Study guide
3.2 Galvanic (Sacrificial Anode) CP Systems
AMPP CP1 Cathodic Protection Tester Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & CP Exam Overview
About the AMPP CP1 Tester Exam & Certification Path How to Study for CP1 & Navigate This Guide Corrosion Science & Industry Terminology Glossary Field Mathematics & Ohm's Law Fundamentals AMPP Ethics for the Corrosion Professional
2 Chapter 2: Fundamentals of Electrochemistry & Corrosion Cells
2.1 The Corrosion Cell: Anode, Cathode, Electrolyte & Metallic Path 2.2 Anodic & Cathodic Reactions on Carbon Steel 2.3 Galvanic Series & Electromotive Force (EMF) Series 2.4 Forms of Corrosion: Uniform, Galvanic, Pitting & Crevice 2.5 Factors Affecting Corrosion Rates: Oxygen, pH, Temperature & Flow
3 Chapter 3: Principles of Cathodic Protection
3.1 Cathodic Protection Theory & Mixed-Potential Diagrams 3.2 Galvanic (Sacrificial Anode) CP Systems 3.3 Impressed Current Cathodic Protection (ICCP) Systems 3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys 3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum
4 Chapter 4: Electrical Circuit Analysis for CP
4.1 Ohm's Law Applications in CP Circuits 4.2 Series & Parallel Resistance in CP Groundbeds & Piping 4.3 Kirchhoff's Voltage & Current Laws in Network Piping 4.4 Shunts: Types, Ratings & Current Calculations 4.5 Rectifier Operation & Transformer Tap Adjustments
5 Chapter 5: Reference Electrodes & Half-Cell Potentials
5.1 Copper/Copper Sulfate (CSE) Reference Electrode Construction & Maintenance 5.2 Silver/Silver Chloride (Ag/AgCl) & Zinc Reference Electrodes 5.3 Converting Potentials Between Reference Electrodes 5.4 Reference Electrode Care, Temperature Correction & Contamination Checks 5.5 High-Impedance Voltmeters & Contact Resistance Errors
6 Chapter 6: Field Measurement & Potential Criteria
6.1 Structure-to-Electrolyte Potential Measurement Procedures 6.2 The -850 mV CSE Polarized Criterion (NACE SP0169) 6.3 The 100 mV Polarization Decay Criterion 6.4 Understanding IR Drop & The Instant-Off Interruption Technique 6.5 Native, On, Polarized, & Off Potentials Comparison
7 Chapter 7: Advanced Field Survey Techniques
Soil Resistivity Testing: Wenner 4-Pin Method (ASTM G57) Soil Pin Spacing, Layering & Corrosivity Classification Close Interval Potential Surveys (CIPS) Direct Current Voltage Gradient (DCVG) Coating Fault Surveys Cathodic Protection Coupons for IR-Free Potential Measurements
8 Chapter 8: Test Stations, Isolation & Stray Current
8.1 Test Station Types, Lead Wires & Commissioning Inspection 8.2 Electrical Isolation Joints & Dielectric Flange Testing 8.3 Casing Isolation & Shorted Casing Testing 8.4 DC Stray Current Interference: Detection & Mitigation 8.5 AC Stray Current Interference & Induction Hazards (NACE SP0177)
9 Chapter 9: Industry Standards & Field Documentation
9.1 NACE SP0169: External Corrosion Control Overview 9.2 NACE TM0497: Measurement Techniques Standard 9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements 9.4 CP Data Collection, Logging & Quality Assurance 9.5 Rectifier Maintenance & Routine Inspection Logs 9.6 Anode Groundbed Testing & Resistance Measurements
10 Chapter 10: Electrical & Operational Safety for CP Personnel
10.1 Rectifier Electrical Safety, Lockout/Tagout (LOTO) & NFPA 70E 10.2 AC Induction Hazards Near High-Voltage Power Lines 10.3 Hazardous Atmospheres & Confined Space Safety at Test Vaults 10.4 Personal Protective Equipment (PPE) & Arc Flash Protection 10.5 Excavation, Trenching & Underground Utility Location (811) 10.6 Stop-Work Authority & Emergency Response Procedures
3.2 Galvanic (Sacrificial Anode) CP Systems
Key Takeaways Explain This Topic AI
Galvanic systems rely on the natural potential difference between dissimilar metals.
They do not require an external power source, making them ideal for remote locations.
The driving voltage is limited by the position of the metals in the galvanic series.
Common galvanic anode materials include magnesium, zinc, and aluminum alloys.
Galvanic systems are best suited for well-coated structures with low current requirements.
Last updated: July 2026
Galvanic (Sacrificial Anode) CP Systems
Galvanic cathodic protection, often referred to as sacrificial anode cathodic protection, is the simplest and most elegant application of CP principles. It leverages the natural electrochemical properties of metals to protect a structure without the need for an external power source. This section explores the mechanics, components, and appropriate applications of galvanic systems.
