Study guide

Surface Contaminants and Acid Cleaning

AMPP CIP Level 2 Certified Coatings Inspector

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

CIP Level 2 Exam Facts and Format Prerequisites, Certification Path, and Renewal July 2026 Blueprint and Study Strategy

2 Safety

Process Safety: Equipment and Job-Site Hazards Safety Issues for Specialized Coatings and Prep Methods Environmental Safety Regulations and Regulatory Layers Containment, Waste, VOC, Silica, and Hexavalent Chromium

3 Inspection Planning

Evaluating and Applying Client Written Expectations Purpose and Cost Justification of Inspection Creating Inspection and Test Plans (ITPs) Supporting Job Specifications

4 Inspection Activities & Standards

De Facto, National, and International Standards CIP Level 2 Scope vs Level 1 Responsibilities Verifying Level 1 Work and Applying NACE/AMPP Standards

5 Corrosion Causes

Corrosion Types: General, Localized, Crevice, Flow-Assisted Corrosion Cell and Electrochemical Processes Galvanic Corrosion and Dissimilar Metals

6 Corrosion Effect & Control

Substrate Corrosion Rates, Influencing Factors, and Mitigation Cathodic Protection Systems and Effects on Coatings

7 Environmental Conditions & Inspection

Environmental Requirements and Inspection Concerns Humidity Effects on Corrosion Rates and Coating Risk Dehumidification Systems: Desiccant, Refrigerant, and Heaters Enclosures, Air Movement, and Advanced Environmental Instrumentation

8 Surface Preparation Methods

Prep Methods for Nonferrous, Wood, Concrete, and Polymeric Substrates Surface Contaminants and Acid Cleaning Pickling, Passivation, and Rinse Verification Waterjetting Methods and Removable Materials

9 Surface Prep Equipment & Standards

Concrete Surface Preparation and Standards Abrasive Types, Mixes, and Inspection Considerations Centrifugal Blast Cleaning and Portable/Remote Systems Waterjetting and Centrifugal Blast Standards AB-1/2/3 Media Standards and Special Substrates

10 Coating Application Equipment

Thermal, Electrostatic, and Polyester Spray Applications Plural-Component Systems and Specialty Coating Application Convertible vs Non-Convertible Curing and Polymerization

11 Specialty Coatings & Products

Powder Coatings and Specialized Coating Types Thick-Barrier Linings: Installation and Use Coal-Tar Enamel, Asphalt, and Tape Coatings Maintenance Coating Considerations

12 Pipeline Coatings & Hot-Dip Galvanizing

Hot-Dip Galvanizing Application Process Fusion-Bonded Epoxy (FBE) Pipeline Coating Multi-Layer Polyolefin (3LPE/3LPP) Pipeline Coatings Pipeline Field Joints and Mainline Repair Products Pipeline Coating Importance and Integrity Failure Consequences Concrete on Pipelines and Concrete Coating Standards Concrete Coating Requirements and Cure Verification

13 Coating Inspection: Assessing

Coating Surveys of Existing Systems Coating Defects, Failures, and Detection Criteria Differentiating Adhesion Testing Methods HDG Defects; Nonferrous and Concrete Coating Inspection

14 Coating Inspection: Verification

Instrument Inspections: Verification vs Calibration Concrete Coating Thickness and Destructive Tests Eddy Current and Ultrasonic DFT Methods Cathodic Disbondment and Specialized Lab Testing

15 Documentation

Level 1 Report Review and Failure Documentation for Level 3 Documenting Specialty Coatings and Developing Reports Electronic Reporting, Data Storage, and Retention Maintenance Coating Surveys and Standards Bodies Product Data Sheets and Hot-Dip Galvanizing Standards

16 Communications & Teamwork

Certified Inspector Role and CIP Level 2 Limits Owner, Contractor, and Inspector Responsibilities Pre-Job Conference and Coating Condition Assessment Surveyor Defensive Behavior and Conflict Resolution Communication

17 Ethics

Attestation and Ethics of the AMPP-Certified Inspector Addressing and Analyzing Ethical Dilemmas Positive Suggestions That Improve Job Flow and Quality

Surface Contaminants and Acid Cleaning

Key Takeaways Explain This Topic AI

Contaminants divide into visible soils, invisible soluble salts, oils and greases, and process residues — each needing a different removal method.

Sequence matters: soluble oils and greases are removed before abrasive work, or blasting simply drives them into the profile.

Soluble salts are invisible, survive abrasive blasting, and are detected by extraction test methods rather than by eye.

Acid cleaning removes oxides and light scale chemically and introduces its own residue, rinse, and neutralisation concerns.

A visually clean surface is not necessarily a contamination-free surface; the specification decides which invisible contaminants must also be tested.

Last updated: August 2026

Contaminants, Acid Residuals, Pickling, and Passivation

Quick Answer: Domain 5 requires CIP Level 2 inspectors to understand removal of surface contaminants and acid residuals and the importance of passivation , including chemical prep by acid cleaning, pickling, and passivation —with inspection focus on neutralization, rinse water quality, and residual acidity testing.

