Study guide
9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements
AMPP CP1 Cathodic Protection Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & CP Exam Overview
About the AMPP CP1 Tester Exam & Certification Path How to Study for CP1 & Navigate This Guide Corrosion Science & Industry Terminology Glossary Field Mathematics & Ohm's Law Fundamentals AMPP Ethics for the Corrosion Professional
2 Chapter 2: Fundamentals of Electrochemistry & Corrosion Cells
2.1 The Corrosion Cell: Anode, Cathode, Electrolyte & Metallic Path 2.2 Anodic & Cathodic Reactions on Carbon Steel 2.3 Galvanic Series & Electromotive Force (EMF) Series 2.4 Forms of Corrosion: Uniform, Galvanic, Pitting & Crevice 2.5 Factors Affecting Corrosion Rates: Oxygen, pH, Temperature & Flow
3 Chapter 3: Principles of Cathodic Protection
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams 3.2 Galvanic (Sacrificial Anode) CP Systems 3.3 Impressed Current Cathodic Protection (ICCP) Systems 3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys 3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum
4 Chapter 4: Electrical Circuit Analysis for CP
4.1 Ohm's Law Applications in CP Circuits 4.2 Series & Parallel Resistance in CP Groundbeds & Piping 4.3 Kirchhoff's Voltage & Current Laws in Network Piping 4.4 Shunts: Types, Ratings & Current Calculations 4.5 Rectifier Operation & Transformer Tap Adjustments
5 Chapter 5: Reference Electrodes & Half-Cell Potentials
5.1 Copper/Copper Sulfate (CSE) Reference Electrode Construction & Maintenance 5.2 Silver/Silver Chloride (Ag/AgCl) & Zinc Reference Electrodes 5.3 Converting Potentials Between Reference Electrodes 5.4 Reference Electrode Care, Temperature Correction & Contamination Checks 5.5 High-Impedance Voltmeters & Contact Resistance Errors
6 Chapter 6: Field Measurement & Potential Criteria
6.1 Structure-to-Electrolyte Potential Measurement Procedures 6.2 The -850 mV CSE Polarized Criterion (NACE SP0169) 6.3 The 100 mV Polarization Decay Criterion 6.4 Understanding IR Drop & The Instant-Off Interruption Technique 6.5 Native, On, Polarized, & Off Potentials Comparison
7 Chapter 7: Advanced Field Survey Techniques
Soil Resistivity Testing: Wenner 4-Pin Method (ASTM G57) Soil Pin Spacing, Layering & Corrosivity Classification Close Interval Potential Surveys (CIPS) Direct Current Voltage Gradient (DCVG) Coating Fault Surveys Cathodic Protection Coupons for IR-Free Potential Measurements
8 Chapter 8: Test Stations, Isolation & Stray Current
8.1 Test Station Types, Lead Wires & Commissioning Inspection 8.2 Electrical Isolation Joints & Dielectric Flange Testing 8.3 Casing Isolation & Shorted Casing Testing 8.4 DC Stray Current Interference: Detection & Mitigation 8.5 AC Stray Current Interference & Induction Hazards (NACE SP0177)
9 Chapter 9: Industry Standards & Field Documentation
9.1 NACE SP0169: External Corrosion Control Overview 9.2 NACE TM0497: Measurement Techniques Standard 9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements 9.4 CP Data Collection, Logging & Quality Assurance 9.5 Rectifier Maintenance & Routine Inspection Logs 9.6 Anode Groundbed Testing & Resistance Measurements
10 Chapter 10: Electrical & Operational Safety for CP Personnel
10.1 Rectifier Electrical Safety, Lockout/Tagout (LOTO) & NFPA 70E 10.2 AC Induction Hazards Near High-Voltage Power Lines 10.3 Hazardous Atmospheres & Confined Space Safety at Test Vaults 10.4 Personal Protective Equipment (PPE) & Arc Flash Protection 10.5 Excavation, Trenching & Underground Utility Location (811) 10.6 Stop-Work Authority & Emergency Response Procedures
9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements
Key Takeaways Explain This Topic AI
PHMSA enforces 49 CFR Part 192 (natural gas) and Part 195 (hazardous liquids), which mandate specific CP requirements.
Regulations require that pipelines be tested at least once each calendar year, with intervals not exceeding 15 months.
