Study guide

6.1 Application Defects and Failure Modes

AMPP CIP Level 1 Basic Coatings Inspector

Track your progress as you read

Finished sections get a check mark.

1 Introduction and Exam Overview

AMPP CIP Level 1 Exam Overview and Certification Path

2 Chapter 2: Surface Preparation Standards

SSPC-SP Solvent and Tool Cleaning Standards Abrasive Blast Cleaning Grades Power Tool to Bare Metal, Specialty, and Water Jetting Standards

3 Surface Profile and Contaminants

Surface Profile Measurement per ASTM D4417 Visual Standards and Rust Grades Contaminant Testing and Abrasive Selection

4 Chapter 4: Coating Materials and Types

4.1 Coating Chemistry and Curing Mechanisms 4.2 Zinc-Rich Primers and Corrosion Protection 4.3 Coating Properties and Calculations 4.4 Specialty Coatings and Service Environments

5 Chapter 5 — Application Methods

5.1 Spray Application Techniques 5.2 Stripe Coating and Critical Areas

6 Chapter 6: Inspection and Defects

6.1 Application Defects and Failure Modes 6.2 Adhesion and Cure Testing 6.3 Inspector Role, Documentation, and Project Coordination

7 Ambient Conditions

Psychrometry and Instruments Dew Point Rule and Application Limits Environmental Control and Documentation

8 Chapter 8: Film Thickness Measurement

8.1 Wet Film Thickness 8.2 Dry Film Thickness Gauges and Calibration 8.3 DFT Acceptance Criteria and Procedures

9 Chapter 9: Holiday Detection

9.1 Holiday Detection Methods 9.2 Holiday Repair and Verification

10 Safety, Ethics, and Inspector Standards

OSHA Safety Standards AMPP Code of Ethics and Inspector Professional Conduct

6.1 Application Defects and Failure Modes

Key Takeaways Explain This Topic AI

Orange peel, runs, and sags stem from spray gun setup errors: low atomization pressure or high viscosity for orange peel, excessive WFT or gun-too-close for runs and sags.

Pinholes form when trapped air or solvent escapes after the wet film has skinned; zinc-rich primers are especially prone because heavy pigment packs and releases air.

Mud cracking is caused by applying a single coat beyond the PDS maximum WFT on fast-curing or high-build coatings; it cannot be repaired in place and requires removal and recoating.

Fish-eye cratering is caused by silicone or oil surface contamination; SSPC-SP 1 solvent cleaning and a water break test are the prevention steps.

Holidays (discontinuities) are detected per ASTM D5162: low-voltage wet sponge at 9-90 V DC for coatings 20 mils or less, high-voltage spark testing for coatings over 20 mils.

Last updated: July 2026

Quick Answer: Each coating application defect traces to a specific root cause. Orange peel comes from inadequate atomization or high viscosity. Runs and sags come from excessive wet film thickness. Pinholes come from trapped solvent or air escaping after the surface skins. Mud cracking comes from over-thickness in fast-curing coatings. Fish-eyes come from silicone or oil contamination. Blistering comes from soluble salts or cathodic disbondment. Dry spray comes from the gun held too far or hot dry air. Holidays come from thin or skipped application. The CIP inspector identifies each defect, documents the location, and requires correction per the specification.

Orange Peel, Runs, Sags, and Pinholes

Orange peel appears as a textured, dimpled surface resembling citrus peel. The cause is inadequate atomization — air pressure too low in conventional spray, fluid pressure too low in airless spray, or material viscosity too high from cold conditions or insufficient thinning. Prevention: adjust spray pressure, warm or thin the material per the product data sheet (PDS), and maintain the correct gun distance (typically 12 to 18 inches). Orange peel reduces effective film thickness and traps contaminants, so it must be sanded smooth before recoating.

Runs and sags are gravity-driven downward flow of excess wet coating. The cause is too much material deposited in one pass — gun too slow, gun too close, overlap too high, or material over-thinned. Prevention: maintain a steady gun speed and approximately 50 percent overlap, keep the gun perpendicular to the surface, and verify WFT with a comb gauge (ASTM D4414) after application. Runs should be brushed out before the coating skins; once cured, they require sanding and reapplication.

Pinholes are tiny voids extending through the coating to the substrate. The cause is trapped air or solvent escaping from the wet film after the surface has skinned, or air entrainment from aggressive agitation. Zinc-rich primers are prone because heavy zinc pigment packs and releases trapped air. Prevention: apply the mist coat technique (a light pass followed by a full pass), reduce gun distance, ensure proper induction time for two-component materials, and avoid over-agitation. Pinholes are critical in immersion service because they expose bare metal.