Mechanical blast gets the most field attention, but many failures start with invisible soils or chemical residues . Oils under a “perfect” blast profile, chloride salts under primer, or unneutralized pickle acid under stainless passivation each produce adhesion loss, blistering, or accelerated corrosion. Level 2 work treats chemical cleanliness as a hold-point discipline , not a shop afterthought.

Surface Contaminants: What Must Be Removed

Contaminants are materials on the substrate that interfere with coating adhesion, promote corrosion under the film, or react with the coating chemistry. Categories inspectors should recognize:

Contaminant class Examples Why it matters

Organic soils Oils, greases, cutting fluids, fingerprints, form-release agents Prevent wetting and adhesion; create fisheyes

Soluble salts Chlorides, sulfates, nitrates from marine air, process chemicals, sweat Osmotic blistering, underfilm corrosion

  • Particulates Dust, blast dust, grinding swarf, insulation fibers Nibs, holidays, weak interfaces
  • Corrosion products / scale Rust, mill scale, heat tint, weld scale Barrier to adhesion; active corrosion cells

Old coatings / residues Chalk, poorly adherent paint, adhesive tapes, markers Delamination between coats or to substrate

Chemical residuals Acids, alkalis, cleaners, strippers not fully rinsed Attack coating or metal; delayed burns for handlers

Sequence principle

Heavy greases and oils should be cleaned before aggressive abrasive work when possible—blasting oily steel smears contamination and loads media. Soluble salts may require water washing, wet abrasive, waterjetting, or chemical treatment in addition to dry blast. The specification and PDS define acceptance (for example, maximum chloride micrograms per square centimeter when salt testing is required).

  • Inspection of contaminant removal
  • Visual: no visible oil sheen, smut, dust, or loose scale in the area to be coated
  • Water-break / wipe tests where specified for organic films
  • Soluble salt tests (conductivity, chloride-specific kits) when the ITP requires them

UV or solvent wipe checks for residual oils on critical stainless or hygienic surfaces when project procedures call for them

Document where and when tests were done relative to coating application—recontamination from hands, weather, and adjacent work is common.

Acid Cleaning (Chemical Cleaning)

Acid cleaning uses acid solutions (or inhibited acid cleaners) to dissolve light oxides, mineral deposits, or specific soils that detergents alone cannot remove. It is broader than full pickling of heavy mill scale. Field and shop variants include:

  • Phosphoric or other acid cleaners for light rust and oxide on steel (when specified)
  • Acid descalers for process equipment
  • Specialty acid gels for local treatment of welds or heat tint
  • Inspection concerns for acid cleaning

Correct chemistry and concentration per the approved procedure—wrong acid on the wrong alloy destroys the part (classic example: chloride-bearing acids on stainless or aluminum when not intended).

Contact time and temperature within procedure limits; over-etching thins metal or opens grain boundaries on sensitive alloys.

Complete rinsing with water of acceptable quality (rinse quality and residual-acidity verification are covered in the next section).

Neutralization when the procedure requires it—leaving residual acidity is a coating and safety defect.

Dryness and recontamination control before coating or the next chemical step.

Acid cleaning is both a quality and a safety interface: splash burns, fume exposure, and incompatible chemical mixing are contractor controls; residual acid on the work piece is also an inspection defect.

Why Sequence Is the Whole Battle

The recurring field failure in contaminant removal is not choosing the wrong method — it is choosing the right methods in the wrong order.

Wrong sequence What actually happens

Blast first, then degrease Abrasive drives oil into the profile and contaminates the media; the surface looks clean and fails anyway

Blast first, then salt test Salts remain in the profile valleys; the reading may pass while contamination sits under the peaks

Wash with water before removing heavy grease Grease is spread rather than removed and the surface stays hydrophobic

Coat immediately after acid cleaning without rinse verification Residual acid attacks the coating from beneath and can burn workers handling the part

The general rule: remove what dissolves in solvent first, then what dissolves in water, then what requires mechanical energy — adjusted by the specification's own stated sequence, which always governs.

Distinguishing "clean" from "prepared"

Two words that candidates blur, and the exam separates:

Clean describes what has been removed : soils, oils, salts, oxides, loose material.

Prepared describes what has been created : the specified cleanliness grade and, on steel, the specified anchor profile.

A chemically cleaned surface can be extremely clean and still be unprepared, because no profile has been produced. A blasted surface can carry a textbook profile and still be contaminated, because soluble salts survived the blast. Both conditions pass one test and fail the other, and both are common. Level 2 practice is to verify each attribute against its own criterion rather than letting one stand in for the other.

What the inspector records

For contaminant removal to be defensible, the record needs more than "surface cleaned." Capture the method used, the area, the time, the test performed if any, the result with its units, and the instrument or kit identity. "Bresle extraction, Bay 3 north face, 14:20, 8 µg/cm² chloride against a project maximum of 10" is evidence. "Salt test OK" is a note to yourself.