The Principle of Operation
The operation of a galvanic CP system is based directly on the Galvanic Series . When two dissimilar metals are electrically connected and immersed in a common electrolyte, a natural galvanic cell is formed. The metal that is more active (more electronegative or "less noble") in the galvanic series will become the anode and corrode, while the metal that is less active (more electropositive or "more noble") will become the cathode and be protected.
In a galvanic CP system, we deliberately connect a highly active metal (the sacrificial anode) to the structure we want to protect (the cathode, usually steel). Because the anode has a more negative open-circuit potential than the steel, electrons naturally flow from the anode, through the metallic connection, to the steel structure. This flow of electrons polarizes the steel in the cathodic direction, mitigating its corrosion. Meanwhile, the anode sacrifices itself, corroding away over time to protect the structure.
The Driving Voltage
The fundamental limitation of a galvanic system is its driving voltage . The driving voltage is simply the difference in potential between the open-circuit potential of the sacrificial anode and the polarized potential of the structure.
For example, if a magnesium anode has an open-circuit potential of -1.50 V (CSE) and the steel structure is polarized to -0.85 V (CSE), the driving voltage is:
Driving Voltage = 1.50 V - 0.85 V = 0.65 V
Because this driving voltage is inherently small (typically less than 1 volt), galvanic systems can only output a limited amount of current. According to Ohm's Law (I = V/R), if the driving voltage (V) is low, the resistance (R) of the circuit must also be low to produce a meaningful amount of current (I). Therefore, galvanic systems are typically ineffective in high-resistivity soils or on poorly coated structures that require massive amounts of current.
Components of a Galvanic System
A typical galvanic CP system installation is straightforward, consisting of a few key components:
The Sacrificial Anode: Cast from alloys of Magnesium, Zinc, or Aluminum. The choice depends on the environment (soil vs. seawater) and the required driving voltage.
The Backfill (for soil applications): Anodes buried in soil are usually packaged in a special chemical backfill, typically a mixture of gypsum, bentonite clay, and sodium sulfate. The backfill serves multiple crucial purposes:
It provides a uniform, low-resistivity environment immediately surrounding the anode, promoting uniform corrosion.
It prevents the anode from coming into direct contact with the soil, which could cause localized passivation (the formation of a resistive film on the anode surface).
It retains moisture, keeping the local resistivity low.
The Header Cable / Lead Wire: An insulated copper wire that electrically connects the anode to the structure.
The Test Station: A junction box where the anode lead wire and the structure lead wire meet. This allows the CP tester to easily measure the current output of the anode and to disconnect the anode for testing purposes.
The Structure Connection: The point where the cable is attached to the pipeline, typically via an exothermic weld (e.g., Cadweld) to ensure a low-resistance, durable connection.
Advantages of Galvanic Systems
Galvanic systems offer several distinct advantages, making them the preferred choice in many scenarios:
No External Power Required: This is the most significant advantage. They can be installed in remote areas where commercial power is unavailable or prohibitively expensive to route.
Low Maintenance: Once installed, galvanic systems require very little maintenance other than periodic testing. There are no moving parts or electronic components to fail.
No Stray Current Interference: Because the current output is low and the anodes are typically placed close to the structure, galvanic systems almost never cause stray current interference problems on neighboring foreign structures.
Self-Regulating: As the structure polarizes, the potential difference between the anode and the structure decreases, which naturally reduces the current output, preventing over-protection.
Simple Installation: The installation process is generally straightforward and less costly than installing an ICCP system.
Limitations of Galvanic Systems
Despite their benefits, galvanic systems have critical limitations that must be considered:
Low Current Output: As discussed, the low driving voltage limits the current output. They cannot protect massive, poorly coated structures (like bare pipelines).
Ineffective in High Resistivity Environments: In soils with high electrical resistivity, the low driving voltage cannot overcome the high circuit resistance, resulting in insufficient protective current.
Limited Lifespan: The anodes are consumed. While designed to last many years (often 10-20 years), they will eventually deplete and require complete replacement.
Inefficient for Large Structures: To protect a large structure with galvanic anodes, an impractical number of anodes might be required, making ICCP a more economical choice.
Applications
Galvanic systems are typically deployed in specific situations:
Protecting well-coated pipelines with low current requirements.
Providing "hot spot" protection on specific sections of a pipeline known to be corrosive.
Protecting underground storage tanks (USTs).
Protecting internal surfaces of water tanks.
Protecting offshore structures where the low resistivity of seawater compensates for the low driving voltage.
Worked Example: Calculating Anode Life
The theoretical life of a galvanic anode can be estimated using Faraday's Law, combined with the specific capacity and efficiency of the anode material. The basic formula is:
Life (years) = (Weight (lbs) * Capacity (amp-hours/lb) * Efficiency) / (Current Output (amps) * 8760 hours/year)
Assume we have a 17 lb High-Potential Magnesium anode. Its theoretical capacity is roughly 1000 amp-hours/lb, and its typical efficiency in soil is about 50%. If the anode is outputting a constant 0.050 Amps (50 mA):
Life = (17 lbs * 1000 Ah/lb * 0.50) / (0.050 A * 8760) Life = 8500 / 438 Life ≈ 19.4 years
This calculation is essential for designing systems that will meet the required design life of the asset.