Study guide
6.3 Inspector Role, Documentation, and Project Coordination
AMPP CIP Level 1 Basic Coatings Inspector
Track your progress as you read
Finished sections get a check mark.
1 Introduction and Exam Overview
AMPP CIP Level 1 Exam Overview and Certification Path
2 Chapter 2: Surface Preparation Standards
SSPC-SP Solvent and Tool Cleaning Standards Abrasive Blast Cleaning Grades Power Tool to Bare Metal, Specialty, and Water Jetting Standards
3 Surface Profile and Contaminants
Surface Profile Measurement per ASTM D4417 Visual Standards and Rust Grades Contaminant Testing and Abrasive Selection
4 Chapter 4: Coating Materials and Types
4.1 Coating Chemistry and Curing Mechanisms 4.2 Zinc-Rich Primers and Corrosion Protection 4.3 Coating Properties and Calculations 4.4 Specialty Coatings and Service Environments
5 Chapter 5 — Application Methods
5.1 Spray Application Techniques 5.2 Stripe Coating and Critical Areas
6 Chapter 6: Inspection and Defects
6.1 Application Defects and Failure Modes 6.2 Adhesion and Cure Testing 6.3 Inspector Role, Documentation, and Project Coordination
7 Ambient Conditions
Psychrometry and Instruments Dew Point Rule and Application Limits Environmental Control and Documentation
8 Chapter 8: Film Thickness Measurement
8.1 Wet Film Thickness 8.2 Dry Film Thickness Gauges and Calibration 8.3 DFT Acceptance Criteria and Procedures
9 Chapter 9: Holiday Detection
9.1 Holiday Detection Methods 9.2 Holiday Repair and Verification
10 Safety, Ethics, and Inspector Standards
OSHA Safety Standards AMPP Code of Ethics and Inspector Professional Conduct
6.3 Inspector Role, Documentation, and Project Coordination
Key Takeaways Explain This Topic AI
The CIP inspector's authority is defined by the contract and inspection plan: hold points stop work until verification, witness points notify the inspector, and stop-work authority halts application when conditions or quality fall outside the specification.
The pre-job conference finalizes the inspection plan, hold and witness points, ambient limits, acceptance criteria, and documentation requirements before any coating work begins.
The daily inspection report (DIR) is the inspector's primary record and must capture date, weather, ambient readings, surface prep verification, batch numbers, WFT, DFT, defects, and signatures every shift.
A non-conformance report (NCR) documents any deviation from the specification — DFT below the 80/120 minimum, wrong SP grade, pinholes after cure, or recoating outside the recoat window — with disposition and corrective action.
The inspector verifies, documents, and reports but never directs the contractor's work; records are retained per the project specification, typically a minimum of three years.
Last updated: July 2026
Quick Answer: The AMPP CIP inspector's authority is defined by the project specification and the inspection plan agreed at the pre-job conference. The inspector operates at hold points (work cannot proceed without inspector verification), witness points (the inspector is notified and may observe), and exercises stop-work authority to halt application when conditions or quality fall outside the specification. All observations are documented in the daily inspection report (DIR), non-conformances are escalated through an NCR, and the assembled records form the quality verification trail for the project.
Inspector Authority and Inspection Points
The CIP Level 1 inspector's authority comes from the contract and specification, not from personal opinion. Three levels of inspection point are defined in the inspection plan:
Hold point (H) : work must stop and cannot proceed until the inspector verifies compliance and signs off. Common hold points include the surface preparation grade before priming, the stripe coat before the full coat, and WFT immediately after application.
Witness point (W) : the contractor must notify the inspector so the inspector may observe, but work may proceed if the inspector is absent after proper notification. Witness points are less restrictive than hold points and are used for non-critical verification steps.
Stop-work authority : the inspector may halt all coating work when ambient conditions, surface preparation, or application quality violate the specification and the contractor refuses corrective action.
The inspector never directs the contractor's work — that is the contractor's responsibility. The inspector verifies, documents, and reports. Stop-work is invoked through the owner or the owner's representative per the project escalation chain defined in the inspection plan, not unilaterally by the inspector walking off the job. The inspector's role is to provide objective evidence of compliance or non-compliance, not to manage or supervise the contractor's crew.