Waterjetting Methods and Removable Materials

AMPP CIP Level 2 Certified Coatings Inspector

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

CIP Level 2 Exam Facts and Format Prerequisites, Certification Path, and Renewal July 2026 Blueprint and Study Strategy

2 Safety

Process Safety: Equipment and Job-Site Hazards Safety Issues for Specialized Coatings and Prep Methods Environmental Safety Regulations and Regulatory Layers Containment, Waste, VOC, Silica, and Hexavalent Chromium

3 Inspection Planning

Evaluating and Applying Client Written Expectations Purpose and Cost Justification of Inspection Creating Inspection and Test Plans (ITPs) Supporting Job Specifications

4 Inspection Activities & Standards

De Facto, National, and International Standards CIP Level 2 Scope vs Level 1 Responsibilities Verifying Level 1 Work and Applying NACE/AMPP Standards

5 Corrosion Causes

Corrosion Types: General, Localized, Crevice, Flow-Assisted Corrosion Cell and Electrochemical Processes Galvanic Corrosion and Dissimilar Metals

6 Corrosion Effect & Control

Substrate Corrosion Rates, Influencing Factors, and Mitigation Cathodic Protection Systems and Effects on Coatings

7 Environmental Conditions & Inspection

Environmental Requirements and Inspection Concerns Humidity Effects on Corrosion Rates and Coating Risk Dehumidification Systems: Desiccant, Refrigerant, and Heaters Enclosures, Air Movement, and Advanced Environmental Instrumentation

8 Surface Preparation Methods

Prep Methods for Nonferrous, Wood, Concrete, and Polymeric Substrates Surface Contaminants and Acid Cleaning Pickling, Passivation, and Rinse Verification Waterjetting Methods and Removable Materials

9 Surface Prep Equipment & Standards

Concrete Surface Preparation and Standards Abrasive Types, Mixes, and Inspection Considerations Centrifugal Blast Cleaning and Portable/Remote Systems Waterjetting and Centrifugal Blast Standards AB-1/2/3 Media Standards and Special Substrates

10 Coating Application Equipment

Thermal, Electrostatic, and Polyester Spray Applications Plural-Component Systems and Specialty Coating Application Convertible vs Non-Convertible Curing and Polymerization

11 Specialty Coatings & Products

Powder Coatings and Specialized Coating Types Thick-Barrier Linings: Installation and Use Coal-Tar Enamel, Asphalt, and Tape Coatings Maintenance Coating Considerations

12 Pipeline Coatings & Hot-Dip Galvanizing

Hot-Dip Galvanizing Application Process Fusion-Bonded Epoxy (FBE) Pipeline Coating Multi-Layer Polyolefin (3LPE/3LPP) Pipeline Coatings Pipeline Field Joints and Mainline Repair Products Pipeline Coating Importance and Integrity Failure Consequences Concrete on Pipelines and Concrete Coating Standards Concrete Coating Requirements and Cure Verification

13 Coating Inspection: Assessing

Coating Surveys of Existing Systems Coating Defects, Failures, and Detection Criteria Differentiating Adhesion Testing Methods HDG Defects; Nonferrous and Concrete Coating Inspection

14 Coating Inspection: Verification

Instrument Inspections: Verification vs Calibration Concrete Coating Thickness and Destructive Tests Eddy Current and Ultrasonic DFT Methods Cathodic Disbondment and Specialized Lab Testing

15 Documentation

Level 1 Report Review and Failure Documentation for Level 3 Documenting Specialty Coatings and Developing Reports Electronic Reporting, Data Storage, and Retention Maintenance Coating Surveys and Standards Bodies Product Data Sheets and Hot-Dip Galvanizing Standards

16 Communications & Teamwork

Certified Inspector Role and CIP Level 2 Limits Owner, Contractor, and Inspector Responsibilities Pre-Job Conference and Coating Condition Assessment Surveyor Defensive Behavior and Conflict Resolution Communication

17 Ethics

Attestation and Ethics of the AMPP-Certified Inspector Addressing and Analyzing Ethical Dilemmas Positive Suggestions That Improve Job Flow and Quality

Waterjetting Methods and Removable Materials

Key Takeaways Explain This Topic AI

Waterjetting is a primary surface-preparation method that uses high-velocity water to clean substrates and remove selected materials without dry abrasive media

Pressure classes range from high-pressure water cleaning through ultra-high-pressure (UHP) waterjetting; higher pressure increases coating and rust removal capability

