.6 mg/L. Because the plant receives 2.5-log Giardia credit for conventional filtration, disinfection must supply 0.5 log .

Step 1: Calculate theoretical hydraulic detention time ( T T T ). T = Volume Peak Flow = 400 , 000 gal 4 , 500 , 000 gal/day × 1440 min/day = 128.0 minutes T = \frac{\text{Volume}}{\text{Peak Flow}} = \frac{400,000\text{ gal}}{4,500,000\text{ gal/day}} \times 1440\text{ min/day} = 128.0\text{ minutes} T = Peak Flow Volume ​ = 4 , 500 , 000 gal/day 400 , 000 gal ​ × 1440 min/day = 128.0 minutes

Step 2: Calculate effective contact time ( T 10 T_{10} T 10 ​ ). T 10 = T × B F = 128.0 min × 0.60 = 76.8 minutes T_{10} = T \times BF = 128.0\text{ min} \times 0.60 = 76.8\text{ minutes} T 10 ​ = T × BF = 128.0 min × 0.60 = 76.8 minutes

Step 3: Calculate achieved C T CT CT ( C T achieved CT_{\text{achieved}} C T achieved ​ ). C T achieved = C × T 10 = 1.6 mg/L × 76.8 min = 122.88 mg ⋅ min/L CT_{\text{achieved}} = C \times T_{10} = 1.6\text{ mg/L} \times 76.8\text{ min} = 122.88\text{ mg}\cdot\text{min/L} C T achieved ​ = C × T 10 ​ = 1.6 mg/L × 76.8 min = 122.88 mg ⋅ min/L

Step 4: Convert to log inactivation and evaluate compliance. Log inactivation = 3 × C T achieved C T 99.9 = 3 × 122.88 144 = 2.56 log \text{Log inactivation} = 3 \times \frac{CT_{\text{achieved}}}{CT_{99.9}} = 3 \times \frac{122.88}{144} = 2.56\text{ log} Log inactivation = 3 × C T 99.9 ​ C T achieved ​ ​ = 3 × 144 122.88 ​ = 2.56 log

The clearwell provides about 2.56 log of Giardia inactivation, far more than the 0.5 log required, so it complies with the Surface Water Treatment Rule. Expressed as an inactivation ratio for the 0.5-log requirement, the required CT is 144 ÷ 6 = 24 mg ⋅ min/L 144 \div 6 = 24\text{ mg}\cdot\text{min/L} 144 ÷ 6 = 24 mg ⋅ min/L and the ratio is 122.88 ÷ 24 = 5.1 122.88 \div 24 = 5.1 122.88 ÷ 24 = 5.1 , comfortably above 1.00.

Loading diagram... Disinfection Kinetics and Disinfection Byproduct Regulations