Rectifiers must be inspected six times per year, with intervals not exceeding 2.5 months.
Non-compliance with PHMSA regulations can result in severe financial penalties, operational shutdowns, and legal liabilities.
Last updated: July 2026
Regulatory Framework for Cathodic Protection
While NACE/AMPP standards provide the engineering best practices for cathodic protection, the federal government turns these practices into law. In the United States, the primary regulatory body overseeing pipeline safety is the Pipeline and Hazardous Materials Safety Administration (PHMSA), an agency within the Department of Transportation (DOT). For the CP Tester, understanding the regulatory requirements of PHMSA, as well as relevant Environmental Protection Agency (EPA) regulations for underground storage tanks (USTs), is just as critical as understanding Ohm's Law. Failure to comply with these regulations is a violation of federal law.
PHMSA 49 CFR Part 192 (Natural Gas) and Part 195 (Hazardous Liquids)
The core of federal pipeline regulation is found in Title 49 of the Code of Federal Regulations (CFR). Part 192 governs the transportation of natural and other gas by pipeline, while Part 195 governs the transportation of hazardous liquids (such as crude oil and refined products). Both parts contain specific, legally binding subparts dedicated entirely to corrosion control.
These regulations heavily reference NACE SP0169. In many ways, PHMSA has adopted the engineering criteria of SP0169 and embedded them into federal law. Therefore, when a tester evaluates a pipeline against the -850 mV criterion, they are not just performing a technical test; they are verifying legal compliance.
Mandated Inspection Intervals
One of the most frequently tested topics on the AMPP CP1 exam is the specific schedule mandated by PHMSA for CP inspections. Testers must memorize these intervals:
Annual Pipeline Surveys (Test Stations): According to both Part 192 and Part 195, each pipeline that is under cathodic protection must be tested to determine whether the CP system meets the established criteria. This test must be conducted at least once each calendar year, but with intervals not exceeding 15 months. This "15-month rule" provides operators a slight scheduling buffer but strictly prohibits going longer than a year and a quarter between reads.
Rectifier Inspections: The power sources driving impressed current systems require more frequent monitoring. PHMSA mandates that each cathodic protection rectifier or other impressed current power source must be inspected six times each calendar year, but with intervals not exceeding 2.5 months. This ensures that failures in power supply are detected and corrected rapidly, preventing the pipeline from remaining unprotected for extended periods.
Interference Bonds: Critical interference bonds (those whose failure would jeopardize structural protection) must also be inspected six times each calendar year, with intervals not exceeding 2.5 months. Non-critical bonds must be inspected annually (not exceeding 15 months).
Deficiencies and Remedial Action
PHMSA regulations explicitly dictate what must happen when a CP survey reveals that protection criteria are not being met. If an annual survey or a 60-day rectifier check indicates inadequate protection, the operator must initiate remedial action promptly. While the exact definition of "promptly" can be subject to interpretation based on the severity of the risk, a general industry standard (often audited by PHMSA) expects remediation planning to begin immediately, with repairs typically completed before the next inspection cycle.
EPA Regulations for Underground Storage Tanks (USTs)
In addition to pipelines, CP Testers frequently work on Underground Storage Tanks, primarily regulated by the EPA under 40 CFR Part 280. The EPA requires that metallic UST systems have corrosion protection to prevent the release of regulated substances (like gasoline) into the soil and groundwater.
For USTs, CP systems must be tested by a qualified cathodic protection tester within 6 months of installation and at least every 3 years thereafter. Furthermore, impressed current systems on USTs must be inspected every 60 days to ensure the equipment is operating properly. The penalties for EPA non-compliance, particularly if a leak occurs due to failed CP, are astronomical.
The Legal Importance of the CP Tester
As an AMPP CP1 Tester, your signature on a data log or inspection report is a legal attestation that the test was performed correctly and the data is accurate. If a pipeline ruptures or a tank leaks, investigators from PHMSA or the EPA will immediately audit the CP records. If those records are falsified, incomplete, or show unresolved deficiencies, the operator faces massive fines, and the individual tester could face professional and legal consequences.
Understanding the strict schedules dictated by 49 CFR Part 192/195 and 40 CFR Part 280 is foundational. The regulations exist because corrosion failures cost lives and devastate the environment; the CP Tester is the first line of defense in ensuring those regulations are actively met in the field.