Waterjetting removes soluble salts, loose coatings, and some rust/corrosion products effectively; it does not create a new angular abrasive-blast profile—it can expose an existing profile

Flash rust grades describe the appearance of rust that forms on wet steel after waterjetting and before coating; specifications define acceptable flash-rust condition at coating time

Detailed waterjetting standards and acceptance photos belong with standards training; this section focuses on methods, materials removed, and inspection concepts

Last updated: August 2026

Waterjetting Methods and Removable Materials

Quick Answer: CIP Level 2 treats waterjetting as surface preparation (not optional trivia): know pressure-class awareness (high-pressure vs ultra-high-pressure), what materials waterjetting removes well (soluble salts, loose coatings, some rust), that it does not create a new angular abrasive profile , and the concept of flash rust grades after wet cleaning.

Dry abrasive blast is still common, but waterjetting (also called water jetting, hydroblasting in some trades language, or UHP waterjetting at the highest pressures) is a mainstream industrial prep method for ships, tanks, offshore structures, and environmentally restricted sites. Domain 5 lists both waterjetting as prep and materials effectively removed by waterjetting as inspector knowledge. Detailed numeric standard tables and photo grades are covered with waterjetting standards in the next chapter; here the focus is method physics, pressure awareness, removable materials, and inspection concepts .

What Waterjetting Is

Waterjetting cleans or prepares a surface by directing a high-velocity water stream at the substrate. No abrasive grit is required for pure waterjetting (though wet abrasive hybrid methods exist as a separate family). Energy comes from pump pressure and nozzle design; the jet shears, erodes, and washes contaminants and coating films.

Compared with dry blast:

• Aspect Dry abrasive blast Waterjetting (pure water)
• Cleaning medium Solid grit + air Water at high velocity
• Dust High unless contained Low dust; mist and slurry instead
• Soluble salts May leave/embed salts; often needs wash Excellent salt removal when used properly
• Profile Can cut new angular profile Does not cut a new steel grit-type profile
• Media disposal Spent grit Water, paint chips, and dissolved/suspended soils
• Fire / spark Sparks possible with some setups No abrasive spark; electrical/water interface risks
• Pressure Classes Overview (Awareness Level)

Industry practice groups water cleaning and jetting by pressure class . Exact definitions and standard labels live in waterjetting standards (next chapter); Level 2 must retain the concept ladder :

Lower-pressure water cleaning

Used for washing, salt reduction, and removal of loose dirt and chalk. Limited ability to strip tightly adherent coatings or heavy rust. Often a pre-step before coating or before higher-pressure work.

High-pressure waterjetting / water cleaning

Higher energy removes more loosely to moderately adherent materials, light coatings, and more corrosion product than simple wash-down. Still may not equal UHP for heavy, tightly bonded films.

Ultra-high-pressure (UHP) waterjetting

UHP delivers the highest industrial jet energies used in coating prep. It can strip many industrial coatings and corrosion products to a standard waterjetting cleanliness condition when equipment, technique, and dwell are correct. Reaction force, injection injury risk, and production control are correspondingly higher (see specialty-methods safety).

Exam mindset: Higher pressure class generally means greater ability to remove coatings and corrosion products , not automatic creation of abrasive-blast profile. Matching pressure class to the material to be removed and the specification’s waterjetting grade is a planning and inspection issue.

What Waterjetting Removes Effectively

The blueprint emphasizes identifying the materials effectively removed by waterjetting. Strong suits:

Soluble salts

Chlorides, sulfates, and other water-soluble salts dissolve and wash away when water contact, volume, and technique are adequate. This is a major advantage over dry blast alone, which can leave or redistribute salts. Projects with strict salt limits often specify waterjetting or water washing as part of prep.

Loose and poorly adherent coatings

Blistered, chalked, peeling, and otherwise non-adherent paint films are readily removed. Tight, flexible, well-adhered multi-coat systems may require UHP, multiple passes, or supplemental methods—do not assume any water pressure strips any coating in one pass.

Loose rust and some corrosion products

Laminar rust, pack rust loosened by corrosion, and many non-adherent corrosion products are removed. Tight, hard mill scale and dense, tightly adherent oxides may resist pure waterjetting more than abrasive blast—specifications may combine methods or accept a waterjetting cleanliness condition that still shows dark tightly adherent matter depending on the standard grade selected.

Dirt, chalk, marine growth, and process soils

Mud, chalk bloom, loose process deposits, and many marine fouling layers are good waterjetting targets when environmental discharge is controlled.

