Study guide
6.2 Adhesion and Cure Testing
AMPP CIP Level 1 Basic Coatings Inspector
Track your progress as you read
Finished sections get a check mark.
1 Introduction and Exam Overview
AMPP CIP Level 1 Exam Overview and Certification Path
2 Chapter 2: Surface Preparation Standards
SSPC-SP Solvent and Tool Cleaning Standards Abrasive Blast Cleaning Grades Power Tool to Bare Metal, Specialty, and Water Jetting Standards
3 Surface Profile and Contaminants
Surface Profile Measurement per ASTM D4417 Visual Standards and Rust Grades Contaminant Testing and Abrasive Selection
4 Chapter 4: Coating Materials and Types
4.1 Coating Chemistry and Curing Mechanisms 4.2 Zinc-Rich Primers and Corrosion Protection 4.3 Coating Properties and Calculations 4.4 Specialty Coatings and Service Environments
5 Chapter 5 — Application Methods
5.1 Spray Application Techniques 5.2 Stripe Coating and Critical Areas
6 Chapter 6: Inspection and Defects
6.1 Application Defects and Failure Modes 6.2 Adhesion and Cure Testing 6.3 Inspector Role, Documentation, and Project Coordination
7 Ambient Conditions
Psychrometry and Instruments Dew Point Rule and Application Limits Environmental Control and Documentation
8 Chapter 8: Film Thickness Measurement
8.1 Wet Film Thickness 8.2 Dry Film Thickness Gauges and Calibration 8.3 DFT Acceptance Criteria and Procedures
9 Chapter 9: Holiday Detection
9.1 Holiday Detection Methods 9.2 Holiday Repair and Verification
10 Safety, Ethics, and Inspector Standards
OSHA Safety Standards AMPP Code of Ethics and Inspector Professional Conduct
6.2 Adhesion and Cure Testing
Key Takeaways Explain This Topic AI
ASTM D4541 pull-off adhesion uses a hydraulic tester and glued dolly to measure the maximum pressure at failure, with the failure mode (substrate, cohesive, or adhesive) documented.
ASTM D3359 Method A (X-cut, two cuts crossing at 30-45°) is used for coatings over 5 mils; Method B (crosshatch, 6 or 11 blades in a lattice) is used for coatings 5 mils or less.
ASTM D5402 solvent rub verifies cure of thermoset coatings (epoxies, urethanes) by rubbing with a solvent-soaked cloth and checking for softening, wrinkling, or transfer.
Cure stages the inspector distinguishes are set-to-touch, dry-hard, dry-through, and full cure per the PDS.
Intercoat adhesion depends on respecting the recoat window — too early causes solvent entrapment, too late requires roughening or a tie coat.
Last updated: July 2026
Quick Answer: Adhesion and cure testing on AMPP projects uses three primary ASTM standards. ASTM D4541 pull-off adhesion measures the force required to pull a glued dolly off the coated substrate using a hydraulic tester. ASTM D3359 cross-cut and tape adhesion scores the coating with a blade and applies tape to assess removal — Method A (X-cut) for coatings over 5 mils, Method B (crosshatch) for coatings 5 mils or less. ASTM D5402 solvent rub verifies cure by rubbing with a solvent-soaked cloth and inspecting for softening or transfer. Intercoat adhesion is confirmed by cross-cut testing between coats at the recoat window.
ASTM D4541 Pull-Off Adhesion
ASTM D4541 covers the pull-off adhesion test using a pneumatic or hydraulic adhesion tester. A metal dolly (commonly 20 mm diameter) is glued to the cured coating with an epoxy adhesive, the tester pulls perpendicular to the surface, and the maximum pressure at failure (psi or MPa) is recorded. The inspector must document the failure mode, because the value is only meaningful when the failure mode is understood:
Substrate failure : the coating pulls off the steel, exposing the substrate. This is the only failure mode that gives a true coating adhesion value.
Cohesive failure : the break occurs within a coating layer, which is useful for evaluating intercoat strength in multi-coat systems.
Adhesive failure : the break is at the dolly-glue or glue-coating interface, which means the test measured glue strength, not coating adhesion, and the result is invalid for adhesion acceptance.
The inspector verifies the test area is flat, the dolly is perpendicular to the surface, and the gauge is calibrated per the manufacturer's instructions before each test series. D4541 is quantitative and is the standard for structural adhesion acceptance on AMPP projects. The minimum acceptable pull-off value is set by the project specification, commonly 1,500 psi or greater for industrial maintenance coatings. The inspector records the dolly diameter, pull rate, failure pressure, and failure mode in the daily inspection report, and photographs the failure surface for the project record.