Study guide
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams
AMPP CP1 Cathodic Protection Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & CP Exam Overview
About the AMPP CP1 Tester Exam & Certification Path How to Study for CP1 & Navigate This Guide Corrosion Science & Industry Terminology Glossary Field Mathematics & Ohm's Law Fundamentals AMPP Ethics for the Corrosion Professional
2 Chapter 2: Fundamentals of Electrochemistry & Corrosion Cells
2.1 The Corrosion Cell: Anode, Cathode, Electrolyte & Metallic Path 2.2 Anodic & Cathodic Reactions on Carbon Steel 2.3 Galvanic Series & Electromotive Force (EMF) Series 2.4 Forms of Corrosion: Uniform, Galvanic, Pitting & Crevice 2.5 Factors Affecting Corrosion Rates: Oxygen, pH, Temperature & Flow
3 Chapter 3: Principles of Cathodic Protection
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams 3.2 Galvanic (Sacrificial Anode) CP Systems 3.3 Impressed Current Cathodic Protection (ICCP) Systems 3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys 3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum
4 Chapter 4: Electrical Circuit Analysis for CP
4.1 Ohm's Law Applications in CP Circuits 4.2 Series & Parallel Resistance in CP Groundbeds & Piping 4.3 Kirchhoff's Voltage & Current Laws in Network Piping 4.4 Shunts: Types, Ratings & Current Calculations 4.5 Rectifier Operation & Transformer Tap Adjustments
5 Chapter 5: Reference Electrodes & Half-Cell Potentials
5.1 Copper/Copper Sulfate (CSE) Reference Electrode Construction & Maintenance 5.2 Silver/Silver Chloride (Ag/AgCl) & Zinc Reference Electrodes 5.3 Converting Potentials Between Reference Electrodes 5.4 Reference Electrode Care, Temperature Correction & Contamination Checks 5.5 High-Impedance Voltmeters & Contact Resistance Errors
6 Chapter 6: Field Measurement & Potential Criteria
6.1 Structure-to-Electrolyte Potential Measurement Procedures 6.2 The -850 mV CSE Polarized Criterion (NACE SP0169) 6.3 The 100 mV Polarization Decay Criterion 6.4 Understanding IR Drop & The Instant-Off Interruption Technique 6.5 Native, On, Polarized, & Off Potentials Comparison
7 Chapter 7: Advanced Field Survey Techniques
Soil Resistivity Testing: Wenner 4-Pin Method (ASTM G57) Soil Pin Spacing, Layering & Corrosivity Classification Close Interval Potential Surveys (CIPS) Direct Current Voltage Gradient (DCVG) Coating Fault Surveys Cathodic Protection Coupons for IR-Free Potential Measurements
8 Chapter 8: Test Stations, Isolation & Stray Current
8.1 Test Station Types, Lead Wires & Commissioning Inspection 8.2 Electrical Isolation Joints & Dielectric Flange Testing 8.3 Casing Isolation & Shorted Casing Testing 8.4 DC Stray Current Interference: Detection & Mitigation 8.5 AC Stray Current Interference & Induction Hazards (NACE SP0177)
9 Chapter 9: Industry Standards & Field Documentation
9.1 NACE SP0169: External Corrosion Control Overview 9.2 NACE TM0497: Measurement Techniques Standard 9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements 9.4 CP Data Collection, Logging & Quality Assurance 9.5 Rectifier Maintenance & Routine Inspection Logs 9.6 Anode Groundbed Testing & Resistance Measurements
10 Chapter 10: Electrical & Operational Safety for CP Personnel
10.1 Rectifier Electrical Safety, Lockout/Tagout (LOTO) & NFPA 70E 10.2 AC Induction Hazards Near High-Voltage Power Lines 10.3 Hazardous Atmospheres & Confined Space Safety at Test Vaults 10.4 Personal Protective Equipment (PPE) & Arc Flash Protection 10.5 Excavation, Trenching & Underground Utility Location (811) 10.6 Stop-Work Authority & Emergency Response Procedures
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams
Key Takeaways Explain This Topic AI
Cathodic protection works by polarizing the cathode to the open-circuit potential of the anode.
Mixed-potential theory is used to explain the electrochemical kinetics of corrosion and CP.
A corrosion cell requires four elements: anode, cathode, electrolyte, and a metallic return path.
Tafel slopes represent the relationship between overpotential and the logarithm of current density.
Polarization reduces the potential difference between anodic and cathodic sites, stopping corrosion.
Last updated: July 2026
Cathodic Protection Theory & Mixed-Potential Diagrams
Cathodic protection (CP) is arguably the most effective and widely applied method for mitigating the corrosion of metallic structures buried in soil or immersed in water. To truly understand how CP functions, one must first deeply grasp the mechanics of the basic corrosion cell, the concept of polarization, and the electrochemical kinetics that govern these reactions, often visualized using mixed-potential diagrams.
The Fundamental Corrosion Cell
Corrosion of metals in aqueous environments is an electrochemical process. For corrosion to occur, four distinct components must be present simultaneously. If any one of these components is removed, the corrosion process halts entirely. The four components are:
The Anode: This is the location on the metal surface where oxidation occurs. Metal atoms lose electrons and dissolve into the electrolyte as positively charged ions (e.g., Fe → Fe2+ + 2e-). The anode is the site of actual metal loss or corrosion.
