Study guide

3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum

AMPP CP1 Cathodic Protection Tester Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & CP Exam Overview

About the AMPP CP1 Tester Exam & Certification Path How to Study for CP1 & Navigate This Guide Corrosion Science & Industry Terminology Glossary Field Mathematics & Ohm's Law Fundamentals AMPP Ethics for the Corrosion Professional

2 Chapter 2: Fundamentals of Electrochemistry & Corrosion Cells

2.1 The Corrosion Cell: Anode, Cathode, Electrolyte & Metallic Path 2.2 Anodic & Cathodic Reactions on Carbon Steel 2.3 Galvanic Series & Electromotive Force (EMF) Series 2.4 Forms of Corrosion: Uniform, Galvanic, Pitting & Crevice 2.5 Factors Affecting Corrosion Rates: Oxygen, pH, Temperature & Flow

3 Chapter 3: Principles of Cathodic Protection

3.1 Cathodic Protection Theory & Mixed-Potential Diagrams 3.2 Galvanic (Sacrificial Anode) CP Systems 3.3 Impressed Current Cathodic Protection (ICCP) Systems 3.4 Sacrificial Anode Materials: Mg, Zn, & Al Alloys 3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum

4 Chapter 4: Electrical Circuit Analysis for CP

4.1 Ohm's Law Applications in CP Circuits 4.2 Series & Parallel Resistance in CP Groundbeds & Piping 4.3 Kirchhoff's Voltage & Current Laws in Network Piping 4.4 Shunts: Types, Ratings & Current Calculations 4.5 Rectifier Operation & Transformer Tap Adjustments

5 Chapter 5: Reference Electrodes & Half-Cell Potentials

5.1 Copper/Copper Sulfate (CSE) Reference Electrode Construction & Maintenance 5.2 Silver/Silver Chloride (Ag/AgCl) & Zinc Reference Electrodes 5.3 Converting Potentials Between Reference Electrodes 5.4 Reference Electrode Care, Temperature Correction & Contamination Checks 5.5 High-Impedance Voltmeters & Contact Resistance Errors

6 Chapter 6: Field Measurement & Potential Criteria

6.1 Structure-to-Electrolyte Potential Measurement Procedures 6.2 The -850 mV CSE Polarized Criterion (NACE SP0169) 6.3 The 100 mV Polarization Decay Criterion 6.4 Understanding IR Drop & The Instant-Off Interruption Technique 6.5 Native, On, Polarized, & Off Potentials Comparison

7 Chapter 7: Advanced Field Survey Techniques

Soil Resistivity Testing: Wenner 4-Pin Method (ASTM G57) Soil Pin Spacing, Layering & Corrosivity Classification Close Interval Potential Surveys (CIPS) Direct Current Voltage Gradient (DCVG) Coating Fault Surveys Cathodic Protection Coupons for IR-Free Potential Measurements

8 Chapter 8: Test Stations, Isolation & Stray Current

8.1 Test Station Types, Lead Wires & Commissioning Inspection 8.2 Electrical Isolation Joints & Dielectric Flange Testing 8.3 Casing Isolation & Shorted Casing Testing 8.4 DC Stray Current Interference: Detection & Mitigation 8.5 AC Stray Current Interference & Induction Hazards (NACE SP0177)

9 Chapter 9: Industry Standards & Field Documentation

9.1 NACE SP0169: External Corrosion Control Overview 9.2 NACE TM0497: Measurement Techniques Standard 9.3 Regulatory Compliance: PHMSA, DOT, & EPA Requirements 9.4 CP Data Collection, Logging & Quality Assurance 9.5 Rectifier Maintenance & Routine Inspection Logs 9.6 Anode Groundbed Testing & Resistance Measurements

10 Chapter 10: Electrical & Operational Safety for CP Personnel

10.1 Rectifier Electrical Safety, Lockout/Tagout (LOTO) & NFPA 70E 10.2 AC Induction Hazards Near High-Voltage Power Lines 10.3 Hazardous Atmospheres & Confined Space Safety at Test Vaults 10.4 Personal Protective Equipment (PPE) & Arc Flash Protection 10.5 Excavation, Trenching & Underground Utility Location (811) 10.6 Stop-Work Authority & Emergency Response Procedures

3.5 ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum

Key Takeaways Explain This Topic AI

ICCP anodes are designed to discharge large amounts of current while consuming very slowly.

Mixed Metal Oxide (MMO) anodes are the modern industry standard due to ultra-low consumption, light weight, and high current density.

High Silicon Cast Iron (HSCI) is a traditional, durable, but heavy anode material still used in specific groundbed designs.

Graphite anodes are economical but brittle and must be installed carefully with carbon backfill to prevent rapid consumption.

Platinum is used as a thin coating on titanium or niobium substrates, offering very high current densities for specialized applications.

Last updated: July 2026

ICCP Anode Materials: MMO, Graphite, HSCI, & Platinum

Unlike galvanic anodes, which are designed to sacrifice themselves rapidly, the anodes used in Impressed Current Cathodic Protection (ICCP) systems must survive for decades while discharging massive amounts of current driven by a rectifier. Therefore, ICCP anode materials are selected for their relative inertness—they possess extremely low consumption rates.

The evolution of ICCP anode materials has moved from heavy, bulky materials to lightweight, highly advanced catalytic coatings. This section details the four most prominent ICCP anode materials encountered by CP testers.

1. Mixed Metal Oxide (MMO)

Mixed Metal Oxide (MMO) anodes represent the current state-of-the-art and are by far the most common ICCP anode installed today.

