Study guide

AMPP Code of Ethics and Inspector Professional Conduct

AMPP CIP Level 1 Basic Coatings Inspector

Track your progress as you read

Finished sections get a check mark.

1 Introduction and Exam Overview

AMPP CIP Level 1 Exam Overview and Certification Path

2 Chapter 2: Surface Preparation Standards

SSPC-SP Solvent and Tool Cleaning Standards Abrasive Blast Cleaning Grades Power Tool to Bare Metal, Specialty, and Water Jetting Standards

3 Surface Profile and Contaminants

Surface Profile Measurement per ASTM D4417 Visual Standards and Rust Grades Contaminant Testing and Abrasive Selection

4 Chapter 4: Coating Materials and Types

4.1 Coating Chemistry and Curing Mechanisms 4.2 Zinc-Rich Primers and Corrosion Protection 4.3 Coating Properties and Calculations 4.4 Specialty Coatings and Service Environments

5 Chapter 5 — Application Methods

5.1 Spray Application Techniques 5.2 Stripe Coating and Critical Areas

6 Chapter 6: Inspection and Defects

6.1 Application Defects and Failure Modes 6.2 Adhesion and Cure Testing 6.3 Inspector Role, Documentation, and Project Coordination

7 Ambient Conditions

Psychrometry and Instruments Dew Point Rule and Application Limits Environmental Control and Documentation

8 Chapter 8: Film Thickness Measurement

8.1 Wet Film Thickness 8.2 Dry Film Thickness Gauges and Calibration 8.3 DFT Acceptance Criteria and Procedures

9 Chapter 9: Holiday Detection

9.1 Holiday Detection Methods 9.2 Holiday Repair and Verification

10 Safety, Ethics, and Inspector Standards

OSHA Safety Standards AMPP Code of Ethics and Inspector Professional Conduct

AMPP Code of Ethics and Inspector Professional Conduct

Key Takeaways Explain This Topic AI

The AMPP Code of Ethics requires impartiality, honesty, integrity, and non-modification of the project specification; the full text is provided during CIP course registration.

Inspectors must disclose any financial, personal, or contractual conflict of interest and decline work where the conflict cannot be managed.

At hold points the inspector verifies conformance before work proceeds; when the specification is violated, the inspector has authority to stop the non-conforming work and issue an NCR.

A Daily Inspection Report (DIR) records weather, instruments, readings, and results each shift; a Non-Conformance Report (NCR) is issued for every specification deviation.

The CIP Level 1 inspector reviews the full project specification before work begins and works under supervision of a senior inspector on complex projects.

Last updated: July 2026

Quick Answer: The AMPP Code of Ethics requires certified coating inspectors to act with impartiality, honesty, and integrity; avoid conflicts of interest; not modify or override the project specification; and document work accurately through daily inspection reports (DIR) and non-conformance reports (NCR). The inspector's authority includes holding or stopping work at defined hold and witness points when specifications are violated. The full Code of Ethics text is provided during CIP course registration and is not published publicly without AMPP membership.

AMPP Code of Ethics — Publicly Documented Principles

The AMPP Code of Ethics is delivered in full to candidates at CIP course registration. The publicly documented general principles include:

Impartiality : perform inspection work without bias toward the owner, the contractor, or the coating manufacturer.

Honesty : reporting must be truthful, accurate, and free of falsification or alteration of data.

Integrity : uphold the specification as written and do not act outside the defined inspector role.

Conflict of interest : disclose any financial, personal, or contractual interest that could influence judgment and decline work where the conflict cannot be managed.

Non-modification of specifications : do not change, relax, or interpret away specification requirements; only the specifier or owner can authorize a deviation, typically through a formal change order.

Confidentiality : protect the owner's and employer's proprietary information, including product formulations, pricing, and project schedules.

A CIP inspector paid by a coating manufacturer to recommend that manufacturer's product on a project where they are also the independent inspector is in a conflict of interest.

Conflict of Interest and Professional Conduct

Recognizing conflicts is a recurring exam theme. Common conflict-of-interest situations and their handling:

Situation Ethical issue Handling

Inspector holds stock in coating manufacturer on project Financial conflict Disclose and decline if influence cannot be managed

Inspector's spouse works for the contractor Personal conflict Disclose to owner and contractor; recuse if needed

  • Inspector accepts gifts from contractor Appearance of bias Decline gifts that could influence decisions
  • Inspector rounds a failing DFT up to pass Falsification Report actual readings; issue NCR

Inspector changes a spec without owner approval Spec modification (prohibited) Refer deviation to specifier for written disposition

Inspector works for owner and contractor on adjacent projects Dual-interest Disclose to both parties; manage separation

Professional conduct also extends to job-site behavior: following all site safety rules, not interfering with contractor operations beyond the inspector role, reporting observations factually without editorializing or assigning blame.