The Cathode: This is the location on the metal surface where reduction occurs. Electrons generated at the anode travel to the cathode, where they react with species in the electrolyte (e.g., oxygen or hydrogen ions) to form harmless byproducts (e.g., O2 + 2H2O + 4e- → 4OH-). The cathode does not corrode.
The Electrolyte: This is the conductive medium (such as soil, seawater, or freshwater) that surrounds the anode and cathode. It allows for the migration of ions, which completes the electrical circuit.
The Metallic Return Path: This is the physical connection between the anode and the cathode (usually the pipeline or structure itself) that allows electrons to flow from the anodic site to the cathodic site.
Cathodic protection works by artificially making the entire structure to be protected act as a cathode. By supplying a surplus of electrons from an external source, the anodic reactions on the structure are suppressed, thereby halting corrosion.
Polarization
When a metal is immersed in an electrolyte, it assumes a specific electrochemical potential known as its "free corrosion potential" or "open-circuit potential." When current flows to or from the metal surface, its potential shifts away from this open-circuit value. This shift in potential due to the flow of current is called polarization .
There are two primary types of polarization relevant to CP:
Activation Polarization: This is controlled by the reaction sequence at the metal-electrolyte interface. It represents the energy barrier that must be overcome for the electrochemical reaction to proceed. Activation polarization is typically the dominant form of polarization in strongly agitated or highly acidic environments where reactants are readily available.
Concentration Polarization: This is controlled by the diffusion of reactants to, or products away from, the metal surface. In neutral environments, such as typical soils or seawater, the availability of dissolved oxygen at the cathode is often the rate-limiting step. As oxygen is consumed at the cathode, a concentration gradient forms, leading to concentration polarization.
In most practical CP applications on buried pipelines, both activation and concentration polarization play a role, with concentration polarization often being significant due to limited oxygen diffusion in soil.
Mixed-Potential Theory and E log I Diagrams
Mixed-potential theory provides a powerful framework for understanding how cathodic protection eliminates corrosion. It states that any electrochemical reaction can be divided into two or more partial oxidation and reduction reactions, and there can be no net accumulation of electrical charge during an electrochemical process.
This theory is graphically represented using Evans diagrams or E log I diagrams (Mixed-Potential Diagrams). These diagrams plot potential (E) on a linear scale against the logarithm of current (log I).
Understanding the E log I Diagram
In an actively corroding system, the anodic areas have a more negative open-circuit potential ( E a E_a E a ) than the cathodic areas ( E c E_c E c ). Because they are electrically connected by the metal, electrons flow from the anode to the cathode. This causes the anode to polarize in the positive direction and the cathode to polarize in the negative direction.
The point where the anodic and cathodic polarization curves intersect represents the corrosion potential ( E c o r r E_{corr} E corr ) and the corrosion current ( I c o r r I_{corr} I corr ) . At this point, the rate of oxidation exactly equals the rate of reduction.
How CP Works on the Diagram
When CP is applied, external current is forced onto the structure. This external current supplies the electrons needed for the cathodic reduction reactions. As more external current is applied, the structure becomes increasingly polarized in the negative (cathodic) direction.
According to mixed-potential theory, to completely stop corrosion, the entire structure must be polarized to a potential equal to or more negative than the open-circuit potential of the most active anodic site on the structure ( E a E_a E a ). When the structure reaches E a E_a E a , the potential difference between the anodic and cathodic sites becomes zero. With no potential difference, no corrosion current can flow between them, and corrosion is arrested. The external current required to achieve this state is the protection current.
Tafel Slopes
The straight-line portion of the activation polarization curve on an E log I diagram is described by the Tafel equation. The slope of this line is known as the Tafel slope .
Anodic Tafel Slope ( β a \beta_a β a ): Describes how the anodic potential changes with current.
Cathodic Tafel Slope ( β c \beta_c β c ): Describes how the cathodic potential changes with current.
Understanding Tafel slopes is critical for advanced CP design, as they help predict how much current is needed to achieve a specific potential shift.
Worked Example: Calculating Voltage Shift
Imagine a steel pipeline with a natural corrosion potential of -0.550 V CSE. To achieve a standard CP criterion, we might want to polarize it to -0.850 V CSE. The required voltage shift is the difference between the polarized potential and the native potential.
- Native Potential ( E n a t i v e E_{native} E na t i v e ): -0.550 V
- Target Potential ( E t a r g e t E_{target} E t a r g e t ): -0.850 V
Voltage Shift ( Δ E \Delta E Δ E ): E t a r g e t − E n a t i v e = − 0.850 − ( − 0.550 ) = − 0.300 V E_{target} - E_{native} = -0.850 - (-0.550) = -0.300 V E t a r g e t − E na t i v e = − 0.850 − ( − 0.550 ) = − 0.300 V
This required shift of 300 mV must be achieved by applying sufficient CP current to overcome the specific polarization characteristics of the pipeline in its environment.
Practical Implications for CP Testers
For a CP1 tester, understanding these principles is not just academic. It explains why we take the measurements we do. When we measure an "on" potential, we are looking at the mixed potential of the polarized structure plus the IR drop in the soil. When we measure an "instant-off" potential, we are trying to determine the true polarized potential, free of IR drop, to see if we have successfully shifted the potential to E a E_a E a or beyond. The concepts of polarization and mixed-potential theory form the foundation for all CP criteria and troubleshooting techniques.