Composition and Structure

An MMO anode is not a solid block of metal. It consists of a highly stable, commercially pure titanium substrate (which can be a wire, a rod, a tube, an expanded mesh, or a ribbon). This titanium base is coated with a microscopic layer of mixed metal oxides—typically oxides of rare earth metals like iridium, ruthenium, and tantalum.

The Titanium Substrate: Titanium is unique because, under anodic conditions, it immediately forms a highly resistive oxide film that prevents it from discharging current or corroding. It acts solely as a conductive pathway to deliver electrons to the coating.

The MMO Coating: The metal oxide coating is the active part of the anode. It acts as an electrocatalyst, allowing the anodic reaction (typically the generation of oxygen or chlorine gas) to occur on its surface with virtually no consumption of the coating itself.

Properties and Advantages

Ultra-Low Consumption Rate: MMO anodes have a consumption rate measured in milligrams per amp-year (mg/A-yr). They essentially do not wear away during their design life.

High Current Density: They can discharge significant current from a very small surface area.

Lightweight and Flexible: Because the titanium substrate can be fashioned into thin wires or flexible mesh ribbons, MMO anodes are incredibly easy to handle, transport, and install compared to heavy traditional anodes.

Versatility: By tweaking the specific mix of oxides (e.g., Iridium/Tantalum for soil/freshwater, Ruthenium/Iridium for seawater), MMO anodes can be optimized for almost any environment.

2. High Silicon Cast Iron (HSCI)

Before the widespread adoption of MMO, High Silicon Cast Iron was the premier ICCP anode material. It is still used today, particularly in deep well groundbeds where its weight can aid in installation.

Composition and Structure

HSCI anodes are solid, heavy, cast alloy bars (typically tubular or solid cylinders). The critical element is silicon (usually around 14.5%), often alloyed with chromium (around 4.5%) to improve performance in chloride-rich environments.

When current is discharged from an HSCI anode, the iron on the surface oxidizes, but the silicon forms a highly conductive, protective silicon dioxide ( S i O 2 SiO_2 S i O 2 ​ ) film on the anode surface. This film significantly slows further consumption of the base metal.

Properties and Considerations

Low Consumption Rate: Generally around 0.25 to 1.0 pounds per amp-year (lb/A-yr). While much higher than MMO, it is still very low compared to galvanic materials.

Durable: HSCI anodes are physically robust and can withstand rough handling better than graphite.

Heavy: A typical HSCI anode can weigh 50 to 100 pounds, making shipping and installation physically demanding.

Gas Venting: Like all ICCP anodes in soil, they generate gases (oxygen and chlorine). In deep wells, proper venting is required to prevent "gas blocking," which increases circuit resistance.

3. Graphite

Graphite is one of the oldest ICCP anode materials. It is a non-metal (a crystalline form of carbon) that conducts electricity.

Composition and Structure

Graphite anodes are manufactured by baking carbon at extremely high temperatures. The resulting material is porous. Because moisture penetrating these pores can cause the anode to break apart from the inside when current is discharged, graphite anodes used in CP are heavily impregnated with linseed oil, microcrystalline wax, or special resins to seal the pores.

Properties and Considerations

Economical: Graphite is relatively inexpensive to manufacture.

Consumption Rate: Approximately 0.5 to 2.0 lb/A-yr. They are highly dependent on the carbonaceous backfill (coke breeze). The backfill must carry the bulk of the current discharge to protect the graphite.

Brittle: This is their biggest drawback. Graphite anodes are fragile and easily broken during transport, installation, or if the soil shifts significantly after burial.

Current Density Limit: They cannot be driven as hard as MMO or HSCI anodes. Exceeding their recommended current density will cause rapid failure.

4. Platinized Anodes

Platinum is a noble metal that acts as an excellent catalyst for anodic reactions and has a near-zero consumption rate. However, solid platinum is prohibitively expensive. Therefore, platinized anodes use a thin layer of platinum clad or electroplated over a substrate.

Composition and Structure

Similar to MMO anodes, the substrate is typically a valve metal that passivates under anodic conditions, usually Titanium or Niobium. Niobium is often preferred because its breakdown voltage (the voltage at which the protective oxide film fails) is much higher than titanium, allowing the system to operate at higher voltages if necessary.

Properties and Applications

Extremely High Current Density: Platinized anodes can push massive amounts of current from a very small surface area.

Cost: Even with a thin coating, they are very expensive.

Applications: Because of the cost and the advent of cheaper MMO alternatives, platinized anodes are mostly reserved for specialized, high-stress environments. They are frequently used in internal protection of water tanks, heater treaters, and in some offshore applications where extremely high current outputs are required from small fixtures.

Summary of ICCP Materials

Material Typical Consumption Rate Physical Characteristics Primary Use Case

MMO < 1 milligram / A-yr Very light, flexible forms (wire, ribbon, tube) Industry standard for most new soil, water, and concrete applications.

HSCI 0.25 - 1.0 lb / A-yr Heavy, solid cast cylinders Traditional deep well groundbeds, environments where weight aids installation.

Graphite 0.5 - 2.0 lb / A-yr Solid cylinders, brittle, porous (needs impregnation) Economical option for conventional shallow groundbeds in soil.

Platinum < 0.01 milligram / A-yr Thin coating on Ti or Niobium substrate Specialized high-current density applications (internal tanks, offshore).

For a CP1 tester, recognizing the type of anode installed (often found in the system's historical records) is vital. Knowing that an MMO groundbed shouldn't lose mass, while a graphite groundbed might fail prematurely if the coke breeze is compromised, informs troubleshooting strategies when groundbed resistance begins to rise.