Study guide
9.1 Holiday Detection Methods
AMPP CIP Level 1 Basic Coatings Inspector
Track your progress as you read
Finished sections get a check mark.
1 Introduction and Exam Overview
AMPP CIP Level 1 Exam Overview and Certification Path
2 Chapter 2: Surface Preparation Standards
SSPC-SP Solvent and Tool Cleaning Standards Abrasive Blast Cleaning Grades Power Tool to Bare Metal, Specialty, and Water Jetting Standards
3 Surface Profile and Contaminants
Surface Profile Measurement per ASTM D4417 Visual Standards and Rust Grades Contaminant Testing and Abrasive Selection
4 Chapter 4: Coating Materials and Types
4.1 Coating Chemistry and Curing Mechanisms 4.2 Zinc-Rich Primers and Corrosion Protection 4.3 Coating Properties and Calculations 4.4 Specialty Coatings and Service Environments
5 Chapter 5 — Application Methods
5.1 Spray Application Techniques 5.2 Stripe Coating and Critical Areas
6 Chapter 6: Inspection and Defects
6.1 Application Defects and Failure Modes 6.2 Adhesion and Cure Testing 6.3 Inspector Role, Documentation, and Project Coordination
7 Ambient Conditions
Psychrometry and Instruments Dew Point Rule and Application Limits Environmental Control and Documentation
8 Chapter 8: Film Thickness Measurement
8.1 Wet Film Thickness 8.2 Dry Film Thickness Gauges and Calibration 8.3 DFT Acceptance Criteria and Procedures
9 Chapter 9: Holiday Detection
9.1 Holiday Detection Methods 9.2 Holiday Repair and Verification
10 Safety, Ethics, and Inspector Standards
OSHA Safety Standards AMPP Code of Ethics and Inspector Professional Conduct
9.1 Holiday Detection Methods
Key Takeaways Explain This Topic AI
The 20-mil (500 µm) DFT threshold divides low-voltage wet sponge testing (≤20 mils, 9–90 V DC) from high-voltage spark testing (>20 mils, calculated voltage).
ASTM D5162 defines Method A (low-voltage wet sponge) and Method B (high-voltage spark tester) for nonconductive coatings on metallic substrates.
NACE/AMPP SP0188 provides the voltage calculation formula for high-voltage testing: the classic formula is V = 1250 × √t (t in mils).
Never add sodium chloride to the wet sponge solution — it produces false indications and contaminates the surface, harming intercoat adhesion.
The detector ground lead must bond directly to bare metal; a poor ground connection is the most common cause of missed holidays.
Last updated: July 2026
Quick Answer: Holiday detection tests the integrity of a protective coating by applying an electrical voltage across it. If current finds a path through a discontinuity — a holiday, pinhole, or void — to the conductive substrate, the detector signals a fault. ASTM D5162 governs the practice for nonconductive coatings on metal. NACE/AMPP SP0188 provides the voltage calculation formulas. The 20-mil (500 µm) DFT threshold is the critical dividing line: coatings at or below 20 mils use low-voltage wet sponge testing at 9–90 V DC; coatings above 20 mils use high-voltage spark testing with voltage calculated from coating thickness.
Governing Standards: ASTM D5162 and NACE/AMPP SP0188
ASTM D5162, Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates , defines two methods: Method A (low-voltage wet sponge) and Method B (high-voltage spark tester). The standard establishes the 20-mil boundary, specifies calibration verification, and requires the coating be sufficiently cured before testing to avoid false readings and fire hazards from retained solvent.
NACE/AMPP SP0188 supplements D5162 with voltage calculation formulas and procedural detail. The 2024 revision introduced a Paschen's Law-based formula producing higher voltages, but the classic formula V = 1250 × √t (t in mils) remains widely used in field practice and CIP Level 1 study materials.
- Parameter Low-Voltage Wet Sponge High-Voltage Spark
- Coating DFT range ≤ 20 mils (500 µm) > 20 mils (500 µm)
- Voltage source 9–90 V DC (fixed by instrument) Calculated from DFT
- Electrode Moist sponge Brush, spring, or flat ribbon
- Signal Audible/visual alarm Audible/visual spark
- Substrate requirement Bare metal ground connection Direct bond to bare metal
- Low-Voltage Wet Sponge Testing (≤ 20 Mils)
Low-voltage testing applies to thin-film coating systems with total DFT at or below 20 mils. The instrument supplies a fixed DC voltage between 9 and 90 volts — the exact value is set by the manufacturer's circuit design, not by coating thickness. A sponge saturated with tap water serves as the moving electrode. A low-sudsing wetting agent may be added at approximately 30 mL per 4 L. The inspector passes the sponge over the surface at roughly 0.3 m/s (1 ft/s) using a double pass. When the sponge contacts bare metal at a holiday, the circuit completes and the alarm sounds.
Critical rule: Never add sodium chloride (salt) to the sponge solution. Salt produces erroneous indications and contaminates the surface, compromising intercoat adhesion. Only tap water and an approved wetting agent are permitted.
Sensitivity verification differs by instrument type. For relay-type testers, an 80,000-ohm resistor should actuate the alarm and a 100,000-ohm resistor should not. For oscillator-type testers, resistance values of 10 MΩ, 1 MΩ, 100 kΩ, and 10 kΩ are checked for discernible frequency increase. Low-voltage testers shall not be used on coatings exceeding 20 mils — the method lacks sensitivity at greater thicknesses.