Materials effectively removed — summary table

• Material / condition Waterjetting effectiveness (typical)
• Soluble salts (chlorides, etc.) High — primary strength
• Loose / peeling coatings High
• Chalk and surface dirt High
• Loose rust / non-adherent corrosion products High to moderate
• Tightly adherent coatings (varies by film and pressure class) Moderate to high with UHP; lower at low pressure
• Tight mill scale on steel Often limited vs abrasive blast
• Grease / heavy oil Poor unless pre-cleaned — oil can redeposit; degrease first
• Deeply embedded contaminants in pits Variable — may need dwell, multiple angles, or follow-up
• What Waterjetting Does NOT Do (Critical Distinction)
• Does not create a new angular abrasive profile

Angular surface profile (anchor pattern) for many coating systems is produced by cutting the steel with abrasive . Pure waterjetting does not forge a new grit-blast profile . Instead, waterjetting can:

• Expose an existing profile that was under old coating or rust
• Leave the substrate relatively smooth if the original surface was smooth
• Clean into pits without reshaping peak-to-valley geometry the way grit does

If the specification requires a new angular profile of a stated mil/micron height, waterjetting alone is usually insufficient —abrasive blast, power-tool profiling, or wet abrasive methods may be required. Inspectors who measure “profile” after pure UHP and expect grit-like peaks are applying the wrong mental model.

Does not replace degreasing of heavy oils

Water can spread oils. Degrease first when soils are oily.

Does not eliminate the need for drying and environmental control before coating

Wet surfaces must meet the coating’s moisture and environmental requirements; flash rust may form during the wet-to-coat window.

Flash Rust Grades — Concept

After waterjetting steel, the clean wet metal can form flash rust (light rust bloom) as it dries or while still damp, depending on conditions and time. Coating systems and waterjetting standards describe flash rust grades or conditions (for example, light, moderate, heavy conceptual levels) that indicate how much rust bloom is acceptable at the time of coating application .

CIP Level 2 inspection concepts:

Flash rust is expected after many wet prep methods; the question is whether the amount and type meet the specification at coating time

Heavier flash rust generally means more corrosion product on the surface that may need re-cleaning or may be allowed only to a defined grade

Inhibitors in water, dehumidification, and short wet-to-coat times manage flash rust—but inhibitors must be approved for the coating system

Document flash-rust condition with the same seriousness as cleanliness grade; coating over heavy flash rust when the spec allows only light is a defect

Detailed photo-grade tables sit with waterjetting standards training; remember the concept : flash rust grade is an acceptance condition for coating after wet prep.

• Process Elements Inspectors Should Recognize
• Equipment train

Pumps, high-pressure hose, lances/nozzles, filters, and often vacuum recovery or collection for effluent. Leaks and fitting failures are high-energy hazards.

• Technique variables that change results
• Stand-off distance and angle
• Traverse speed and overlap
• Nozzle type (rotary heads common for production)
• Water quality (chlorides in water can recontaminate)
• Number of passes
• Environmental and waste interfaces

Waterjetting reduces airborne grit dust but creates wastewater and coating debris slurry . Containment, filtration, and disposal rules still apply—especially when removing lead or chromate films.

• Hold points
• After waterjetting: cleanliness condition per specified waterjetting standard/grade
• Soluble salt verification if required
• Flash rust condition immediately before coating
• Dryness / environmental parameters per PDS
• Materials Removal vs Method Selection (Field Scenarios)

Scenario A — Salt-contaminated coastal tank exterior, existing coating mostly failed and loose. Waterjetting is often preferred because it removes salts and loose paint with lower dust. Verify flash rust and salt tests before recoat.

Scenario B — New steel with tight mill scale, specification requires 2–3 mil angular profile for a zinc primer. Pure waterjetting will clean salts if washed but will not produce the required new angular profile; abrasive blast (or specified alternative profiling) is needed.

Scenario C — Maintenance of a system where only chalk and light corrosion are present. Lower- or high-pressure water cleaning plus localized UHP may be enough if the remaining coating is sound and the spec allows feathering and spot prep.

Link to Standards (Next Chapter)

Waterjetting standards define cleanliness grades, flash-rust descriptions, and how to specify pressure and acceptance. This section’s exam load is: waterjetting is prep; know pressure-class awareness , what is removed well , profile limitation , and flash rust concept . Do not invent grit-profile expectations from a water-only process.

Exam Focus

Expect items that ask which contaminants waterjetting removes best ( soluble salts , loose coatings), whether waterjetting creates new angular profile (it does not; it may expose existing profile), and what flash rust grades represent (condition of rust bloom after wet prep before coating).